Specification Sheet

ManualsBrandsBob Smith Industries ManualsAutomotiveBob Smith Industries BSI-203 Mid-Cure Epoxy (4.5 oz. Combined)

Company address: Contact information:

Bob Smith Industries, Inc.

8060 Morro Road

Atascadero, CA 93422

Telephone: (805) 466-1717

MEDICAL EMERGENCY Phone: Poison Control Center

1-877-671-4608 (toll free) or 1-303-592-1711

TRANSPORT EMERGENCY Phone: CHEMTREC

1-800-424-9300 (toll free) or 1-703-527-3887

www.bsi-inc.com

Safety Data Sheet

Revision Number: 02.1 Issue date: 06/05/2015

1. PRODUCT AND COMPANY IDENTIFICATION

Product name: Mid-Cure™ IDH number: 203-204

Product type: 2-Part epoxy adhesive Item number: 203-204

Restriction of Use: None identified Region: United States

2. HAZARDS IDENTIFICATION

EMERGENCY OVERVIEW

WARNING: CAUSES SKIN IRRITATION

MAY CAUSE AN ALLERGIC SKIN REACTION

CAUSES SERIOUS EYE IRRITATION

HAZARD CLASS

HAZARD CATEGORY

SKIN IRRITATION

EYE IRRITATION

SKIN SENSITIZATION

PICTOGRAM(S)

Precautionary Statements

Prevention: Avoid breathing vapors. Wash thoroughly after handling. Use only outdoors or in a

well-ventilated area. Wear protective gloves, eye protection and face protection.

Response: IF ON SKIN: Wash with soap and water. IF INHALED: Remove person to fresh air and keep

comfortable for breathing.

IF IN EYES: Rinse with water for several minutes. If eye irritation persists: Get medical

attention. In c

ase of fire: Use water spray to extinguish.

IF INGESTED: Do not induce vomiting without medical advise.

Storage: Store in a well-ventilated place. Keep container tightly closed.

Keep in a cool and dry area.

Disposal: Dispose of contents and/or container according to Federal, State/Provincial

and local governmental regulations.

H-3, F-1, R-0

Classification complies with OSHA Hazard Communication Standard (29 CFR 1910.1200) and is consistent with the provisions of

the United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS).

Item number: 203-204 Product name: Mid-Cure™

Page 1 of 5

Summary of content (5 pages)

PAGE 1
Safety Data Sheet Revision Number: 02.1 Issue date: 06/05/2015 1. PRODUCT AND COMPANY IDENTIFICATION Product name: Mid-Cure™ Product type: 2-Part epoxy adhesive Restriction of Use: None identified Company address: Bob Smith Industries, Inc. 8060 Morro Road Atascadero, CA 93422 2.
PAGE 2
3. COMPOSITION / INFORMATION ON INGREDIENTS Hazardous Component(s) CAS Number Bisphenol A Epoxy Resin Aminoethylpiperazine Poly-Mercaptan Resin 25068-38-6 140-31-8 Proprietary Percentage* >45 <25 >23 * Exact percentage is a trade secret. Concentration range is provided to assist users in providing appropriate protections. 4. FIRST AID MEASURES Inhalation: Move to fresh air. Skin contact: Wash contact area with soap and water. Remove contaminated clothing. Launder contaminated clothing before use.
PAGE 3
For information on product shelf life contact BSI Customer Service at (800) 223-7699 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Employers should complete an assessment of all workplaces to determine the need for, and selection of, proper exposure controls and protective equipment for each task performed.
PAGE 4
. . 11. TOXICOLOGICAL INFORMATION Relevant routes of exposure: Skin, Inhalation, Ingestion, Eyes Potential Health Effects/Symptoms Inhalation: May cause respiratory tract irritation. Exposure to vapors above the established exposure limit results in respiratory irritation, which may cause headaches, dizziness, anesthesia and drowsiness. Is not a respiratory sensitizer. May cause skin irritation. Prolonged skin contact may cause burns. May cause sensitization of skin.
PAGE 5
Exceptions: Primary packs containing less than 500ml are unregulated by these modes of transport and may be shipped unrestricted. Marine pollutant mark is not required in sizes <5 L. Water Transportation (IMO/IMDG) Proper shipping name: Hazard class or division: Identification number: Packing group: Marine pollutant: Environ. Hazardous Substance, Liq, n.o.s. 9 3082 III Yes 15.