DICENTIS Wireless Conference System en Installation Manual
DICENTIS Table of Contents | en 3 Table of contents 1 Safety 4 1.1 Battery Pack 4 1.2 Statements for FCC & Industry Canada 4 2 About this manual 6 2.1 Intended audience 6 2.2 Alerts and notice signs 6 2.3 Copyright and disclaimer 6 2.4 Document history 7 3 System overview 3.1 Extended system requirements 10 4 Installation planning 11 4.1 Unpacking 12 4.
en | Safety 1 DICENTIS Safety Prior to installing or operating products, always read the Important Safety Instructions which are available as a separate multilingual document: Important Safety Instructions (Safety_ML). These instructions are supplied together with all equipment that can be connected to the mains supply.
DICENTIS Safety | en 5 Notice! The Wireless Discussion Devices and the Wireless Access Point comply with FCC radiation exposure limits set forth for an uncontrolled environment. The Wireless Discussion Devices and the Wireless Access Point should be installed and operated with minimum distance of 20 cm to your body. Bosch Security Systems B.V. Installation Manual 2015.02 | V1.
en | About this manual 2 DICENTIS About this manual The purpose of this manual is to provide information required for installing the DICENTIS Wireless Conference System. – Please read this manual carefully before installing any of the products of the DICENTIS Wireless Conference System. – – Retain all documentation supplied with the products for future reference. This installation manual is available as a digital document in the Adobe Portable Document Format (PDF).
DICENTIS 2.4 About this manual | en 7 Document history Release date Documentation version Reason 2015.02 V1.0 1st edition. Bosch Security Systems B.V. Installation Manual 2015.02 | V1.
en | System overview 3 DICENTIS System overview The DICENTIS Wireless Conference System is a “standalone” IP based system. It uses WiFi IEEE 802.11n for wireless distribution and processing of audio and data signals.
DICENTIS System overview | en 1. 9 The Wireless Access Point (DCNM-WAP) is the central device of the DICENTIS Wireless Conference System. The Wireless Access Point is used to: – Host a web interface for licensing, configuring and controlling the system. – Control the system audio and routing of the audio from and to the Wireless Devices. – Environment wireless channel scanning. The best available wireless channel will be chosen for the system. – Camera control.
en | System overview 3.1 DICENTIS Extended system requirements The following requirements are valid if you want to extend your system with a network switch or cameras: – Network switch and camera installation instructions are not part of this installation manual; please consult the product related documentation of the supplier. – Notice that a DHCP server is needed for both the Wireless Access Point and the cameras. Cameras Typical, the Bosch HD Conference Dome is used.
DICENTIS 4 Installation planning | en 11 Installation planning Make sure you have all components for installing and connecting the DICENTIS Wireless Conference System (see System overview, page 8). – Familiarize yourself with the products capabilities of the DICENTIS Wireless Conference System (see System overview, page 8 and the paragraphs Control capacity and Coverage area in this section. – Use only Bosch specified installation materials and tools (see Additional components, page 12). 1.
en | Installation planning 4.1 DICENTIS Unpacking This equipment should be unpacked and handled with care. If an item appears to be damaged, notify the shipper immediately. If any items are missing, notify your Bosch representative. The original packaging is the safest container in which to transport products and can be used to return products for service if necessary. 4.
DICENTIS 5 Installation Wireless Access Point | en 13 Installation Wireless Access Point Use the following steps to install the Wireless Access Point (DCNM-WAP). 1. Make sure all equipment is available as described in 1) Scope of delivery. 2. Optional set the “Brand logo” in the correct orientation. 3. Connect the cabling and install the Wireless Access Point to the wall/ceiling or tripod floor stand. 4. Power on the Wireless Access Point.
en | Installation Wireless Access Point DICENTIS 3) Cabling and wall/ceiling/tripod floor stand installation The Wireless Access Point is provided to be installed to a wall, a ceiling or on a tripod floor stand. Take care of the installation location regarding the wireless signal coverage area between the Wireless Access Point and the Wireless Devices. See Installation planning, page 11. Caution! ! Do not open the Wireless Access Point. Any hardware change makes the product certificates invalid.
DICENTIS Installation Wireless Access Point | en 15 Wall or ceiling installation Use the mounting bracket to attach the Wireless Access Point to a wall or ceiling. TORX 10 01 02 Figure 5.3: Mounting to a wall or ceiling Bosch Security Systems B.V. Installation Manual 2015.02 | V1.
en | Installation Wireless Access Point DICENTIS Tripod floor stand installation Use the mounting bracket to install the Wireless Access Point on a Bosch LBC1259/01 universal tripod floor stand. 01 02 Figure 5.4: Mounting on a tripod floor stand 2015.02 | V1.0 | Installation Manual Bosch Security Systems B.V.
DICENTIS Installation Wireless Access Point | en 17 4) Power on / connections and indicators The DCNM-WAP is powered via one of the three power supply sources marked with an * in the table below. As soon the power supply is provided, the Wireless Access Point is powered on, and the six LEDs (1) on the front side are all on. – To configure the DCNM-WAP, refer to the software configuration manual of the DICENTIS Wireless Conference System. 1 2 3 45 6 Figure 5.
en | Installation Wireless Access Point Item 4 DICENTIS Description Balanced audio line output socket: Connection to a public address system, audio mixers or to a voice logging system for audio registration of all spoken conference proceedings. Use standard line output cabling. 6.3mm (1/4") jacks with the following pinning: Tip: Live (+) Ring: Return (-) Sleeve: Shield 6 Balanced audio line input socket: Connection from audio source. Use standard line output cabling. 6.
DICENTIS Installation Wireless Devices and Accessories | en 19 Installation Wireless Devices and Accessories 6 The Wireless Devices are used to add participants to a discussion. See System overview, page 8, if required. Scope of delivery – The DCNM-WD and DCNM-WDE are shipped without (accessory) parts. Installation The Wireless Devices are free‑standing (table-top use). No mechanical installation, other than the accessories as described below, is required.
en | Installation Wireless Devices and Accessories 3. DICENTIS Install the Battery Pack (15) in each Wireless Device to be used. Refer to Battery Pack , page 24. 4. Attach the microphones to the Wireless Devices (11). Refer to Microphones, page 22. 5. Place the Wireless Devices in the coverage area of the Wireless Access Point (DCNMWAP). See Installation planning, page 11, if required.
DICENTIS Installation Wireless Devices and Accessories | en Item Description 17 (DCNM-WLIION) Battery Pack capacity test button. See Battery Pack , page 24. 18 21 (DCNM-WLIION) Battery Pack capacity LED (5x) indicators. See Battery Pack , page 24. Bosch Security Systems B.V. Installation Manual 2015.02 | V1.
en | Installation Wireless Devices and Accessories 6.1 DICENTIS Microphones 9 Figure 6.1: DCNM‑HDMIC or DCNM‑MICx to Wireless Device connection Both the DCNM‑HDMIC High Directive Microphone and DCNM-MICL/S Stem Microphone are typically used with the DCN multimedia device and DICENTIS wireless devices. 2 1 1 2 3 3 7 4 6 8 7 6 4 8 5 5 Figure 6.2: DCNM‑HDMIC and DCNM‑MICx front and bottom view 2015.02 | V1.0 | Number Description 1 LED indicator.
DICENTIS Installation Wireless Devices and Accessories | en Number Description 4 Connection guidance. 5 Slider guidance. 6 Connector plug. 7 Lockslider for lock release (Press and shift to release). 8 Lock. 9 Device female connector. 23 How to connect or remove the microphone The microphone can be easily connected to the device: 9 6 4 75 8 Figure 6.3: DCNM‑HDMIC or DCNM‑MICx to DCNM‑MMD connection To do so: 1.
en | Installation Wireless Devices and Accessories DICENTIS Battery Pack 6.2 The Battery Pack (DCNM-WLIION) is used to: – Provide the power supply of the Wireless Devices (DCNM-WD and DCNM-WDE). – Refer to Installation Wireless Devices and Accessories, page 19, if required. Caution! It is advised to charge the Battery Pack immediately after receipt. Use only the DCNM-WCH05 ! to charge the Battery Pack. Empty Battery Packs should be charged within 30 days.
DICENTIS Installation Wireless Devices and Accessories | en 2. 25 Turn the Battery Pack to top view (1) and hook the securing nocks (6) in the Wireless Device battery compartment. 3. Gently push down the Battery Pack until it locks (2) into the Wireless Device Battery Pack compartment. How to remove the Battery Pack 1. Turn the Wireless Device up‑side‑down. 2. Remove the Battery Pack in reverse order by push‑and‑hold the locking clip (2) and gently pushing up the Battery Pack. 3.
en | Installation Wireless Devices and Accessories 6.3 DICENTIS Charger The Charger (DCNM-WCH05) is used for (and can be used for connection to IT power distribution systems): – Charging the Battery Pack (DCNM-WLIION). – One Charger can charge a maximum of 5 Battery Packs at the same time. Scope of delivery – The DCNM-WCH05 is shipped with the following parts: – 1x Mains power cable. – 1x Loop‑through mains power cable. – 1x Mounting bracket. – 1x Safety instructions.
DICENTIS Installation Wireless Devices and Accessories | en 27 Item Description 4 Power on/off LED: Is on when the power cable is connected to Charger and the other end is connected to the mains power supply. 5 Mains power supply socket/inlet. The maximum current handling of the inlet is 10A. Therefore there is a limitation of the number of loop‑through Chargers. For details, see the Mains power connection / loop‑through paragraph in this section.
en | Installation Wireless Devices and Accessories DICENTIS The Charger can be free‑standing or fixed installed in more permanent installations (i.e. to a wall), using the mounting bracket. TORX 10 01 02 TORX 10 03 Figure 6.7: Installation to a wall 2015.02 | V1.0 | Installation Manual Bosch Security Systems B.V.
DICENTIS Installation Wireless Devices and Accessories | en 29 When installing more than one Charger next to each other, be sure that: – The vertical distance between two brackets is at least 340 mm (refer to d1 in the next figure). – The horizontal distance between two brackets is at least 195 mm (refer to d2 in the next figure). d1 d2 Mains power supply connection / loop‑through 1. Connect a locally approved mains power cord to the Charger mains power supply socket/ inlet (5). 2.
en | Installation Wireless Devices and Accessories DICENTIS Install/remove the Battery Pack 1. Install the Battery Pack until it locks in the Charger, as illustrated in the next figure. – 2. Remove the Battery Pack in the reversed order by gently take‑out the Battery Pack. Connect the mains power supply to the Charger to power on the Charger and to start the charging process. – Power LED (4) is on when receiving mains power supply.
DICENTIS 7 System power on and configuration | en 31 System power on and configuration Consult the software configuration manual of the DICENTIS Wireless Conference System for power on and configuration details of the Wireless Access Point and Wireless Devices. – For documentation, refer to the DICENTIS Wireless Conference System product related information on: www.boschsecurity.com > Country of your choice > Conference Systems > DICENTIS Wireless Conference System Bosch Security Systems B.V.
en | Maintenance DICENTIS Maintenance 8 The DICENTIS Wireless Conference System requires minimum maintenance. To ensure for trouble‑free operation, clean and inspect the system components on a regular basis: 8.1 Cleaning Caution! ! Do not use alcohol, ammonia, petroleum solvents or abrasive cleaners to clean the system components. 1. Clean the Wireless Devices with a soft cloth moistened very slightly with a weak soap and water solution. 2.
DICENTIS Technical data | en 9 Technical data 9.1 Wireless Access Point (DCNM-WAP) 33 Technical specifications Radio WIFI standard IEEE 802.11n Frequency Range 2.4 GHz and 5 GHz (ISM license free) Electrical Supply voltage (PSU) 100‑240 Vac 50‑60 Hz in 48 Vdc out PoE 802.3af, 802.3at - type 1 mode A (endspan), mode B (midspan) DCNM system supply 48 Vdc Power consumption 10 W Frequency response 80 Hz - 20 kHz THD at nominal level <0.
en | Technical data DICENTIS Environmental Operating temperature 5 ºC to +45 ºC (41 ºF to +113 ºF) Storage temperature -20 ºC to +70 ºC (-4 ºF to +158 ºF) Relative humidity < 95 %, > 5 % Approvals and certifications EU CE, WEEE US UL, FCC CA CSA, ICES‑003, EPS KR KC AU/NZ RCM, MEPS RU/KZ/BY EAC JP PSE, MIC CN China RoHS, CCC, CMIIT SA SASO BR ANATEL The system is WiFi Certified by the WiFi Alliance. 2015.02 | V1.0 | Installation Manual Bosch Security Systems B.V.
DICENTIS 9.2 Technical data | en 35 Wireless Devices (DCNM-WD and DCNM-WDE) Technical specifications General 4.3 inch Screen size (DCNM-WDE only) Screen type Capacitive multi-touch (DCNM-WDE only) Supported contactless NFC tag According to: ISO/IEC14443 Type A (from 106 kbps (DCNM-WDE only) to 848 kbps. MIFARE 106kbps). Radio WIFI standard IEEE 802.11n Frequency Range 2.4 GHz and 5 GHz (ISM license free) Electrical Supply voltage (battery pack) 7.
en | Technical data DICENTIS Mechanical Mounting Tabletop Dimensions (H x W x D) without 259 x 139 x 72 mm microphone (10.2 X 5.5 x 2.8 in) Weight: DCNM-WD 590 g (1.30 Lb) DCNM-WD + Battery Pack 1051 g (2.32 lb) DCNM-WDE 670 g (1.47 lb) DCNM-WDE + Battery Pack 1131 g (2.
DICENTIS 9.3 Technical data | en 37 Battery Pack (DCNM-WLIION) Technical specifications Electrical Nominal output Voltage 7.5 VDC Capacity 12800 mAh Mechanical Dimensions (H x W x D) 99.9 x 136.5 x 22 mm (3.93 x 5.37 x 0.87 in) Weight 1774 g (3.
en | Technical data 9.4 DICENTIS Charger (DCNM-WCH05) Technical specifications Electrical Supply Voltage 100-240 Vac +/- 10 % 50/60 Hz Maximum power consumption 300 W Mechanical Dimensions (H x W x D) 340 x 195 x 82 mm (13.4 x 7.6 x 3.2 in) Weight (without batteries) 1.8 kg (3.
DICENTIS 9.5 Technical data | en 39 High Directive Microphone (DCNM-HDMIC) Technical specification Electrical Bandwith 100 Hz – 15 kHz according IEC 60914 Dynamic range > 96 dB Nominal input 80 dB SPL Maximum input 110 dB SPL Equivalent noise 12 dB SPL Mechanical Mounting Plug and fasten into DCN multimedia devices and DICENTIS wireless devices. Dimensions (H x W x D) 108 x 21.5 x 60 mm (4.25 X 0.85 x 2.36 in) Weight 0.035 kg (0.
en | Technical data 9.6 DICENTIS Stem Microphones (DCNM-MICx) Technical specifications Electrical Bandwidth 125 Hz – 15 kHz according IEC 60914 Dynamic range >100 dB Nominal input 85 dB SPL Maximum input 115 dB SPL Equivalent noise 15 dB SPL Mechanical Mounting Plug and fasten into DICENTIS wireless devices. Length: DCNM‑MICS (without connector) 310 mm (12.21 in) DCNM‑MICL(without connector) 480 mm (19.90 in) Connector 77.15 x 60.47 mm (3.40 x 2.38 in) Weight: DCNM‑MICS 91 g (0.
Bosch Security Systems B.V. Torenallee 49 5617 BA Eindhoven The Netherlands www.boschsecurity.com © Bosch Security Systems B.V.
