READ BEFORE USE! Model No.: HYPH4601-4 Item No.
General Safety Information This manual contains important information about the assembly, operation and maintenance of this heater. General safety information is presented in these first few pages and is also located throughout the manual. Keep this manual for future reference and to educate new users of this product. This manual should be read in conjunction with the labeling on the product. Safety precautions are essential when any mechanical or propane fueled equipment is involved.
Never store propane near high heat, open flames, pilot lights, direct sunlight, other ignition sources or where temperatures exceed 120 (49 ). Propane is heavier than air and can accumulate in low places. If you smell gas, leave the area immediately. Never install or remove propane cylinder while heater is lighted, near flame, pilot light, ignition sources or while heater is hot touch. This heater is red hot during use and can ignite flammables too close to the heater.
sides 24 in /60.9 cm. 24 in/60.9cm 4 24 in /60.9 cm and 24 in /60.
A Tank Housing 1 B Burner 1 C Glass Tube 1 D Glass Tube Ring 1 E Mesh Guard 3 F Upper Supporter 3 G Upper Combination 1 H Tank Housing Supporter 1 I Wheel 1 J Handle 1 K M5x12 screw 6 Attached into the upper supporter L M4x10 screw 3 Attached into the burner cover M M5x12 screw 6 in hardware packing 5
N M5 lock nut 4 in hardware packing O M8x16 screw 3 1 in hardware packing, 2 screwed into wheel P M8 lock nut 2 screwed into wheel Q M6 nuts 1 assembled into handle R M6 washer 1 assembled into handle S M6x12 screw 6 in hardware packing T M6 lock nut 6 in hardware packing U Anchoring Arm 3 in hardware packing V Anchoring Nut 3 in hardware packing W Wrench 1 in hardware packing 6
Step 1:Unscrew the handle nuts (Q)and washer(R) and assemble the handle into tank housing(A). 1-1 1-2 1-3 Step 2: Unscrew the wheel screws (O) and nuts (P) and assemble the wheel (I) into tank housing base. 2-1 2-2 2-3 Step 3:Use the M8x16 screw (O) and M5x12 screw(M) from the hardware packing to attach the tank housing supporter(H) into the base hole and the tank housing and don’t fasten them.
4-4 Step 9:Put the upper combination(G) into the supporter and glass tube to make sure the three holes match up and use screws (from Step 7) to fasten them. 4-5 9-1 9-2 9-3 Step 5:Use 1pc M5x12 screw (M) to fasten the tank housing supporter. 5-1 9-4 5-2 Step 10:Assemble three mesh guards(E) into the upper supporter hook. Caution: Ensure t he mesh guard is in the correct position. (10-3) Step 6:Screw off 3pcs M4x10 screws(L) from the burner cover and attach the glass tube ring(D) into it.
Connect Hose & Regulator to Cylinder Step 1 - Gas Cylinder Required ■ You must provide propane gas and propane cylinder. Use a standard 20lb propane cylinder only. ■ Use this heater only with a propane vapor withdrawal supply system. See chapter 5 of the Standard for Storage Figure 1 20LB Propane Cylinder and Handling of Liquefied Petroleum Gas, ANSI/ NFPA 58. Your local library or fire department will have this book. ■ Maximum supply pressure of 250 psi.
This appliance shall be used only in a wellventilated space and shall not be used in a building, garage or any other enclosed area. This appliance may be installed with shelter no more inclusive than: 1. With walls on all sides, but with no overhead cover. 2. Within a partial enclosure which includes an overhead cover and no more than two side walls. These side walls may be parallel, as in a breezeway, or at right angles to each other. 3.
IF YOU HAVE QUESTIONS OR CONCERNS PLEASE CALL BOND TOLL FREE # 1-866-771-BOND(2663) OR TO BETTER EXPEDITE YOUR REQUEST FEEL FREE TO EMAIL US customer.service@bondmfg.com OR VISIT OUR WEBSITE UNDER CUSTOMER SERVICE SUPPORT www.bondmfg.com BOND MANUFACTURING CO.
