Technical data

Bona Traffic
®
Anti Slip
Technical data sheet
Rev 05/11
This data sheet replaces all previous versions page 2/2
Finishing
MIXING INS TRUCTIONS: SHAKE WELL BEFORE USING. DO NOT THIN. DO NOT ADD WATER. 1.
Shake Bona Traffic Anti - Slip finish (Part A) well for 30 seconds. 2. Add Bona Traffic Hardener (Part B) to
finish (Part A). One 12.8 oz. bottle of hardener will activate one gallon of fi nish. To mix finish amounts of
less than one gallon, use a 1:10 ratio. 3. Immediately shake mixture vigorously for 30- 45 seconds. 4.
Insert supplied filter into bottle only after adding hardener. 5. Let sit for 5 - 10 minutes before applying.
BONA TRAFFIC AN TI - SLIP CANNOT BE REHARDENED.
FINISHING: 1. Pour a 6” wide line of finish along the starting wall. Go with the grain of the wood.
2. Using a pre - dampened applicator, draw the applicator forward with the grain of the wood, moving the
finish toward the opp osite wall. To maintain a wet edge at all times, hold the applicator at a snowplow
angle. 3. At the end of each run, turn the applicator towards you and pad out the applicator parallel to the
wet edge. 4. Feather out all turns. Do not push too hard or too fast to avoid drips flying off the applicator.
5. BE SURE YOU ARE USING THE RECOMMENDED COVERAGE OF 350 - 400 SQ. FT. PER GALLON.
DO NOT SPREAD TOO THIN. 6. Allow the first coat to dry 2 - 3 hours. High humidity and/or low
temperature conditions will extend th e dry time (recommended conditions of 65 - 80°F/40 - 60% relative
humidity). 7. For smoothest results, abrade with a Bona® Conditioning Pad before applying final coat.
Always vacuum and tack thoroughly with a slightly water dampened Bona Microfiber Mop or clot h after
abrading. Allow final coat to dry at least 24 hours before use.
CAUTION! Do not recap finish/hardener mixture after 4 hours to avoid pressure build - up. Dispose of any
remaining product in accordance with local, state and federal regulations. Decon taminate empty hardener
(Part B) bottle prior to disposal by adding water to the one - quart line. Recap. Shake vigorously. Dispose
of.
POT LIFE: THE FINISH/HARDENER MIXTURE MUST BE USED WITHIN 4 HOURS AFTER IT IS
MIXED. Product properties are diminished af ter 4 hours. The finish and hardener can be mixed only one
time.
This product has a maximum VOC (Volatile Organic Compound) content of 210 grams per
INTERCOAT ABRASION: It is not necessary to abrade between Bona waterborne sealer and finish coats
unless m ore than 48 hours has passed since the previous coat was applied. For smoothest results,
abrade between all coats as necessary. When using solvent - based sealers, ALWAYS abrade before
finish coats. Always vacuum and tack thoroughly with a slightly water - dam pened Bona Microfiber Mop or
cloth after abrading.
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep
®
system,
applying 1 - 2 coats of Bona Traffic Anti - Slip finish. Delamination can occur if the Bona Prep process is n ot
followed and the floor has not been tested for compatibility.
CURING: The curing process takes approximately 7 days, (75% cured after 1 day, 90% after 3 days). Do
not replace area rugs until the floor has fully cured. The floor may be walked on after 24 hours, but
remains susceptible to scuffing or marring until completely cured. Furniture may be placed onto floor after
72 hours (90% cured). Do not drag or slide. Use only a dry Bona Microfiber Mop or cloth for cleaning
duri ng the first week.
CLEAN - UP: Application tools should be cleaned with water and stored in an airtight container.
FLOOR CARE: Put walk -off mats at all entrance doorways to keep out excessive dirt and grit. Sweep or
vacuum daily and damp - wipe as needed with Bona
®
Hardwood Floor Cleaner. Use Bona
®
Self - Adhesive
Felt Pads under furniture legs and appliances.
STORAGE: Nonflammable - Bona Traffic Anti - Slip and Hardener should be stored in a climate - controlled
environment. KEEP FROM FREEZING. Do not store above 100° F.
Item #: WT153918001
Size: 1 Gallon
#/ Case : 2
Order Information
Maintenance