INSTRUCTION MANUAL
CONTENTS INTRODUCTION.....................................................................................2 USING THIS MANUAL.............................................................................2 SYSTEM FEATURES..................................................................................3 UDR16 RECEIVER....................................................................................4 UHT16 HANDHELD MICROPHONE TRANSMITTER.....................................
SYSTEM FEATURES UDR16 RECEIVER. • Frequency rotary DIP switch with 16 user-selectable channels in the wideopen UHF band for interference-free use anywhere • 120dB Dynamic Range • 150-250 ft. typical operating range — up to 500+ ft.
UDR16 RECEIVER 1. Rack Mounting the Receiver There are 2 options available (as accessories) for rack mounting the UDR16 receiver: single or side-by-side with another UDR16 receiver. a. Single mounting: Remove the receiver SIDE MOUNT CLIPS (1) from each side of the receiver (as shown) and slide in the optional wider RACK EARS (2). b.
. Channel Selection Turn the frequency rotary DIP SWITCH (11) to one of the sixteen channels. The slot on the switch shaft should match a number or letter on the dial, which indicates the selected channel. 6. Audio Level and Peak LED Indicator The UDR16 receiver is equipped with a five segment LED AUDIO LEVEL DISPLAY. (15). Occasional flickering of the top Peak LED indicator on loud inputs to the transmitter is normal.
UDR16 UHF Receiver 2 1 2 4 1 3 4 5 11 9 10 8 16 6 6 16 12 13 7 14 15
UHT16 HANDHELD MICROPHONE TRANSMITTER 1. Install batteries by unscrewing the BATTERY COMPARTMENT COVER (28). counterclockwise and remove, exposing the BATTERY HOLDER (26). Insert two fresh AA ALKALINE BATTERIES (27), observing the correct polarity, and screw the cover back on to the microphone. Make sure the cover is screwed clockwise completely.
UBP16 BODYPACK MICROPHONE TRANSMITTER 1. Open the BATTERY DOOR (30) by pulling on side tabs and swinging the lid open. Insert two fresh AAA ALKALINE BATTERIES into the BATTERY COMPARTMENT. (31), observing the correct polarity. Fresh alkaline batteries can last up to 5 hours in use, but in order to ensure optimum performance, it is recommended that the batteries be replaced after 3-4 hours of use. 2. The UBP16 is provided with a 3.5 mm LOCKING JACK (33) for connecting the audio input.
(Note: Observe care in selecting P.A. volume, transmitter location, and speaker placement so that acoustic feedback (howling and screeching) will be avoided. Please also note the pickup pattern characteristics of the microphone selected. Omni-directional mics pickup sound equally from all directions, and are prone to feedback if not used carefully. Uni-directional mics are more resistant to feedback, but best pick up sound sources that are directly in front of the mic.
UBP16 Body-Pack 40 37 33 39 34 35 36 CLIP 32 located on rear of Unit 38 31 30 10
SPECIFICATIONS OVERALL SYSTEM PERFORMANCE. RF Carrier Frequency.................UHF, 16-frequency group in separate bands within 470-510 MHz Frequency Stability....................+/- 0.005%, PLL synthesized Modulation...............................FM (F3E), +/- 50 kHz normal Frequency Response..................30 Hz - 21 kHz, -3dB Dynamic Range........................120 dB Total Harmonic Distortion...........< 0.5% Operating Range......................Up to 250 ft.
WARRANTY Bogen products are warranted to be free from defects in material or workmanship for one (1) year from the date of sale to the original purchaser. Any part of the product covered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen, at our option, provided the product is shipped insured and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446, USA. The product will be returned to you freight prepaid.
