User Manual
EN
27
Appliance description
www.bora.com
4.4 Safety devices
4.4.1 Control lock
The control lock prevents unintentional use of the
cooktop extractor and cooktops during operation.
If the control lock is active, the symbol lights up.
The functions are locked and the indicators on the
display are dimmed (exception: power button).
4.4.2 Cleaning lock (wipe function)
The cleaning lock prevents settings from being changed
when wiping the operating panel during a cooking
session. Upon activation the operating panel is locked
for a certain time (factory setting 15 seconds). The
remaining time is displayed. All appliance settings remain
unchanged in the meantime.
The duration of the wiping time can be set in the menu
(5 – 30 seconds).
INFO If the operating panel is cleaned with a damp
cloth, a film of water may form and the power
button may be triggered despite the cleaning lock
being activated. This can be corrected by drying
the panel immediately after cleaning.
4.4.3 Safety shut-down
If the appliance is switched on but not used for 2 minutes,
it will automatically switch off (standby mode).
Cooktop extractor
The cooktop extractor will be automatically switched off
30 minutes after all cooking zones have become inactive
(= power level 0) and the automatic after-run function will
be started.
Cooktops
Each cooking zone is automatically switched off after a
predefined operating time in which the power level has
not been changed.
Power levels Safety shut-down after hrs:min
Cooktops CKFI,
CKI, CKIW, CKT
Cooktops CKCH,
CKCB
Cooktop
CKG
1
08:24 06:00 08:24
2
06:24 06:00 06:24
3
05:12 05:00 05:12
4
04:12 05:00 04:12
5
03:18 04:00 03:18
6
02:12 01:30 02:12
7
02:12 01:30 02:12
8
01:48 01:30 01:48
9
01:18 01:30 01:18
ßp
00:10 0:10 (only in the case
of CKCH)
00:20
Tab. 4.20 Safety shut-down for power levels
Warming level Safety shut-down after hrs:min
1 (
,
)
08:00
2 (
:
)
08:00
3 (
*
)
08:00
Tab. 4.21 Safety shut-down for warming levels
Switch the cooking zone back on if you want to put
the cooking zone back into operation (see Operation
chapter).
4.4.4 Residual heat indicator
H
If a cooking or grilling zone is still hot after switching off,
there is a risk of burns or fire. Whilst the hot symbol
and
H
are displayed (residual heat indicator), you must
not touch that cooking or grilling zone or place any heat-
sensitive objects on it. After a sufficient cooling period
(< 50 °C) the indicators will go out.
INFO During or after a power cut, the cooktops may
still be hot. In the case of the cooktops CKCH and
CKCB, no residual heat is displayed after a power
cut, even if they were in use beforehand and the
hobs are still hot.
4.4.5 Overheating protection
INFO If a cooktop overheats, its power is reduced or it
is switched off completely.
INFO If the operating panel overheats, cooktops or the
whole system may be switched off.
The appliances are fitted with overheating protection. The
overheating protection can be triggered if...
... cookware is heated up empty.
... oil or fat is heated on high power.
... a hot cooking zone is switched on again after a power
cut.
... hot cookware heats up the operating panel.
Whilst the overheating protection is active, one of the
following
steps is taken:
The activated power setting is switched back to the
previous level.
The set power level is reduced.
The cooking zone switches off completely.
The cooktop switches off completely.
The system switches off completely.
After a sufficient cooling period, the appliance can be
used again in full.
4.4.6 Childproofing feature
The childproong feature prevents the appliance from
being switched on accidentally or without permission.