Datasheet

18 | English
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or to
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs Capacity
3× continuous green light 60−100%
2× continuous green light 30−60%
1× continuous green light 5−30%
1× flashing green light 0−5%
Battery model ProCORE18V...
LEDs Capacity
5× continuous green light 80−100%
4× continuous green light 60−80%
3× continuous green light 40−60%
2× continuous green light 20−40%
1× continuous green light 5−20%
1× flashing green light 0−5%
Inserting/changing the saw blade
u When fitting or changing the saw blade, wear protect-
ive gloves. Blades are sharp and can become hot when
used for prolonged periods of time.
Selecting the saw blade
You will find an overview of recommended saw blades at the
end of these operating instructions. Only use saw blades
with single lug shank (T shank). The saw blade should not be
longer than required for the intended cut.
Use a narrow saw blade when sawing tight curves.
Inserting the saw blade (seefigure A)
u Clean the shaft on the saw blade before inserting it.
Adirty shaft cannot be securely fixed in place.
Push the saw blade (10), with the teeth in the cutting direc-
tion, into the saw blade receptacle (17) until it clicks into
place. The SDS lever (11) automatically springs back and
the saw blade is locked in place. Do not push the lever (11)
back by hand as you could damage the power tool.
Make sure when inserting the saw blade that the back of the
saw blade is in the groove on the guide roller (9).
u Check that the saw blade is seated securely. A loose
saw blade can fall out and lead to injuries.
Ejecting the saw blade (seefigure B)
u When ejecting the saw blade, hold the power tool in
such a manner that no persons or animals can be in-
jured by the ejected saw blade.
Turn the SDS lever (11) as far as it will go in the direction of
the shock protection guard (13). The saw blade is released
and ejected.
Glide shoe (see figure C)
The plastic guide plate(6) of the base plate(7) reduces
scratching on sensitive surfaces. Use the steel glide
shoe(18) when machining metal.
Fit the steel glide shoe(18) by sliding it onto the base
plate(7) from the front.
The plastic guide plate(6) should be replaced if it is worn.
Anti-splinter guard (see figureD)
The anti-splinter guard (19) (accessory) can prevent splin-
tering of the surface while sawing wood. The anti-splinter
guard can only be used with certain saw blade types and only
at a cutting angle of 0°. When sawing with the anti-splinter
guard, the base plate (7) must not be moved to the rear for
sawing close to edges.
Slide the anti-splinter guard (19) into the base plate (7)
from the front.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
u Avoid dust accumulation at the workplace. Dust can
easily ignite.
Connecting the dust extraction (see figures E–F)
Fit the extraction outlet(20) in the recesses of the base
plate(7).
Connect a dust extraction hose (21) (accessory) to the ex-
traction outlet (20). Connect the dust extraction hose (21)
to a dust extractor (accessory).
You will find an overview of connecting to various dust ex-
tractors at the end of these operating instructions.
1 609 92A 65M | (24.11.2020) Bosch Power Tools