Specification Sheet
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 12/8/17 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2017 by Gamco Commercial Restroom Accessories
OPERATION:
Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-density
polyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performance
requirements when properly installed.
Warning: To ensure that the unit supports the intended loads, baby changing stations must be properly installed according to the
manufacturer’s instructions.
INSTALLATION:
To ensure proper installation and compliance to building codes, it is recommended that a qualified person or carpenter perform
the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supporting significant
weight and can accommodate the supplied installation hardware. The Gamco Baby Changing Station meets ADA regulations
when properly installed.
Drilling holes and mounting the station:
1. Remove the station from the shipping container and check for any freight damage. Identify the best location for
installing the unit. Hold the unit in place, open the bed, and make sure that there is adequate operating clearance.
2. Based upon the type of wall on which the unit will be mounted, determine the best method of mounting. Not all of
included hardware may be required for proper installation.
3. The horizontal unit has four mounting holes provided in the back wall of the unit, which are positioned on a 32"
(813mm) stud center. If possible, locate the wood or metal wall studs for fastening the changing station in the desired
location. If the walls do not have studs on the center as outlined, make sure at least one side of the unit is installed
into the stud. Use toggles (may have to purchase) for holes on the other side.
4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 44" (1118mm)
up from the floor, at the center of the stud, and mark the wall. Line up the top left mounting hole with this mark, then
use a measuring tape and level to mark the remaining three mounting holes. This will locate the bottom of the station
26-1/2" (673mm) from the floor and the top of the bed at 33" (838mm).
Using Wood Screws:
If the wall is masonry or tile over wood studs, use a 7/32" masonry drill bit for the pilot hole until you hit the stud. Change bit
to 1/8" regular drill bit. Use the four 1/4" x 3" panhead wood screws with supplied washers.
Using Toggle Fasteners:
If the wall has wood studs on that are not on 32" (813mm) centers, has metal studs or an underlying surface of concrete block,
drill with a 1/2" (12mm) masonry bit (you may have to purchase toggles before installing). You must allow a minimum of inside
wall space for toggles to turn depending on toggles used. Insert and tighten toggles.
5. Replacement parts and additional liners can be purchased from your local distributor or by calling.
Bobrick Customer Service Phone: (818) 982-9600 • Fax: 818-503-1102 or email customerservice@bobrick.com
SPECIFICATION:
Baby changing station body shall be durable, high-density polyethylene. Design of unit shall be surface-mounted. Unit shall
be equipped with a pneumatic cylinder for controlled opening and closing of bed. No hinge structure shall be exposed on
interior or exterior surfaces. Bed shall be secured to back plate with a concealed, full-length steel-on-steel hinge. Unit shall have
11-gauge steel mounting plates with mounting hardware included. Unit shall have Microban® antimicrobial embedded into
plastic material. Unit shall conform to ANSI A117.1 Accessible and Usable Buildings and Facilities, ASTM F2285-04 (formerly
ASTM PS125) Standard Safety Performance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4
Product Safety Signs and Labels, ASTM G21 Antifungal and ASTM G22 Antibacterial Standards or local code if more stringent
installation requirements are applicable for Accessibility. Unit shall comply with ADA regulations when properly installed. Bed
shall have smooth concave changing area with a nylon safety strap and two hooks for bags or purses. Unit shall have a built-in
Liner Dispenser for use with 3-ply chemical free biodegradable bed liners, universal instruction graphics and safety messages
in 6 languages and braille. Unit shall be backed by manufacturer’s 5-year limited warranty on materials and workmanship. Unit
shall be manufactured in the U.S.A.
Baby Changing Station shall be model BCS-1 or -2 of Gamco Commercial Restroom Accessories, One Gamco
Place, Durant, OK, 74701-1910