User's Manual
Table Of Contents
- ROAMEO Family Wireless Intercom System
- •TR-1800 •AP-1800
- CHAPTER 1 Certification Information
- CHAPTER 2 Introduction
- CHAPTER 3 System Overview
- CHAPTER 4 Site Survey
- CHAPTER 5 Installation
- CHAPTER 6 Basic Operation
- CHAPTER 7 Beltpack Overview
- System Quick Start
- Button Operation – Common
- Menu Structure – Main Menu Access
- Aux Input Menu
- AUX DIM Menu
- Volume Limit Menu
- Headset Select Menu
- Mic Gain
- Sidetone
- Mic Noise Gate
- Hot Mic
- Talk/Listen LED Buttons
- Front Display Brightness
- Top Display Brightness
- LCD Timeout
- Call Tally Talk
- Screen Flip
- Master Talk Switch
- Low Battery Alert
- Call Waiting Alert
- DECT Connection Alert
- Matrix Connection Alert
- Dark Mode Boot Alert
- Key Clicks Alert
- Alerts Levels
- Key Assignments
- Icon Help
- Scroll List
- CHAPTER 8 Access Point Overview
- AP-1800 Front Panel Description
- IPedit Requirements
- IPedit Main Window
- Configuration
- Device Name Field
- Description Field
- Version Field
- IP Address Field
- Netmask Field
- Gateway Address Field
- DNS Server Field
- Domain Name Field
- MAC Address Field
- Use Static IP Settings Check Box
- Disable RSTP Check Box
- Type Field
- Status Field
- Sessions Field
- AP Channels Field
- BP Channels Field
- Sync Display Box
- System ID Field
- PIN Field
- Zone Drop Down Menu
- CODEC Drop Down Menu
- AP ID Number Field
- Sync Master Check Box
- Intercom Alpha Field
- Channel Description Field
- Destination Type Drop Down Menu
- Destination Device Name Field (OMNEO devices and AP-1800 ROAMEO Access Point Only)
- Destination IP Address Field
- Destination Description Field
- Destination Channel Drop Down Menu
- Destination Channel Description Field
- Receiver Latency Field
- DECT BPID
- DECT Zone Selection Field
- Configuration
- CHAPTER 9 Maintenance
- CHAPTER 10 Troubleshooting, Accessories and Replacements
110 Beltpack Overview ROAMEO System
Bosch Security Systems, Inc.
Technical Manual
F.01U.306.750
Rev. 01
1. Using the UP and DOWN arrow buttons, select the Alerts icon.
2. Press the SELECT button.
The alerts menu options appear in the beltpack display screen.
3. Using the UP and DOWN arrow buttons, select the DECT connection icon.
4. Press the SELECT button.
The DECT connection enable/disable 2-position indicator becomes active.
5. Using the UP and DOWN arrow buttons, enable the DECT connection alert.
The 2-position indicator turns green.
OR
Using the UP and DOWN arrow buttons, disable the DECT connection alert.
The 2-position indicator returns to the original disabled blue.
6. Once finished, press the SELECT button to save the modification.
7. Press and hold the MENU button to exit the menu.
Matrix Connection Alert
The Matrix Connection alert is used to enable or disable an audio alert when the TR-1800 ROAMEO beltpack has lost its
connection to the Matrix or on power up when the AP has not yet connected to the Matrix.
The alert heard is a short, high-frequency tone followed immediately by a lower frequency tone, repeating every three seconds
until the beltpack connection is restored with the matrix.
The default setting for the matrix connection alert is enabled.
To enable/disable the matrix connection alert, do the following:
1. Using the UP and DOWN arrow buttons, select the Alerts icon.
2. Press the SELECT button.
The alerts menu options appear in the beltpack display screen.
3. Using the UP and DOWN arrow buttons, select the matrix connection icon.
4. Press the SELECT button.
The matrix connection enable/disable 2-position indicator becomes active.
5. Using the UP and DOWN arrow buttons, enable the matrix connection alert.
The 2-position indicator turns green.
OR
Using the UP and DOWN arrow buttons, disable the matrix connection alert.
The 2-position indicator returns to the original disabled blue.
6. Once finished, press the SELECT button to save the modification.
7. Press and hold the MENU button to exit the menu.
Enabled
Disabled