Technical data

ManualsBrandsBona ManualsBusiness equipmentMiniEdge

Bona Remover

™

Technical data sheet

Rev

/11

This data sheet replaces all previous

versions

page

1/2

Coatings

Part

of the Bona Recoat System

™

, Bona Remover is formulated to break down contamina

known to cause finish adhesion issues, such

as acrylic polishes, waxes, oil soaps, over

spray from

furniture cleaners/dusters, and any other contamina

nts

on a polyurethane finished wood floor or a

pre

finished wood floor. Bona Remover

™

also aides in abrading the wood floor to maximize

adhesion of B

ona Traffic

GREENGUARD Indoor Air Quality Certified

Non

flammable

Non

toxic

hour meter

Physical

Characteristics:

Ingredients

– Water, ethoxylated alcohol, Diethylene glycol ether, phenoxyethanol, and

Dipropylene Glycol n

butyl ether.

Color

–

Beige

–

Solids

Density – 9.

5 lbs./gallon (1.1

S.G.)

VOC

–

Odor

–

Slight solvent

Stabil

ity –

1 year shelf life

Packaging

–

1 gallon plastic bottle

Application Characteristics:

Application Tools

–

Bona

Roller

All types of residential and commercial polyurethane finished wood floors

Pre

finished, aluminum

-o

xide floors

BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.

MIXING INSTRUCTIONS:

Shake product vigorously for 15

20 seconds or until all settled product is

thoroughly mixed.

APPLICATION

DIRECTIONS:

Prior

to application, protect surrounding areas using blue tape

and/or plastic sheeting or trowels to prevent possible staining from accidental contact with Bona

Remover. In the event of a spill, immediately wipe up affected area using a clean towel and water.

Pour a 4” wide line of Bona Remover along starting wall.

Saturate the roller with product from

the pour line. Set roller down at back side of puddle and pull the roller towards you approximately

5 feet. Then push back in the same path beyond your o

riginal start point. BE SURE YOU ARE

USING THE RECOMMENDED COVERAGE OF 400

–

500 SQ. FT. PER GALLON. DO NOT

SPREAD TOO THIN. DO NOT COVER MORE FLOOR THAN YOU WILL BE ABLE TO ABRADE

AND RINSE IN 20

30 MINUTES (APROXIMATELY 200 SQ FT).

Using a 175rpm rota

ry buffer,

equipped with the Bona recoat abrasive drive plate, abrade the section of floor coated with Bona

Remover. Abrade with the grain up and back over the same path. Start the next pass by

overlapping the previous pass by 50%.

Hand

abrade any corne

rs and sections missed by the

buffer with 120 grit paper.

Using a window squeegee, squeegee Bona Remover material out

from the wall.

Using the Bona PowerScrubber

™

filled with

Bona Rinse (refer to Bona Rinse

directions for mixing instructions), remove

and clean all Bona Remover from floor.

Repeat steps

1 through 6 until entire floor has been treated.

TO GUARANTEE ALL CONTAMINATES HAVE

BEEN REMOVED AND MEET THE BONA RECOAT SYSTEM WARRANTY, IT IS REQUIRED

THAT THE ENTIRE FLOOR BE PREPARED A SECOND

TIME FOLLOWING STEPS 1

–

(DURING SECOND PASS IT IS NOT NECESSARY TO HAND ABRADE).

Using a clean terry

towel or microfiber cloth and warm water, wipe down the perimeter of the floor, approximately 1”

out from the wall where the Bona PowerScrubber could

reach. It may also be necessary to wipe

down all the baseboards and any other areas Bona Remover has come in contact with.

10.

Relocate buffer, Bona recoat abrasive drive plate, applicators and all other equipment besides the

Bona PowerScrubber from the floor. Thoroughly clean with water the Bona PowerScrubber

brushes, squeegees, power cord and your shoes/work boots of any remaining Bona Remover.

Perform a final “Rinse” step on the entire floor using the Bona PowerScrubber and Bona Rinse.

This step will he

lp ensure the floor is clean of any Bona Remover due to foot prints or missed areas

Directions

Technical data

Recommended Use