Spec Sheet

ManualsBrandsBobrick ManualsBathroom AccessoriesB-710 CompacDryer Surface-Mounted Hand Dryer with Electronic Control, Fan, Automatic Thermal-Overload Switch and Heating Element in Grey Plastic High Gloss Finish

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 4/27/11

R/A

Printed in U.S.A.

Technical Data

BOBRICK

AUTOMATIC HAND DRYER

1-7/16"

35mm

1-1/16"

25mm

10-15/16"

280mm

8-13/16"

225mm

1-7/16"

35mm

7-7/8"

200mm

10-13/16"

275mm

See Table

for

Recommended

Mounting

Height Off Floor

Cover

Mounting Base

Finish Face of Wall

3/4"

19mm

Diameter Hole

for Between-Wall

Wiring

5/8" x 9/16"

16 x 14mm

Opening for Surface Wiring

Wire Opening

10-15/16"

280mm

125mm

5-3/16"

130mm

8-1/16"

205mm

Typ.

4-1/2"

115mm

SURFACE-MOUNTED

AUTOMATIC

HAND DRYER

Model B-710 115-Volt CompacDryer™

115V AC, 15 Amp, 1725 Watts, 60 Hz, Single Phase, cULus Listed

MATERIALS:

Cover — One-piece, 3/32'' (2.6mm) thick ﬁ re-retardant, molded , high-quality, high-impact, pale grey (Bobrick color #889) ABS plastic,

5-V rated. Cover is secured to mounting base with three ﬂ at-head stainless steel screws.

Mounting Base and Fan Housing — 5-64" (2.0mm) thick ﬁ re-retardant molded grey plastic with high-gloss ﬁ nish. Air-inlet grille ﬁ ts

into bottom of mounting base. Air-outlet grille is secured between fan housing and mounting base.

Motor — 115V AC, 90 W, 60 Hz, 2500 rpm. Brushless, external rotor motor. Sealed ball bearings at both ends of drive shaft;

maintenance free. Equipped with an automatic thermal-overload switch.

Fan — Dynamically balanced 5-15/64" (133mm) diameter centrifugal fan with multiple metallic vanes. Directs air ﬂ ow from heating

element at 90 cfm, mixes air to provide uniform temperature.

Heating Element — Coiled nickel-chrome heating element is protected by an automatic thermal-overload switch. Heating element,

which is located on inlet side of fan, heats air without hot spots — inaccessible to vandals.

Electronic Control — Infrared sensor automatically turns dryer on when hands are held under air-outlet opening and across path of

sensor. Remove hands from path of sensor and dryer stops. Electronic sensor has automatic shutoff approximately two minutes after

dryer turns on if an inanimate object, such as tape or chewing gum, is placed across sensor lens. After inanimate object is removed,

electronic sensor automatically resets itself and dryer operates normally.

continued . . .

B-710

Designer's Note: Model B-710 CompacDryer™ is not designed for vandal-prone installations. For vandal-prone installations, use Bobrick

AirCraft® Dryers with cast-iron, vitreous enamel ﬁ nished covers.

Children's Washrooms, ages 3-4 36'' (915mm)

Children's Washrooms, ages 5-8 40'' (1015mm)

Children's Washrooms, ages 9-12 44'' (1120mm)

Universal Design 48'' (1219mm)

RECOMMENDED MOUNTING HEIGHTS

Bottom screw hole of mounting base to ﬁ nish face of ﬂ oor

Summary of content (2 pages)

PAGE 1
SURFACE-MOUNTED AUTOMATIC HAND DRYER Technical Data B-710 Model B-710 115-Volt CompacDr yer™ 115V AC, 15 Amp, 1725 Watts, 60 Hz, Single Phase, cULus Listed Designer's Note: Model B-710 CompacDryer™ is not designed for vandal-prone installations. For vandal-prone installations, use Bobrick AirCraft® Dryers with cast-iron, vitreous enamel finished covers.
PAGE 2
OPERATION: No-touch operation. Electronic sensor automatically turns dryer on when hands are held under air-outlet opening and across path of sensor. Remove hands from path of sensor and dryer stops. Dryer will not stop by itself before user is satisfied hands are dry. Dryer operates only when actually drying hands, which saves energy and operating costs. Electronic sensor will automatically shut dryer off two minutes after dryer turns on if an inanimate object is placed across sensor lens.