Technical data

Woodline
®
350 Polyurethane
Technical data sheet
Rev 11 /10
This data sheet replaces all previous versions page 2/2
Finishing
Brush on a buffer and vacuum thoroughly. 4. Tack with a dry Bona
®
Microfiber Mop or cloth to
remove dust. 5. Apply finish system.
THE BONA WOODLINE
®
350 POLY SYSTEM: Bona Woodline 350 Poly is a 3 - coat system. For
an unstained f loor, apply 1 coat of Bona
®
Drifast
®
Sealer according to label directions, followed by
2 coats of Bona Woodline 350 Poly. For a stained floor, apply a Bona
®
Drifast
®
Stain according to
label directions, followed by 2 coats of Bona Woodline 350 Poly. Adding a third coat of Bona
Woodline 350 Poly is recommended in heavy - traffic commercial and residential areas. Visit
www.bona.com for additional product information.
RECOMMENDED APPLICATORS: Lambswool applicator, natural bristle brush, snowplow tool,
flocked f oam paint pad and roller.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: STIR WELL BEFORE USE. DO NOT THIN.
FINISHING: 1. Apply Bona Woodline 350 Poly going with the grain of the wood. 2. Be sure to
feather out each stroke to avoid applicator marks. 3. BE SURE YOU ARE USING THE
RECOMMENDED COVERAGE OF 500 SQ FT PER GALLON. 4. Allow each coat to dry
thoroughly (approximately 8 - 12 hours). High humidity and/or low temperature conditions will extend
d ry time while increased ventilation and airflow will reduce dry time (recommended conditions of
65 - 80 °F (18°C - 27 ° C)/ 40 - 60% relative humidity). 5. Abrade in - between all coats with a 120 – 150
grit screen or maroon pad. 6. Thoroughly vacuum and wipe with a clean, lint - free, water dampened
cloth between coats of finish. If desired, a third coat may be applied. Allow final coat to dry a
minimum of 24 hours before use and avoid heavy traffic for 72 hours.
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep
®
system, applying 1- 2 coats of Bona Woodline 350 Poly. If Recoating a Factory Prefinished Floor,
DO NOT USE Bona Woodline 350 Poly. Use Bona Naturale
®
or Bona Traffic
®
finishes with the
Bona Prep system. Delamination can occur if the Bona Prep process is not followed and the floor
has not been tested for compatibility.
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH BONA WOODLINE
POLYURETHANE MAY SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED.
IMMEDIATELY AFTER EACH USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED,
WATER - FILLED, METAL CONTAINER.
CURING: The curing process takes approximately 14 days. The floor may be walked on after 24
hours, but the floor is susceptible to scuffing or marr ing prior to completion of the curing time.
Furniture may be placed onto floor after 72 hours (90% cured). Do not drag or slide furniture. Do
not replace walk - off mats until finish is fully cured. Do not clean with water or detergent during the
curing proc ess. Use only a dry cloth for cleaning during the first two weeks.
CLEAN - UP: Clean application tools and equipment with mineral spirits.
FLOOR CARE: Maintain your hardwood floor with Bona
®
Professional Series floor care products.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100º F (38º C). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material. Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
Item # Size / Sheen #/Case
ST750018113 Gallon – Gloss 4
ST750318115 Gallon – Semi - Gloss 4
ST750618133 Gallon – Satin 4
Order I nformation
Maintenance