EN Operating and installation instructions PKFI11, PKFI11AB BORA Pro surface induction glass ceramic cooktop with 2 cooking zones BORA Pro surface induction glass ceramic cooktop with 2 cooking zones All Black PKFI11UMEN-007 www.bora.
Operating and installation instructions: Original Translation Manufacturer BORA Vertriebs GmbH & Co KG Innstraße 1 6342 Niederndorf Austria Contact T +43 (0) 5373 / 62250-0 mail@bora.com www.bora.com The distribution and duplication of this document, as well as the use and disclosure of its contents are prohibited unless expressly authorised. These operating and installation instructions have been drawn up with the greatest of care.
EN Table of Contents 1 General information 4 1.3 1.4 Target group......................................................... 4 Validity of the operating and installation instructions.......................................................... 4 Other applicable documents................................ 4 Presentation of information.................................. 5 2 Safety 6 1.1 1.2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 3 4 General safety instructions..................................
General information EN 1 General information 1.1 Target group INFO These operating and installation instructions apply for the following target groups: Target group Requirements User The appliance can be used by children aged 8 and above as well as people with reduced physical, sensory or mental capacities or a lack of experience and/or knowledge if they are supervised or have been instructed how to safely use the appliance and understand the resultant risks. Children must be supervised.
General information 1.4 EN Presentation of information To make working with these instructions quick and easy, consistent formatting, numbering, symbols, safety instructions, terms and abbreviations are used throughout. Handling instructions are market with an arrow. XX Always carry out handling instructions in the sequence shown. Bullet points are indicated by a square bullet point at the edge of the line.
Safety EN 2 Safety 2.1 General safety instructions INFO QQ The The appliance complies with the stipulated safety requirements. The user is responsible for appliance cleaning and maintenance as well as its safe use. Improper use can lead to personal injury and damage to property. operating and installation instructions contain important information about installation and operation. These enable you to protect yourself against injuries and prevent damage to the appliance.
Safety XX When using recirculation mode, ensure a sufficient supply of fresh air, e.g. by opening a window. XX Ensure a normal and comfortable room climate (humidity of 45–60%), e.g. by opening natural ventilation openings or using domestic ventilation systems. XX After every use in recirculation mode, switch the cooktop extractor to a low level for about 20 minutes or activate the automatic after-run function. Faults and errors XX Observe the information in the Troubleshooting chapter.
Safety EN WARNING! Risk of burns from hot objects! The cooktop and its exposed parts are hot when the cooktop is in use and during the cooling phase. Objects on the cooktop heat up very quickly and can cause serious burns. This particularly applies to metal objects (e.g. knives, forks, spoons, lids or cooktop extractor covers). XX Do not place any items on the cooktop. XX Please use suitable tools (pot holders, oven gloves).
Safety 2.3 Safety Instructions – Installation DANGER! Risk of electric shock! The connection cable can be damaged if it comes into contact with hot cooking zones. A damaged connection cable can cause a (fatal) electrical shock. XX Make sure that the connection cable does not come into contact with hot cooking surfaces. XX Make sure that the connection cable does not become trapped or damaged.
Safety EN 2.5 Safety instructions – disassembly and disposal The appliance must only be disassembled by trained specialists who are familiar with and comply with the standard national regulations and supplementary regulations of the local utility companies. Work on electrical components must only be conducted by trained electrical personnel. DANGER! Risk of electric shock! Incorrectly disconnecting the appliance from the mains results in a risk of electric shock.
Technical data Technical data Device dimensions cooktop Value 370 Supply voltage 220 - 240 V 230 Frequency 50/60 Hz Power consumption 3.7 kW Fuse protection 1 x 16 A Dimensions (width x depth x height) 370 x 540 x 52 mm Weight (incl. accessories/ packaging) 8.
Device description EN 4 Device description 5 Observe all safety and warning information during operation (see the Safety section). Fig. 4.2 [1] [2] [3] [4] [5] 2 2 Structure of control knob Knob casing Universal nut Control knob display knob ring Wave spring 4.
Device description Knob operation All the cooking zones are controlled using a control knob. By twisting the control knob and pressing the touch surface, the power levels and functions for the relevant cooking zone are controlled (see Operation section). 7-segment display Display Meaning 0 1 –9 ßp v , /: /* A % H EN 4.3.1 Power levels The high power output of induction cooktops results in the very quick heating up of cookware.
Device description EN 4.3.3 Automatic heat up function The two cooking zones are equipped with an automatic heat up function that can be switched on and off. QQ A is displayed. This function enables the cooking zone to work at full power for a certain duration after switching on. After this time, the power level is automatically switched back to the power level set. Power level Cooking duration in min:sec 1 2 3 4 5 6 7 8 0:40 Tab. 4.
Device description 4.3.8 Timer functions There are two different timer functions for each cooking zone. QQ t appears in the control knob display. INFO You can set a time range of between 1 and 120 minutes for the timer functions. Timer function INFO The timer function is an automatic cut-off which automatically switches off a cooking zone which is in use. Short-time timer (egg timer) INFO The short-time timer requires the cooking zone to be switched off and works like a conventional egg timer. 4.3.
Installation EN 5 Installation 5.3 XX Observe all safety and warning information (see the Safety chapter). XX Follow the enclosed manufacturer’s information. INFO The cooktop must not be installed above cooling devices, dishwashers, stoves, ovens, washing machines or driers. INFO The contact surface of the worktops and wall sealing strips must be made of a heat-resistant material (up to approx. 100 °C).
Installation x R5 ≥60 Fig. 5.4 14 (≥74) ≥ 700 Groove dimensions for flush installation Cut-out dimensions when installing cooktops or cooktops and the cooktop extractor next to each other: Cooktops/cooktop extractor Worktop overhang XX Please note the worktop overhang x when creating the worktop cut-out. Applicable to flush installation and surface mounting. Tab. 5.2 www.bora.com 14 7 +0,5 All dimensions are shown from the front edge of the front cover.
Installation EN 5.5 5.4.2 Surface mounting x ≥ 74 516 ±2 R5 Fig. 5.5 ≥ 700 ≤ (≥ 70) B ±2 Installing the cooktop INFO Clearance of one millimetre should be planned between the built-in appliances. INFO A clearance of two millimetres should be planned around the built-in appliances. INFO It is recommended to install a mounting rail between adjacent cooktops (mounting rail PZMS available as an accessory). INFO Alternatively, the cooktop can be fitted rotated by 180°. 5.5.
Installation 4 1 3 Fig. 5.9 [1] [2] [3] [4] INFO 2 Structure of control knob Knob casing Universal nut knob ring Wave spring The wave spring must not be used with steel fronts. The relevant assembly steps should simply be skipped. XX Pull off the knob ring [3]. XX Unscrew the universal nut [2]. XX Pull off the wave spring [4]. XX Push the knob casing [1] through the hole in the panel from the front. XX Push the wave spring [4] onto the knob casing [1] from the rear (not with steel fronts).
Installation EN 1 370 1 1 110 370 1 110 370 1 Ø5 0 ±0 ,5 ≥70 ≥40 2 Fig. 5.15 90 90 196 Fig. 5.13 [1] [2] [3] [4] [5] [6] 196 90 196 196 90 90 Bore holes for 3 cooktops and 2 cooktop extractors [1] [2] Cooktop and height adjustment plates Cooktop Height adjustment plates XX If applicable, insert the height adjustment plates [2]. Boreholes for socket (2x external) Bore holes for control knobs (8x) Cooktop (3x) Cooktop extractor (2x) Worktop Floor unit front panel 1 5.5.
Installation 5.5.4 Establishing communication The appliance components are linked by the ribbon cable provided. XX Create the connection between the cooktop and the control knobs. XX Create the connection between the cooktop and the cooktop extractor. Standard cooking zone connection 1 2 3 Cooking zone connection INFO EN 4 According to the default settings, the left control knob operates the front cooking zone and the right control knob operates the rear cooking zone.
Installation EN Connecting the cooking zones when the cooktop is installed rotated by 180° Connecting the automatic extraction system 2 1 1 ZONE1 INTERF. COM1 ZONE2 2 7 6 ZONE1 INTERF. COM1 ZONE2 3 3 Fig. 5.21 [1] 5 Fig. 5.
Installation XX Switch off the main switch/automatic circuit breaker before connecting the cooktop. XX Secure the main switch/automatic circuit breaker against being switched back on without permission. XX Make sure the power to the appliance is disconnected. XX Only connect the cooktop using a permanent connection to a power supply cable. 1 2 L1 N PE 220 - 240 V~ Fig. 5.22 Connection diagram 1-phase XX Check that installation has been carried out correctly.
Installation EN Availability of the pause function Once you have confirmed menu option C 9 , you can permanently deactivate the pause function. Setting Pause function available/deactivated C 90 C9 1 C 92 Pause function activated Factory setting Pause function deactivated Pause function with power level display activated Tab. 5.9 Availability of the pause function 5.6.3 Changing the set value XX Turn the knob ring clockwise to increase the value.
Operation 6 Operation 6.2 XX Observe all safety and warning information during operation (see the Safety section). INFO The cooktop may only be operated when the stainless steel grease filter of the cooktop extractor is installed (see operating instructions for cooktop extractor). INFO Clean the cooking zone before using the cooktop for the first time (see the Cleaning section). General operating instructions The cooktop is controlled using the control knobs.
Operation EN 6.2.3 Bridging function INFO If the bridging function is active, both cooking zones will operate at the same time on the same cooking zone. INFO If the bridging function is activated, the power setting ßp cannot be used. Switching on the bridging function Both control knobs are in the 12 o’clock position. XX Press the touch surface on both control knobs at the same time for at least 1 second. QQ The left control knob display and the front cooking zone indicator show % .
Operation Increase heat retention level XX Press the touch surface on the control knob a second time for 1 second to activate heat retention level 2 ( : ). XX Press the touch surface on the control knob a third time for 1 second to activate heat retention level 3 ( * ). QQ This is always confirmed with an acoustic signal and the corresponding symbol is displayed. Reduce heat retention level QQ After setting heat retention level 3, pressing the touch surface (1 second) again reduces the level by 1.
Operation EN Activating the short-time timer (egg timer) XX Once you have confirmed the time set, you have 3 seconds to turn the knob ring to the 12 o’clock position. QQ This activates the short-time timer and the time starts to count down. QQ The displays shows remaining time (accurate to the minute for more than 2 minutes and accurate to the second for under 2 minutes). QQ At the end of the time, a beep sounds for 2 minutes and the control knob display flashes 0 0 0 .
Cleaning and Maintenance 7 Cleaning and Maintenance XX Observe all safety and warning information (see the Safety chapter). XX Follow the enclosed manufacturer’s information. XX When conducting scheduled cleaning and maintenance, ensure that the cooktop and cooktop extractor are fully switched off and cooled so as to prevent injury (see the Operation chapter). QQ Regular cleaning and maintenance ensures long service life of the product and optimal function.
Cleaning and Maintenance EN 7.4 Cleaning the control knobs 2 1 3 Fig. 7.5 [1] [2] [3] Pull out the knob ring Knob casing Touch surface Knob ring 7.4.1 Cleaning the knob ring The knob ring can only be cleaned by hand. XX Remove the knob ring from the knob housing. XX Use a cleaner and degreaser in one. XX Rinse the knob ring with hot water. XX Clean the knob ring with a soft brush. XX Rinse the knob ring well after cleaning. XX Dry the knob ring carefully.
Troubleshooting 8 EN Troubleshooting Observe all safety and warning information (see the Safety section). Operating situation Cause Remedy The cooktop cannot be switched on. Knob ring missing Place the knob ring on the control knob. The fuse or automatic circuit breaker of the electrical wiring system in the apartment and/or house is defective. Replace the fuse. The fuse or the automatic circuit breaker trips multiple times Contact BORA Service Team The power supply is disconnected.
Decommissioning, d isassembly and disposal EN 9 Decommissioning, disassembly and disposal XX Observe all safety and warning information (see the Safety section). XX Follow the enclosed manufacturer’s information. 9.1 Decommissioning Decommissioning is understood as final shutdown and disassembly. Following decommissioning, the device can either be installed into other units, sold on privately or disposed of. INFO Electricity and gas connections may only be disconnected by qualified specialists.
Warranty, technical service, spare parts, accessories 10 Warranty, technical service, spare parts, accessories XX Observe all safety and warning information (see the Safety chapter). 10.1 BORA manufacturer’s warranty BORA provides its end customers with a 2-year manufacturer’s warranty for its products. The end customer is entitled to this warranty in addition to the statutory claims for defects against the sellers of our products.
Notes EN 11 Notes 34 www.bora.
Notes www.bora.
Nameplate: (please affix) Germany: Europe: BORA Lüftungstechnik GmbH Rosenheimer Str. 33 83064 Raubling Germany T +49 (0) 8035 / 9840-0 F +49 (0) 8035 / 9840-300 info@bora.com www.bora.com BORA Holding GmbH Innstraße 1 6342 Niederndorf Austria T +43 (0) 5373 / 62250-0 F +43 (0) 5373 / 62250-90 mail@bora.com www.bora.com Austria: Australia - New Zealand: BORA Vertriebs GmbH & Co KG Innstraße 1 6342 Niederndorf Austria T +43 (0) 5373 / 62250-0 F +43 (0) 5373 / 62250-90 mail@bora.com www.bora.
