Specification Sheet
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 7/6/17
R/A, S/C
Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2017 by Bobrick Washroom Equipment, Inc.
Technical Data
17-3/16''
435mm
Lock
30-7/8''
785mm
S
S
15-3/16''
385mm
12-5/16''
285mm
Lock & Key (2)
1-1/8''
30mm
Ty p.
4-7/8''
125mm
S
S
Toilet-Seat-Cover
Dispenser
Toilet Tissue
Dispenser (2)
S
Skirt
S
Recommended Mounting Height Off Floor
For Universal / Accessible Design
60''
1525mm
4-3/16''
105mm
Door
Finish Face of Wall
Centerline of Toilet Tissue
Dispenser shall be
7'' to 9'' (180 to 230mm)
in Front of Toilet
C
L
MATERIALS:
Skirt — 18-8, Type-304, heavy-gauge stainless steel. Exposed surfaces have satin fi nish.
Flange — 18-8, Type-304, 22-gauge (0.8mm) stainless steel with satin fi nish. Drawn and beveled, one-piece, seamless
construc tion.
Doors — 18-8, Type-304, 18-gauge (1.2mm) stainless steel with satin fi nish. One-piece, seamless construction. Secured to unit
with a full-length stainless steel piano-hinge. Equipped with two tumbler locks keyed like other Bobrick washroom accessories.
Toilet Tissue Dispensers (2) — .100" (2.5mm) thick ABS. Equipped with two theft-resistant, heavy-duty, one-piece, molded
ABS spindles.
OPERATION:
Toilet-seat-cover dispenser holds 500 single- or half-fold paper covers. Doors unlock with key provided and swing open for
fi lling. Spindles may be removed from unit only when door is open. Unit holds two standard-core toilet tissue rolls up to 5-1/4''
(135mm) diameter (1800 sheets).
INSTALLATION:
Mount unit on wall with four #8 x 1-1/4'' (4.2 x 32mm) sheet-metal screws (not furnished) at points indicated by an S. For
plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure unit with screws.
For other wall surfaces, provide fi ber plugs or expansion shields for use with screws, or provide 1/8" (3mm) toggle bolts or
expansion bolts.
Important Note: Where ANSI 2003 and 2009 apply individual toilet tissue dispensers, toilet-seat-cover dispensers and sanitary
napkin disposals must be installed below the horizontal grab bar allowing space for installation of the vertical grab bar.
SPECIFICATION:
Surface-mounted toilet-seat-cover and toilet tissue dispenser shall be Type-304 stainless steel; exposed surfaces shall have satin
fi nish. Toilet tissue dispenser shall be ABS plastic. Flange shall be drawn and beveled, one-piece, seamless construction. Unit
shall be mounted on side wall of single toilet compartment. Doors shall be one-piece, seamless construction; secured to unit
with a full-length stainless steel piano-hinge; and equipped with tumbler locks keyed like other Bobrick washroom accessories.
Toilet-seat-cover dispenser shall hold 500 paper covers. Unit shall be equipped with two theft-resistant, heavy-duty ABS toilet
tissue spindles that hold standard-core rolls up to 5-1/4'' (135mm) diameter (1800 sheets). Spindles shall be removable from
unit only when door is open.
Surface-Mounted Seat-Cover And Toilet Tissue Dispenser shall be Model B-3479 of Bobrick Washroom
Equipment, Inc., Clifton Park, New York; Jack son, Tennessee; Los Angeles, California; Bobrick Washroom
Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick
Washroom Equipment Limited, United Kingdom.
ClassicSeries
®
SURFACE-MOUNTED
SEAT-COVER AND
TOILET TISSUE DISPENSER
B-3479