ALLPLEX track Personnel Transmitter ATX-TRM-304T01 | ATX-TRM-433T01 en Installation Manual
ALLPLEX track Personnel Transmitter Table of Contents | en 3 Table of contents 1 Copyright, Safety and Warranty 4 1.1 Copyright information 4 1.2 Important safety notes 5 1.3 Safety precautions 6 1.4 FCC information 6 2 Introduction 7 3 System Overview 8 4 Installation and Setup 9 4.1 Removing the Cover 9 4.2 Battery 5 Enabling and Disabling Features 10 5.1 Selecting Transmitter Radio Frequency 10 5.2 Factory Reset 11 5.3 Activating Configuration Mode 12 5.
en | Copyright, Safety and Warranty ALLPLEX track Personnel Transmitter 1 Copyright, Safety and Warranty 1.1 Copyright information All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of BOSCH SECURITY SYSTEMS. This manual is provided pursuant to a license agreement containing restrictions on their use.
ALLPLEX track Personnel Transmitter 1.2 Copyright, Safety and Warranty | en 5 Important safety notes 1. Read, Follow, and Retain Instructions – All safety and operating instructions must be read and followed properly before putting the unit into operation. Retain instructions for future reference. 2. Consider all Warnings – Adhere to all warnings on the unit and in the operating instructions. 3. Accessories – Use only accessories recommended by the manufacturer or those sold with the product.
en | Copyright, Safety and Warranty 1.3 ALLPLEX track Personnel Transmitter Safety precautions Disposal Your Bosch product has been developed and manufactured using highquality materials and components that can be reused. This symbol means that electronic and electrical devices that have reached the end of their working life must be disposed of separately from household waste. In the EU, separate collecting systems are already in place for used electrical and electronic products.
ALLPLEX track Personnel Transmitter 2 Introduction | en 7 Introduction The ALLPLEX track Personnel Transmitters are security transmitters designed to work with the Security Escort system. When an alarm is initiated, a signal identifying you and your location is sent to the Security Escort Central Console. The Central Console displays your location on a map along with related information. Robert Bosch (SEA) Pte Ltd Installation Manual 2014.03 | V1.0.
en | System Overview 3 ALLPLEX track Personnel Transmitter System Overview During an emergency, a person presses and holds the alarm button to produce an alarm. Generally the system sounders, strobes, or sirens activate within two seconds. The alarm signal transmits to the receivers which relay the alarm signal to the transponder or AT coordinator, and to the central console.
ALLPLEX track Personnel Transmitter 4 Installation and Setup | en 9 Installation and Setup This section provides information for system planners and configurators. 4.1 Removing the Cover Figure 4.1: Back of Transmitter 1 Retaining Screw 2 Lower Part Instructions 1. Remove the belt clip, if used. 2. Remove the retaining screw on the back of the enclosure. 3. Use a flat-head screwdriver to pry the lower part of the front cover away from the enclosure. 4.
en | Enabling and Disabling Features 5 ALLPLEX track Personnel Transmitter Enabling and Disabling Features Figure 5.1: Components of the transmitter 1 Dip Switch for Radio Frequency 4 Test Button 2 Battery Compartment (3V) 5 Lanyard 3 Alarm Button 5.1 Selecting Transmitter Radio Frequency The radio frequency (RF) is set as 304 MHz by default. To change the RF to 303.825 MHz, set dip switch 1 to the OFF position and dip switch 2 to the ON position. To change the RF to 433.
ALLPLEX track Personnel Transmitter Enabling and Disabling Features | en 11 Figure 5.2: Selecting Transmitter Radio Frequency Diagram Radio Frequency Switch Number 1 Switch Number 2 1 304 MHz (default) OFF OFF 2 303.825 MHz OFF ON 3 433.42 MHz ON OFF ON ON Used for Factory Reset Notice! Remove the battery before setting the dip switches. Use a white marker to indicate the configured RF on the back of the transmitter after setting the dip switches.
en | Enabling and Disabling Features ALLPLEX track Personnel Transmitter Feature Value Supervision Tracking Disabled Lanyard Disabled Autotracking Interval 7 secs Supervision Tracking Interval 90 secs Table 5.2: Factory Reset Features 5.3 Activating Configuration Mode Configuration mode on the transmitter is activated by going into the test mode. Note that this mode is not available if the Man-Down or Lanyard snatch alarms are triggered and active.
ALLPLEX track Personnel Transmitter 6 Basic Transmitter Features | en 13 Basic Transmitter Features This section provides information of the various features of the transmitter. 6.1 Transmitting a Manual Alarm Initiate an alarm by pressing and holding the Alarm button for 1 second. This emits a series of mixed tones for 2 seconds and sends an alarm signal to the Central Console. If alarm is activated within sight of a receiver, the red LED on the receiver lights up.
en | Wearing the Transmitter 7 ALLPLEX track Personnel Transmitter Wearing the Transmitter This transmitter includes a clip you can wear over a pocket/belt, or firmly fixed to a belt. Figure 7.1: Belt Clip Attachment 2014.03 | V1.0.
ALLPLEX track Personnel Transmitter Wearing the Transmitter | en 15 To wear the transmitter over a pocket/belt, secure the clip to the transmitter at the two top positions (no. 4) using the screws provided. To fix the transmitter firmly on a belt, secure the clip to the transmitter at the two top positions (no. 4), and at the bottom location (no. 5) using the screw that secures the battery door. The clip is designed to be worn on a security type utility belt.
en | Testing the Transmitter 8 ALLPLEX track Personnel Transmitter Testing the Transmitter Test your transmitter by standing within sight of a receiver or siren-strobe. While holding down the Test button, press the Alarm button until the transmitter emits 3 short beep tones. A test transmission is sent to the Central Console, lighting the green LED on a receiver or the strobe on an outdoor siren-strobe. There might be a brief delay of 2 to 3 seconds before the flashing light appears.
ALLPLEX track Personnel Transmitter 9 Upgrading Transmitter Firmware | en 17 Upgrading Transmitter Firmware Transmitter firmware can be upgraded wirelessly via a dedicated coordinator using the Utility Tool of the Security Escort software. For more information on the usage of Utility Tool, please refer to the Security Escort Installation and Setup Manual. Robert Bosch (SEA) Pte Ltd Installation Manual 2014.03 | V1.0.
Robert Bosch (SEA) Pte Ltd 11 Bishan Street 21 573943 Singapore Singapore www.boschsecurity.
