Specification Sheet

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 3/11/16

PoWeR ReQuiRementS:

Dispenser is powered by 4, “D” size alkaline batteries (not furnished) or a 6-volt DC power supply. Power supply is an optional accessory: order

Bobrick Part No. 3974-57. (For non-U.S. compatible plugs, order Part No. 3974-58).

inStAllAtion:

Provide framed rough wall opening 16” wide x 18 7/8” high (405 x 480mm). Minimum recessed depth required to ﬁnish face of wall is 4"

(102mm). Allow clearance for construction features that may protrude into rough wall opening from opposite wall. Coordinate with mechanical

engineer to avoid pipes, vents and conduits. If unit projects above top of wainscot, provide channel or other ﬁller to eliminate gap between

ﬂange and ﬁnish face of wall. Mount the Shell in wall opening with shims between framing and the shell at four points indicated by an S, then

secure the Shell with four #8 x 1-1/4" (4.2 x 32mm) ﬂat-head sheet-metal screws provided. Care should be taken to ensure that the heads of the

mounting screws do not protrude. For plaster or dry wall construction, provide concealed backing to comply with local building codes, then

secure the Shell with sheet-metal screws. For other wall surfaces, provide ﬁber plugs or expansion shields for use with ﬂat-head sheet-metal

screws, or provide 1/8" (3mm) toggle bolts or expansion bolts. Unlock and open the door of the dispenser cabinet. Carefully slide the dispenser

cabinet into the shell while supporting it from underneath with one hand. Attach dispenser cabinet to shell using the pre-drilled pilot holes in

the shell and four #8 x 1/2" (4.2 x 13mm) sheet metal screws (provided).

Open battery cover at the front of the dispenser and install 4, “D” size alkaline batteries. Select sheet length and “Paper Saver” mode using the

switches to the right of the batteries. Load paper towel using the instructions on the dispenser.

Electrical supply for use with 6-volt DC power supply must be installed per applicable building codes.

SPeciFicAtion:

Semi-recessed mounted automatic universal roll paper towel dispenser shall be type-304 stainless steel with all-welded construction; exposed

surfaces shall have satin ﬁnish. Door shall be secured to cabinet with a full-length stainless steel piano-hinge and equipped with a concealed

tumbler lock keyed like other Bobrick washroom accessories. No-touch dispenser, equipped with an intuitive LED light to direct patrons to the

dispense area, dispenses universal, 1-1/2" to 2" (38 to 51mm) diameter cores, up to 8" (205mm) diameter, 8" (205mm) wide, non-perforated,

non-proprietary rolls. 800 ft (244 m) long. Dispenser automatically dispenses towel when hands are placed under the towel opening. Dispenser

can be powered by 4 “D” size alkaline batteries or an optional 6-volt DC power supply. LED light at the towel opening ﬂashes green when

dispenser is ready to dispense, ﬂashes orange, indicating low battery, ﬂashes red if not ready to dispense or in need of service. Equipped

with switches that allow paper length to be set at 9" (230mm), 12" (305mm) or 15" (380mm) and “Paper Saver” feature that provides a shorter

second sheet with options of 25% shorter and 12.5% shorter. Automatic transfer shall dispense stub roll up to 3-1/2" (90mm) diameter before

new roll is dispensed.

Semi-Recessed Automatic Universal Roll Paper Towel Dispenser shall be Model B-29744 of Bobrick Washroom Equipment,

Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company,

Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United

Kingdom.