Installation Manual

ManualsBrandsBodine ManualsBallastsEmergency Ballast

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

! IMPORTANT SAFEGUARDS !

WHEN USING ELECTRICAL EQUIPMENT, BASIC

SAFETY PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED, INCLUDING THE FOLLOWING:

THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY.

THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.

EMERGENCY LIGHTING EQUIPMENT

Installation Instructions

SAVE THESE INSTRUCTIONS

Ni - Cd

1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter

connector must be open. Do not join inverter connector until installation is complete and AC power is

supplied to the emergency ballast.

2. This product is for use with most 17 W through 40 W T8, T10 or T12 single pin or bipin ﬂuorescent lamps,

including energy saving, circline, U-shaped and rapid-start (4-pin) long compact ﬂuorescent lamps.

3. Make sure all connections are in accordance with the National Electrical Code and any local regulations.

4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and

inverter connector of the emergency ballast before servicing.

5. This emergency ballast is for factory or ﬁeld installation in either the ballast channel or on top of the

ﬁxture.

6. This product is for use in indoor ﬁxtures except air handling heated air outlets, and wet, damp, or

hazardous locations.

7. An unswitched AC power source is required (120 or 277 VAC, 60 Hz).

8. Do not install near gas or electric heaters.

9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not ﬁeld

replaceable. Contact the manufacturer for information on service.

10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe

condition.

11. Do not use this product for other than intended use.

12. Servicing should be performed by qualiﬁed service personnel.

B100

A Division of Philips Electronics North America Corporation

236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-854-1630 • www.philips.com/bodine

71000025

03/21/11

Summary of content (4 pages)

PAGE 1
B100 Installation Instructions EMERGENCY LIGHTING EQUIPMENT ! IMPORTANT SAFEGUARDS ! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter connector must be open. Do not join inverter connector until installation is complete and AC power is supplied to the emergency ballast. 2.
PAGE 2
INSTALLATION WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON RED & YELLOW OUTPUT LEADS PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN. DO NOT JOIN INVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED TO THE EMERGENCY BALLAST. NOTE: STEP #1 Make sure the necessary branch circuit wiring is available. An unswitched source of power is required. The emergency ballast must be fed from the same branch circuit as the AC ballast.
PAGE 3
INSTALLATION TROFFER STYLE FIXTURE STRIP STYLE FIXTURE Fixture Fixture Charging Indicator Light Charging Indicator Light Violet (+) Violet (+) Brown (–) Brown (–) 5/8" Black Bushing 1/2" White Bushing 1/2" White Bushing 5/8" Black Bushing 1/2" Punch NOTE: After installing the charging indicator light and test switch, mark each with the appropriate label. STEP #4 WIRING THE EMERGENCY BALLAST > Determine the type of AC ballast installed in the fixture.
PAGE 4
EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.