Service manual

4. Temporarily install the right saddlebag into the support
assembly.
a. Confirm that the vehicle-side harness connectors
comfortably reach the saddlebag connectors.
b. Confirm that the amplifier harness connectors and
harness routing are clear of all moving parts.
c. Confirm that no contact is made at full extension and
compression of the shock absorber.
When sufficient clearance is confirmed, tighten the cable
straps. Remove the saddlebag.
NOTE
Continue routing the harness forward on the vehicle. Heed the
tips found at the beginning of this section.
5. Locate the black, four-way Molex connector [296A] near
the back of the underseat area.
FLHX/FLTRX models: On a jumper harness coming from
the fairing.
FLHTCU/FLHTK models: On an adapter harness with
two 16-way ([162C] and [162D]) and two four-way ([296A]
and (297B]) connectors.
With ONLY ONE Stage II amplifier installed in the rear:
Remove the plug in the [296A] connector. Connect the
amplifier harness.
With TWO or more Stage II amplifiers installed in the
rear: Plug the audio input harness (15) from this kit into
connector halves [296A] and (297B] on the adapter har-
ness. Plug amplifier harness connector [296A] into the
audio input harness.
6. Locate the gray six-way Data Link Connector (DLC) [91A]
in the electrical caddy.
a. Cut the tether attaching the weather cap around the
harness. Remove the cap.
b. Pull connector [91A] back through the electrical caddy
to a location under the seat, behind the caddy.
c. Plug in gray six-way socket connector [91B] from the
amplifier harness to connector [91A] under the seat.
d. Route gray six-way pin connector [91A] from the
amplifier harness into the electrical caddy.
e. Insert the weather cap removed in Step 6a into the
new pin connector [91A]. Use a cable strap (17) from
the kit to attach the tether to the harness.
NOTES
• If more than two amplifiers or other accessories already
use the ground post of the battery, use one of the frame
ground studs.
• If more than two amplifiers are installed on the vehicle, a
Battery+ Three-Way Y Connector (Part No. 70270-04A,
available separately) is required.
7. Route the battery terminal branch to the battery terminals,
but DO NOT connect the battery cables now.
8. Route the long harness branch forward, into the wire
trough, to the right side. At the front of the trough, route
the wires to the fairing lowers:
• Connectors [36RT] and [36RW] to the right lower fairing
speaker enclosure.
• Connectors [37LT] and [37LW] to the left lower fairing
speaker enclosure.
9. Get the two split rubber grommets (14) from the kit. Install
one grommet over each amplifier harness speaker wire
set.
10. Follow instructions in the Boom! Audio Fairing Lower
Speaker Kit for wiring hole location, drilling and completing
the installation.
SADDLEBAG WIRING
1. See Figure 9. Plug in connector [149] of the saddlebag
harness to the top of the amplifier. Route the saddlebag
side harness inside the left saddlebag.
Clean the inside bottom and side surfaces of the
saddlebag along the harness path with a 50-50 mixture
of isopropyl alcohol and distilled water. Secure with cable
straps and bases as shown.
1
2
4
3
is07753b
1. Amplifier harness connector
2. Wire harness
3. Wire harness cable strap
4. Wire harness
Figure 9. Inner Harness Routing
2. Saddlebag liners (if present): Trim saddlebag liners.
Install saddlebag liners.
3. See Figure 10. Install the amplifier cover on the bracket.
Secure with three clips.
5 of 8-J06051