Specification Sheet

ManualsBrandsBobrick ManualsCombo UnitsBobrick ClassicSeries Recessed Seat Cover and Toilet Tissue Dispenser

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 6/30/14

R/A, S/C

Printed in U.S.A.

continued . . .

Technical Data

Rough Wall Opening

16" (405mm) wide

29-1/4" (745mm) high

4" (102mm) minimum recessed depth

See Designer's Notes for Rough Wall Opening Location Information

MATERIALS:

Cabinet — 18-8, type-304, heavy-gauge stainless steel. All-welded construction. Exposed surfaces have satin ﬁnish.

Flange — 18-8, type-304, 22-gauge (0.8mm) stainless steel with satin ﬁnish. Drawn and beveled, one-piece, seamless construc-

tion.

Doors (2) — 18-8, type-304, 18-gauge (1.2mm) stainless steel with satin ﬁnish. One-piece, seamless construction. Secured to

cabinet with a full-length stainless steel piano-hinge. Equipped with a tumbler lock keyed like other Bobrick washroom

accessories.

Toilet Tissue Dispensers (2) — .100" (2.5mm) thick ABS. Equipped with two theft-resistant, heavy-duty, one-piece, molded

ABS spindles.

OPERATION:

Doors unlock with key provided and swing open for ﬁlling. Toilet seat-cover dispenser holds 500 single- or half-fold paper

covers. Spindles may be removed from cabinet when door is open. Unit holds two standard-core toilet tissue rolls up to 5-1/4"

(135mm) diameter (1800 sheets).

Designer's Note: It is recommended that one full toilet tissue roll remain wrapped until the other roll has been depleted to avoid

wasting ends of both rolls.

ClassicSeries

RECESSED

TOILET SEAT-COVER AND

TOILET TISSUE DISPENSER

B-3474

17-3/16''

435mm

22-3/4''

580mm

5-5/8''

140

30-5/8''

780mm

27-13/16''

705mm

15-3/16''

385mm

3-3/4''

95mm

11-7/16''

290mm

1''

25mm

Ty p.

Toilet-Seat-Cover

Dispenser

Toilet Tissue

Dispenser (2)

3-15/16''

100mm

Upper Door

28-3/4''

730mm

Recommended Mounting Height Off Floor

For Accessible Design

42-3/8''

1075mm

3''

75mm

Shelf

Grab Bar

(Not Furnished)

33''

840mm

Floor

Lock & Key (2)

Finish Face of Wall

Lower Door

3/16''

5mm

Recommended Mounting Height Off Floor

58''

1500mm

Centerline of Toilet Tissue

Dispenser shall be

7'' to 9'' (180 to 230mm)

in Front of Toilet

Outlet of Toilet Tissue Roll

shall be 18'' (460mm) ICC/ANSI

or 15'' (380mm) ADA Above Floor

24-5/8''

625mm

to Back Wall

Summary of content (2 pages)

PAGE 1
ClassicSeries® Technical Data B-3474 RECESSED TOILET SEAT-COVER AND TOILET TISSUE DISPENSER Finish Face of Wall 17-3/16'' 3'' 435mm 75mm S Toilet-Seat-Cover Dispenser S 28-3/4'' 730mm 27-13/16'' 705mm 22-3/4'' 33'' 580mm 840mm Lock & Key (2) to Floor Toilet Tissue Dispenser (2) S 5-5/8'' 140mm S 42-3/8'' 1075mm Shelf 58'' 1500mm Grab Bar (Not Furnished) Recommended Mounting Height Off Floor For Accessible Design Upper Door 780mm Recommended Mounting Height Off Floor S 30-5/8''
PAGE 2
INSTALLATION: Provide framed rough wall opening 16" wide x 29-1/4" high (405 x 745mm). Minimum recessed depth required from finish face of wall is 4" (102mm). Top of wall opening should be 42-3/8" (1075mm) and installation of 18" vertical grab bar (ICC A117.1-2009) from finish face of floor to allow placement of horizontal grab bar at 33" (840mm) height across front of unit. Allow clearance for construction features that may protrude into rough wall opening from opposite wall.