Technical data

Bona Sport
®
Sport Poly
Technical data sheet
Rev 11 /10
This data sheet replaces all previous versions page 2/2
Vacuum thoroughly. 4. Tack with mineral spirits. 5. Apply sealer and finish system (see finish
directions).
THE BONA SPORT
®
SPORT POLY SYSTEM: Bona Sport Poly is a 4 - coat system, 1 - 2 coats of a
Bona oil - modified sport sealer, CourtLines paint (if desired) and 2 - 3 coats of Bona Sport Poly.
RECOMMENDED APPLICATORS: Heavy weight T - bar, Lambs wool applicator.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: Remove lid and stir thoroughly before using. DO NOT THIN.
FINISHING: 1. Apply Bona Sport Poly with a heavy weight T- bar applicator. Go with the grain of
the wood applying a thin, uniform coat. 2. BE SURE YOU ARE USING THE RECOMMENDED
COVERAGE OF 600 SQ FT PER GALLON. 3. Avoid leaving puddles of excessive amounts of
finish on the floor. 4. Allow first coat to dry thoroughly (approximately 12 - 16 hours). High humidity
and/or low temperature conditions will extend dry time while increased ventilation and airflow will
reduce dry time (recommended conditions of 65 - 80 °F (18° - 27 ° C)/40 - 60% relative humidity). 5. For
proper adhesion, abrade between coats of finish. Allow final coat to dry a minimum of 72 hours
before use.
INTERCOAT ABRASION FOR FLOORS WITH GAMELINES: See sealer instructions for proper
sequence of sealer, gamelines and finish coats. Before applying gamelines, abrade with 120 - grit
screens and vacuum and tack thoroughly. Note: If paint will not be applied for 24 hours or longer,
fl oor must be re - abraded to ensure proper adhesion. Apply gamelines using Bona CourtLines
®
sport floor paint. IF USING ANOTHER MANUFACTURER’S PAINT, BEFORE APPLYING
GAMELINES, ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE
COMPATIBILITY AND ADHESION. Afte r applying gamelines using CourtLines
®
paint, once per
day, abrade entire floor with Bona
®
Conditioning Pads or used 120 or 150 grit screens. Always
vacuum and tack thoroughly after abrading. Apply finish coat within 24 hours.
INTERCOAT ABRASION FOR FLOOR S WITHOUT GAMELINES: Abrade between all sealer and
finish coats using Bona Conditioning Pads or 120 to 150 grit screens to ensure adhesion. Always
vacuum and tack thoroughly after abrading.
RECOATING: Be sure floor is free from wax, polish and oily residu es. Follow the Bona Prep
®
system, applying 1-2 coats of Bona Sport Poly. Delamination can occur if the Bona Prep process is
not followed; always test for compatibility.
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH BONA SPORT POLY MAY
SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY AFTER EACH
USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED, WATER - FILLED METAL
CONTAINER.
CURING: The curing process takes approximately 14 days. The floor may be walked on after 24
hours, but the floor is susceptible to scuffing or marring prior to completion of the curing time. Do
not replace athletic or walk - off mats until finish is fully cured. Do not clean with water or detergent
during the curing process.
CLEAN - UP: Clean appli cation tools and equipment with mineral spirits.
MAINTENANCE: Put walk - off mats at all entrance doorways to keep out excessive dirt and grit.
See Bona
®
Professional Series Sport and Commercial Cleaner Concentrate instructions for
cleaning and maintenance information.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100 ° F (38° C). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material . Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
Item# Size #/Case
ST750055111 5 Gallon 1
Order Information
Maintenance
Finishing