Hardware List Part# Qty Description 31 4 NYLON BUSHING MEDEA {9211.083} 2 4 SHAFT COLLAR o {9211.046} 33 8 END CAP (8211-114) 34 4 FOOT CAP (8211-117) 35 4 RUBBER DONUTS B8 (8310-027) 36 2 STEEL CABLE 7540 ram 37 2 STEEL BUSHING W16 x 10.2 x 26.5L (8630018 38 2 WEIGHT STACK PIN LANYARD {FO20003) a8 2 HANDLE (B630-125) 41 4 OI LITE BUSHING . sometimes {8520-001}) 42 2 SHEET PREINSTALLED {B260-06Ry 43 2 FLAT POP PIN « PREINSTALLED {B250-068) 44 2 WEIGHT TACK STICKERS {8440.
Pars 11 Part# 12 Part# 13 Part# 14 Part# 15 Part# Selassie Alien Head Bolt Nylon Nut Nylon Nut (I 1J Nylon Nut Nut 700806 90 1T 120 130 140 Qly. 2 Qty. 2 Qiy. 20 Qly 4 Qiy. 2 Ciy.
Dorm Be careful to assemble il components B the vagueness they are presenter. Finger tighten ol headword o this stop unless RIGHT SIDE ASSEMBLY Crossover Cable (36} sybbrsranian potted. Ca bis End Bt Si op End Insert both Foot Caps (34} into Base Frame (AL Insert End Cap (46) into Base Frame (A). Insert four Round End Caps (45) info Base Frame (A}, Slide Guide Post (3} into Base Frame (A} and secure using.
Be careful to assemble il components B the vagueness they are presenter.
Be careful to assemble il components B the vagueness they are presenter.
Be careful to assemble il components B the vagueness they are presenter. Finger tighten ol headword o this stop unless RIGHT SIDE ASSEMBLY sybbrsranian potted. Crossover Cable (36} gl Stop Ene Founded the Cable End of Crossover Gable (36) from Pulley #1 up towards Pulley #2, Cable Bl _ 2480 Fandom Ring Crossover Cable (38) around Pulley #2, towards Pulley #3, then down forwards Fully #4, Route Crossover Cable (36) around Pulley #4, towards Pulley #5.
Dow me Be careful to assemble il components B the vagueness they are presenter. Finger tighten ol headword o this stop unless LEFT SIDE ASSEMBLY Crossover Cable (36} sybbrsranian potted. Ca bis End h MW Bt Si op End Sl Insert both Foot Caps (34) Into Base Rams (A).
Be careful to assemble il components B the vagueness they are presenter.
Be careful to assemble il components B the vagueness they are presenter.
Be careful to assemble il components B the vagueness they are presenter. Finger town s hardcovers o this step unless otherwise noted LEFT SIDE ASSEMBLY Crossover Cable (36} ) Bi op Ert Titicaca End &7 e That mm R A, Route the Cable End of Crossover Cable (38) from Pulley #1 up towards Pulley #2, B, Bring Crossover Cable (38) around Pulley #2, towards Pulley #3, then down towards Pulley 34, . Route Crossover Cable {36) around Pulley #4, forwards Pulley #5.
Be careful to assemble il components B the sensuousness they are presented, Finger malathion ol hardware fn thy sleep unless otherwise sled A Fave the Lat Side and Right Side of the GDCC200 wards each other as shown in the diagram.
e Accessory installation The GDCC200 comes equipped with 2 access odes: 1} Handle Strap 2} Naked Strap The diagrams en the following page show the proper installation of the above accessories. Use the provided Snap Links to properly connect the accessories to your Semisolid gym. The GDCC200 workout poster included with your machine is Installed on the side of Upright Frame (F) as shawl, Simply peel off the sticker cover on Porter Clips (48) and place the Sven spaced Poster Clips (48) onto Upright Frame (F).
