Installation Manual
Table Of Contents
- Cooktop
- Table of ContentsInstallation instructions
- Appliance Handling Safety 3
- Safety Codes and Standards 3
- Electric Safety 3
- Related Equipment Safety 3
- Proposition 65 Warning: 3
- Tools and parts needed 4
- Parts included 4
- Cabinet Requirements 4
- Countertop Requirements 4
- Cutout dimensions for 30" cooktops 5
- Cutout dimensions for 36" cooktops 5
- Secure the cooktop to countertop 6
- Electrical requirements 7
- Connect Electrical Supply 7
- Check the Installation 7
- 9 Safety DefinitionsSafety Definitions
- IMPORTANT SAFETY INSTRUCTIONS
- Table des matièresNotice de montage
- Sécurité de manutention des appareils 10
- Codes et normes de sécurité 10
- Sécurité électrique 10
- Équipement de sécurité 10
- Avertissement issu de la proposition 65 10
- Outils et pièces nécessaires 11
- Pièces comprises 11
- Exigences pour les placards 11
- Exigences pour le plan de travail 11
- Dimensions de la découpe pour tables de cuisson de 30 po 12
- Dimensions de la découpe pour tables de cuisson de 36 po 12
- Fixer la plaque au plan de travail 13
- Critères électriques 14
- Brancher l'alimentation électrique 14
- Vérification de l'installation 14
- 9 Définitions de sécuritéDéfinitions de sécurité
- CONSIGNES DE SÉCURITÉ IMPORTANTES
- LIRE ET CONSERVER CES INSTRUCTIONS
- Avant de commencerAvant de commencer
- Préparation des meublesPréparation des meubles
- Procédure d'installationProcédure d’installation
- Installation électrique
- Service technique
- ÍndiceInstrucciones de instalación
- Seguridad de manejo del electrodoméstico 17
- Códigos y normas de seguridad 17
- Seguridad eléctrica 17
- Seguridad del equipo relacionado 17
- Advertencia en virtud de la Proposición 65 18
- Herramientas y piezas necesarias 19
- Piezas incluidas 19
- Requisitos de gabinetes 19
- Requisitos de la superficie de trabajo 19
- Dimensiones del hueco para placas de 30 in 20
- Dimensiones del hueco para placas de 36 in 20
- Asegure la placa a la superficie de trabajo 21
- Requisitos eléctricos 22
- Conexión de la alimentación eléctrica 22
- Pruebe la instalación 22
- 9 Definiciones de seguridadDefiniciones de seguridad
- INSTRUCCIONES DE SEGURIDAD IMPORTANTES
- LEA Y CONSERVE ESTAS INSTRUCCIONES
- Antes de empezarAntes de empezar
- Preparación de los muebles de montajePreparación de los muebles de montaje
- Procedimiento de instalaciónProcedimiento de instalación
- Instalación eléctrica
- Servicio técnico
7
Electrical Installation
Electrical requirements
You can find the identification plate with the electrical
specifications on the underside of the appliance. The
junction box must be located within 3feet of the cooktop
connection. It should be easily accessible for service
purposes.
Refer to data plate for more information. See “Data Plate”
under “Service” for data plate location.
Power supply
Connect Electrical Supply
9 WARNING
Before installing, turn off at the service panel. Lock
service panel to prevent power from being turned
on accidentally.
The electrical power supply system should be a 1-phase,
3-wire system with ground connection. Install suitable
junction box (not furnished). An appropriately-sized, UL-
listed conduit connector must be used to correctly attach
the conduit to the junction box.
The branch-circuit breakers ampacity, the wire sizes and
the connections must conform to the requirements of the
National Electrical Code or Canadian Electrical Code and
all local codes and ordinances.
Attach flexible conduit to the junction box.
Metal conduit and leads are factory installed.
9 WARNING
To reduce the risk of electrical shock and fire, do
not use a flexible power-supply cord with this
appliance. Connect only to a 3 wire, 120/240-volt
power supply; the neutral conductor is not required
for the operation of the appliance. The potential at
the power supply electrical connections shall be
150-volts-to-ground or less.
Connect the cooktop lead wires to the junction box
supply wires in proper phase:
black (L1) to black
red (L2) to red
green or blank copper wire to ground
Check the Installation
9 WARNING
Before you turn on power supply, make sure all
controls are in the OFF position.
Remove everything from the cooktop surface including
stickers. Clean cooktop surface with cooktop cleaning
cream.
Switch on the circuit breaker.
Verify that elements function properly.
Model 240V AC, 60Hz
system: circuit
breaker
208V AC, 60Hz
system: circuit
breaker
NET8068SUC 40Amp 30Amp
NET8068UC 40Amp 30Amp
NET8668SUC 50Amp 40Amp
NET8668UC 50Amp 40Amp
NETP068SUC 40Amp 40Amp
NETP668SUC 40Amp 40Amp
NEM5066UC 30Amp 30Amp
NEM5666UC 40Amp 40Amp
PP
PP
-ER[
&RQGXLWDSSUR[
IHHWaPP
PP
)LWWLQJ&RQGXLW
PP
DSSUR[










