User's Manual

BZ0-MINI2SMSB02
版本测试员
技术要求：
1.成品尺寸65*65mm
2.128g铜版纸
3.风琴折
4.黑色单色印刷
品质经理 业务经理
研发经理
USERS MANUAL
MINI2 BT Version
Multimedia speaker
SPECIFICATIONS:
1. Power Output: RMS 3W X 2 (THD=10%)
2. Connection options: BT &3.5mm AUX-in
3. Power Input: USB direct plug (no built-in battery)
4. Power supply: (5V，1A)
5. Speaker specifications: 2 inches X2
6. Adjustment form: wire-controlled volume adjustment
7. Frequency response: 45Hz~16KHz
8. Signal to noise ratio: ≥88dB
9. Impedance: 4 Ω
10. Distortion: ≤0.5%
1. Adjust the volume
Use the dial switch to adjust the volume of the sound.
Pull to" Vol - "or "Vol+ "to adjust the volume,
the volume is at the maximum when you hear "dudu".
2. Next song or previous song
Press "Vol - " direction about 1.5 seconds to the previous
song.
Press "Vol +" direction about 1.5 seconds to the next song.
3. Switch the mode between BT and wired
Long Press the dial switch for about 1.5 seconds to
switch the mode;
When you hear the" dududu", which is in BT mode, search
“MINI2”on your BT list from your device.
When you hear "du", it's in wired mode, you could directly
play the playlist of your device.
Note: The appearance of the speaker is for reference only,
please refer to the actual product!
PC Computer
Socket Location
Control Knob
3.5mm
Aux-in
Computer
USB Port
Vol+ Vol-
4. Switch RGB light mode (6 colors )
Short press the dial switch in any mode. You can switch
from RGB fast flash — RGB slow flash — Red — Green
—Blue— Purple — White — Yellow — Lights off.
5. Disconnect BT and use the new device connect
Double press the dial switch and you will hear
"Disconnected".
When you want to use the new device to connect
"MINI 2" speaker via BT, only search for your BT list
and connect, you will hear "Connected".
Function Description About Control Knob
Company: MOSWS INTERNATIONAL LIMITED
Add: FLAT/RM 07, BLK B, 5/F KING YIP FACTORY BUILDING, 59 KING
YIP STREET, KWUN TONG, KOWLOON HONGKONG 999077
Production Standard: IEC/EN60065
MADE IN CHINA
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator & your
body. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
FCC Requirement
Your PC will automatically detect the MINI 2 when you
plug in the USB cable and 3.5mm AUX-in cable. RGB light
will be working.
If you do not hear any audio playing from the speaker,
please check the output device list from the "Sound"
setting and set the "MINI 2" as the output speaker.
Or you can connect by BT, choose "MINI 2" from your
BT list.
Connecting to MP3/Mobile Phones/
other Audio Devices
1. The USB interface of your computer can work normally or not?
2. The audio driver of your computer sound is up to date or not?
3. Click the "Speaker" icon in the taskbar, and make sure
that" Headset(Realtek(R)Audio)" is selected as your
computer playback device.
About Sound
If there is no sound response after plugging it into the
computer USB port, please make sure:
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
About BT Connection
1. Make sure the BT of the speaker is not connected by other
devices.
2. Unplug the USB from your device.
3. Delete" MINI2" memorized on your device, then search for
"MINI2" and connect again.
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
If you require more assistance, please do not heistate to contact us
directly via
[e-mail]. Alternatively, you can
also contact us in your order list or get support online easily on Amazon.
You can also connect the speaker to your device via
3.5mm AUX-in cable or BT mode.
*Note that the speaker has to be powered via USB while
connected via AUX-in.
Connecting to PC and MAC
Troubleshooting
MORE QUESTIONS ?
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: