User Manual

ManualsBrandsBosch Rexroth Group ManualsOtherBODAS Pressure Sensor PR2

Table Of Contents

Linear Motion and

Assembly Technologies ServicePneumaticsHydraulics

Electric Drives

and Controls

BODAS

Pressure Sensor PR2

Technical data sheet

Thin film technology sensor to measurement pressure

Series 10

Features

– Measurement range to 160, 250, 400, 600 bar

– Shock and vibration resistant

– Type of protection IP67 to IP69K

– Electric connection versions: male connector or cable

– Ratiometric output signal 0.5..4.5V

@ 5V

– Additional versions upon request

Position Foto

(oben links):

X = 147

Y = 93,9

RE 95 138/01.07 1/8

replaces: 01.05

Inhalt

Ordering Code 2

Description

Technical Data

Dimensions

Pin Assignment

Mating Connector

Commissioning / Service

Summary of content (8 pages)

PAGE 1
Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics BODAS Pressure Sensor PR2 Service RE 95 138/01.07 replaces: 01.
PAGE 2
/8 Bosch Rexroth AG PR 2 RE 95 138/01.07 Ordering Code BODAS – PR2 / 01 02 03 04 05 10 06 Type 01 BODAS Pressure sensor 02 03 PR2 Pressure range 0 .. 160 bar -160 0 .. 250 bar -250 0 .. 400 bar -400 0 .. 600 bar -600 Mechanic connection (pressure side) G 1/4 in acc. to DIN 3852-E 160, 250, 400, 600  600 – G M 14x1,5 acc.
PAGE 3
RE 95 138/01.07 Bosch Rexroth AG PR 2 /8 Description This sensor serves for the measurement of pressure in hydraulic circuits. It is especially suited for use in mobile hydraulics due to its excellent features. Shock and vibration resistance, type of protection, resistance to pressure peaks, resistance to temperature shock, EMC characteristics (up to 100 V/m). The measuring principle uses a hermetically welded thin film measuring cell which provides long-term density.
PAGE 4
/8 Bosch Rexroth AG PR 2 Dimensions RE 95 138/01.07 Dimensions in millimeters Electric connection DEUTSCH DT04-3P 46.1 ca. 56 Ø20.2 Ø20.2 12 Max. 30 Nm G1/4A 22 Max. 30 Nm 11 2 22 2.5 ca. 60 ca. 52 3.5 AMP Superseal DIN 3852-E Ø18.9 M14x1.5 ISO 6149-2 67 Cable output Ø20.2 Mechanic connection G1/4 to DIN 3852-E M14x1,5 to ISO6149-2 G1/4A 11 12 20.2 Seal ring 16.5x11.6x1.5 2.5 22 22 M14x1.
PAGE 5
RE 95 138/01.
PAGE 6
/8 Bosch Rexroth AG PR 2 Mating Connector Order designations for mating connector Type AMP Superseal Designation Material numbers Mating connector set R902602132 1x female connector housing 3-pin AMP 282087-1 3x single-wire seals, yellow AMP 281934-2 3x female connector contacts 1,8-3,3 mm AMP 183025-1 Type DEUTSCH DT04-3P Designation Material numbers Mating connector set R902603524 1x housing 3-pin DT06-3S-EP04 1x chock W3S 3x female connector 0462-201-16141 The mating connectors ar
PAGE 7
RE 95 138/01.07 PR 2 Bosch Rexroth AG /8 Commissioning / Service General: The described pressure sensors are designed and produced according to the latest technology. All components are subject to the strictest quality criteria during production. Note: Please inspect the device for any damages which may have occurred during transport. If there are obvious signs of damage, please immediately inform the transport company and Rexroth.
PAGE 8
/8 Bosch Rexroth AG Bosch Rexroth AG Hydraulics Product Segment Mobile Electronics Robert-Bosch-Straße 2 71701 Schwieberdingen, Germany Phone +49 (0) 711 811 –4 30 80 Fax +49 (0) 711 811 –3 36 85 info.brm-me@boschrexroth.de www.boschrexroth.com/mobile-electronics PR 2 RE 95 138/01.07 © This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be reproduced or given to third parties without its consent.