Specification Sheet

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-357 Rev. 6/30/15

R/A, S/C

Printed in U.S.A.

INSTALLATION:

Mount unit in toilet partition 1/2'' to 2'' (13 x 51mm) thick, centered through a cutout specially ordered from partition

manufacturer or ﬁeld cut. Dimensions of cutout are to be 15-1/2" wide x 28-7/8" high (395 x 735mm). For factory-made

cutouts, location and size details must be furnished to partition manufacturer. For hollow-core metal partitions, provide solid

framing into which mounting screws can be secured.

For installation with sheet-metal screws furnished, place unit ﬁrmly in partition cutout, making certain entire perimeter of

ﬁxed ﬂange is ﬂush with and tight against partition surface. Secure to partition with sheet-metal screws through four mounting

holes at points indicated by an S. On other side of partition, position adjustable ﬂange (which serves as an escutcheon) so

mounting holes are not inline with mounting holes in ﬁxed ﬂange. Make certain entire perimeter of adjustable ﬂange is ﬂush

with and tight against partition surface before securing with sheet-metal screws furnished.

For through-bolting method of installation, make sure mounting holes in adjustable ﬂange are inline with holes in ﬁxed ﬂange.

Using adjustable ﬂange as template to mark locations, drill 7/32" or 1/4" (5.5 or 6.4mm) holes through partition. Provide four

binder posts and #6 (3.5mm) ﬂat-head screws to secure unit and its adjustable ﬂange. Obtain binder posts and screws by

ordering Bobrick Binder Post Kit No. 354-119 for partitions 1/2" (13mm) thick only or Kit No. 354-124 for partitions 3/4" to

1-1/4" (19 to 32mm) thick.

Note: Cutouts in Bobrick toilet partitions can be pre-cut for Bobrick partition-mounted accessories at factory if location and

size of cutouts are speciﬁed and order for both partitions and accessories are received together.

Important Note: Where ANSI 2003 and 2009 apply individual toilet tissue dispensers, toilet-seat-cover dispensers and sanitary

napkin disposals must be installed below the horizontal grab bar allowing space for installation of the vertical grab bar.

SPECIfICATION:

Partition-mounted toilet-seat-cover dispenser, sanitary napkin disposal, and toilet tissue dispenser shall be type-304 stainless

steel with all-welded construction; exposed surfaces shall have satin ﬁnish. Toilet tissue dispenser shall be ABS plastic.

Flanges shall be drawn and beveled, one-piece, seamless construction. Unit shall mount in partition and serve two toilet

compartments. Door shall be one-piece, seamless construction; secured to cabinet with a full-length stainless steel piano-

hinge; and equipped with two tumbler locks keyed like other Bobrick washroom accessories. Self-closing disposal panels

shall be secured to cabinet with spring-loaded, full-length stainless steel piano-hinges, have hemmed edges and equipped with

international graphic symbols identifying napkin disposal. Napkin disposal shall be furnished with a removable, leak-proof,

molded polyethylene receptacle with a capacity of 0.8-gal. (3.0-L). Toilet-seat-cover dispenser and sanitary napkin disposal shall

be serviced from one side only. Toilet-seat-cover dispenser shall be equipped with a plastic sight-barrier panel and hold 1000

paper covers. Unit shall be equipped with four theft-resistant, heavy-duty ABS toilet tissue spindles that hold standard-core

rolls up to 5-1/4'' (135mm) diameter (1800 sheets). Spindles shall be removable from cabinet only when door is open.

Partition-Mounted Seat-Cover Dispenser, Sanitary Napkin Disposal, And Toilet Tissue Dispenser Model

B-357 of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jack son, Tennessee; Los Angeles,

California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty.

Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.