Specification Sheet

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-35715 r9/27/16
R/A, S/C
Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2016 by Bobrick Washroom Equipment, Inc.
INSTALLATION:
Mount unit in toilet partition 1/2'' to 3-7/8'' (13 x 98mm) thick, centered through a cutout specially ordered from partition
manufacturer or field cut. Dimensions of cutout are to be 15-1/2" wide x 28-7/8" high (395 x 735mm). Top of cutout should be
41" (1041mm) from finish face of floor to allow placement of horizontal grab bar at 33" (840mm) height across front of unit and
installation of 18" vertical grab bar for (ICC A117.1-2009). For factory-made cutouts, location and size details must be furnished
to partition manufacturer. For hollow-core metal partitions, provide solid framing into which sheet-metal mounting screws can
be secured.
For installation with sheet-metal screws furnished, place unit firmly in partition cutout, making certain entire perimeter of
fixed flange is flush with and tight against partition surface. Install the unit so the side that has the fixed flange flush with face
of cabinet is in the accessible toilet compartment for use by individuals with disabilities. Secure to partition with sheet-metal
screws through four mounting holes in fixed flange at points indicated by an S. On other side of partition, position adjustable
flange (which serves as an escutcheon) so mounting holes are not in line with mounting holes in fixed flange. Make certain
entire perimeter of adjustable flange is flush with and tight against partition surface before securing with sheet-metal screws
furnished.
For through-bolting method of installation, make sure mounting holes in adjustable flange are in line with holes in fixed flange.
Using adjustable flange as template to mark locations, drill 7/32" or 1/4" (5.5 or 6.4mm) holes through partition. Provide
four binder posts and #6 (3.5mm) flat-head screws to secure unit and its adjustable flange. Obtain binder posts and screws by
ordering Bobrick Binder Post Kit No. 354-119 for partitions 1/2" (13mm) thick only or Kit No. 354-124 for partitions 3/4" to
1-1/4" (19 to 32mm) thick.
Note: Cutouts in Bobrick toilet partitions can be pre-cut for Bobrick partition-mounted accessories at factory if location and size
of cutouts are specified and order for both partitions and accessories are received together.
Designer's Notes:
1. Partition-mounted B-35715 with one side flush to partition in accessible toilet compartment has toilet tissue dispenser on
right side of unit.
2. Position unit on panel with centerline of toilet tissue dispenser 7" - 9" (180 - 230mm) in front of leading edge of toilet.
3. For unit to mount on right side of toilet (when seated on toilet) see model B-3571.
4. When combination units are mounted in an accessible toilet compartment through the shared toilet partition panel, the
units location in the adjoining toilet compartment must permit the units complete operation, and allow for the unit's door to
swing clear of the toilet when custodians service the unit.
5. For visual placement of models inside toilet compartment, refer to Technical Bulletin TB-92.
SPECIFICATION:
Partition-mounted seat-cover dispenser, sanitary napkin disposal, and toilet tissue dispenser shall be Type-304 stainless steel
with all-welded construction; exposed surfaces shall have satin finish. Toilet tissue dispenser shall be ABS plastic. Flanges shall
be drawn and beveled, one-piece, seamless construction. Unit shall mount in partition and serve two toilet compartments. One
side of unit shall mount flush against partition in accessible toilet compartment to allow clearance for grab bar across front
of unit and installation of 18" vertical grab bar (ICC A117.1-2009). Door shall be one-piece, seamless construction; secured to
cabinet with a full-length stainless steel piano-hinge; and equipped with two tumbler locks keyed like other Bobrick washroom
accessories. Self-closing disposal panels shall be secured to cabinet with spring-loaded, full-length stainless steel piano-hinges
have hemmed edges and equipped with international graphic symbols identifying napkin disposal. Napkin disposal shall be
furnished with a removable, leak-proof, molded polyethylene receptacle with a capacity of 0.8-gal. (3.0-L). Toilet seat-cover
dispenser and sanitary napkin disposal shall be serviced from one side only. Toilet seat-cover dispenser shall be equipped
with a plastic sight-barrier panel and hold 1000 paper covers. Unit shall be equipped with four theft-resistant, heavy-duty ABS
toilet tissue spindles that hold standard-core rolls up to 5-1/4" (135mm) diameter (1800 sheets). Spindles shall be removable
from cabinet when door is open; when door is closed, removal shall require a special key provided for the concealed locking
mechanism in spindles.
Partition-Mounted Seat-Cover Dispenser, Sanitary Napkin Disposal, And Toilet Tissue Dispenser shall be Model
B-35715 of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jack son, Tennessee; Los Angeles,
California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty.
Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.