Installation Sheet

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 4/24/20
R/A, S/C
Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2020 by Bobrick Washroom Equipment, Inc.
continued . . .
Technical Data
MATERIALS:
Cabinet — 18-8, Type-304, heavy-gauge stainless steel. All-welded construction. Exposed surfaces have satin finish.
Flange — 18-8, Type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn and beveled, one-piece, seamless
construction.
Doors (2) — 18-8, Type-304, 18-gauge (1.2mm) stainless steel with satin finish. One-piece, seamless construction. Secured to
cabinet with a full-length stainless steel piano-hinge. Equipped with a tumbler lock keyed like other Bobrick washroom
accessories.
Toilet Tissue Dispensers (2) — .100" (2.5mm) thick ABS. Equipped with two theft-resistant, heavy-duty, one-piece, molded
ABS spindles.
OPERATION:
Doors unlock with key provided and swing open for filling. Toilet seat-cover dispenser holds 500 single- or half-fold paper
covers. Spindles may be removed from cabinet when door is open. Unit holds two standard-core toilet tissue rolls up to 5-1/4"
(135mm) diameter (1800 sheets).
Designer's Note: It is recommended that one full toilet tissue roll remain wrapped until the other roll has been depleted to avoid
wasting ends of both rolls.
ClassicSeries
®
RECESSED
TOILET SEAT-COVER AND
TOILET TISSUE DISPENSER
B-3474
3''
76
mm
3''
76
mm
2-13/16''
71
mm
17-3/16''
435mm
22-3/4''
580mm
30-5/8''
780mm
27-13/16''
705mm
S
S
15-3/16''
385mm
3-3/4''
95mm
11-7/16''
290mm
1''
25mm
Ty p .
S
S
Toilet-Seat-Cover
Dispenser
Toilet Tissue
Dispenser (2)
3-15/16''
100mm
S
Upper Door
28-3/4''
730mm
3''
75mm
Shelf
Grab Bar
(Not Furnished)
Lock & Key (2)
Finish Face of Wall
Lower
Door
3/16''
5mm
Centerline of Toilet Tissue
Dispenser shall be
7'' to 9'' (180 to 230mm)
in Front of Toilet
C
L
Bottom Outlet of Toilet Tissue Roll shall be
19'' min. (485mm) for CBC
18'' min. (460mm) for ICC/ANSI
15'' (380mm) for ADA
Above Floor
See
Chart
S
S
Recommended Mounting Height Off Floor for CBC
45-7/8" (1166mm)
Recommended Mounting Height off Floor for ICC A117.1
Recommended Mounting Height Off Floor for ADA
Grab Bar Top Above Floor
35" (889mm) 35" (889mm) 33" (838mm)
Toilet Tissue Dispenser
Bottom of Outlet Above Floor
19" (482mm) 18" (457mm) 15" (381mm)
CBC
ICC A117.1
ADA
44-7/8" (1140mm) 41-7/8" (1064mm)
Note: For accessible toilet compartments, please use horizontal
recessed or surface -mounted combination dispenser-/disposal-
units, B-3091 or B-3092 Series, to comply with ADA 1-1/2"
absolute Grab Bar wall spacing.
Rough Wall Opening
16" (405mm) wide
29-1/4" (745mm) high
4" (102mm) minimum recessed depth
See Designer's Notes under Installation for
Rough Wall Opening Location Information