Specifications

11
Field Programming
Field Programming
IMPORTANT:
The Subzone Lockout Switch (DIP
Switch 3) must be set to Off (O) for Field Programming.
When power is first applied, the following default settings
are loaded:
• Paging Zone Groups 1, 2, and 3: Cleared and produce
no action when accessed
• Night Bell: Sounds in all Zones
• Shift Change/Emergency Call: Sounds in all Zones
• Shift Change /Emergency Call Tone: Set to produce two
dual-tone bursts
• Privacy Beep Feature: Disabled – no privacy beep
• All-Call Inhibit: All-Call Enabled
NOTE: If batteries are installed, it may be necessary to reset the
unit in order to institute default settings. See the section on
Resetting with Battery Backup on Page 12
.
Programming Zone Groups
The ZPM3 allows for three Paging Zone Groups (Zone
Groups 1, 2, and 3), each one consisting of up to three
user-selected zones. A night bell zone group (Zone Group
4) can be programmed to ring the night bell in up to three
zones. A Shift Change/Emergency Call Zone Group (Zone
Group 5) can be programmed to sound the Shift
Change/Emergency tone in up to three zones. Use the
following procedure to program zone groups.
1. Access the ZPM3 by dialing the trunk access number or
station access number. Listen for the confirmation tone
(if enabled).
2. Press and wait for the program tone (short beep).
3. Select the zone group to be programmed by pressing
the corresponding key for paging zone
groups 1, 2, or 3, respectively, to assign zones to a
night ringer zone group (instead of sounding in all zones),
or to assign zones to a Shift Change/Emergency
Call Zone Group (instead of sounding the shift change
tone or providing Emergency All-Call with alert tone to all
zones).
4. Press the keys corresponding to the desired zones (1-3)
to reside in the zone group up to three zones (if less than
3 zones are to be included, see note below).
5. Press and wait for a short beep, then hang up.
NOTE: To enter less than 3 zones, follow step 4 above but fill the
unused zone group position with the last zone selected (i.e., to
enter zones 1 & 2, dial 1-1-2). The ZPM3 records the last three
zone selections chosen no matter how many digits were pressed
during the programming procedure. This also makes it possible
to override any incorrect zone selections made during the pro-
gramming process.
Incorrect selection of zones for a zone group can be changed
during programming, however, the zone group number must be
correctly selected from the start. If the programming procedure
is started but you do not wish to complete it, hang up. If the #
key was not pressed a second time (Step 5), none of the selec-
tions will be committed to memory. If an illegal selection is made
during the programming procedure, a beeping error tone will be
heard in the handset – the ZPM3 must be put back on-hook and
the programming process restarted. If the ZPM3 sounds an error
tone immediately after pressing the # key for the first time, check
to see that the Subzone Lockout (DIP Switch 3 is in the OFF (O)
position.
Enable/Disable Privacy Beep
1. Access the ZPM3 by dialing the trunk access number or
station access number. Listen for the confirmation tone
(if enabled).
2. Press and wait for the program tone (short beep).
3. Enable the privacy beep by pressing .
4. Disable the privacy beep by pressing .
5. Press and wait for a short beep, then hang up.
Select Shift Change/Emergency All-Call Tone
1. Access the ZPM3 by dialing the trunk access number or
station access number. Listen for the confirmation tone
(if enabled).
2. Press and wait for the program tone (short beep).
3. Select the one-second tone burst by pressing
4. Select the two dual-tone bursts by pressing
5. Press and wait for a short beep, then hang up.
All-Call Inhibit
1. Access the ZPM3 by dialing the trunk access number or
station access number. Listen for the confirmation tone
(if enabled).
2. Press and wait for the program tone (short beep).
3. Inhibit All-Call paging by pressing .
4. Enable All-Call paging by pressing .
5. Press and wait for a short beep, then hang up.
5
, or
4
321
0
1 1
6
1
6
#
#
#
#
0
2 1
6
2
6
#
#
#
#
.
.
0
3 1
6
3
6