BOB LONG TECHNOLOGIES 925-625-7929 techsupport@boblongdirect.com www.boblongdirect.
WARNING! This paintball marker is not a toy. Misuse or mishandling can result in serious injury or death. Every person within range of a loaded paintball gun must wear eye protection specifically designed for paintball. It is recommended at least 18 years of age to purchase, 14 years old to use with adult supervision or 10 years old to use on paintball fields meeting ASTM standards F1777-97. Ensure you read entire instruction manual before operating your M-TAC.
Page CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
Contents WARRANTY ............................................................................................................................................. 5 THINGS THAT VOID YOUR WARRANTY..................................................................................................... 5 QUICK START GUIDE................................................................................................................................ 6 INTRODUCTION........................................................
WARRANTY Bob Long Technologies warrantees our markers against manufacturing defects. Electrical components are warranted for a period of 90 days. All solenoids and wire harnesses are tested for function prior to leaving our factory. Solenoids and wire harnesses will only be warranted at the discretion of Bob Long Technologies. Only use factory authorized lubricants when maintaining your marker. The use of nonauthorized lubricants or maintenance solutions will void your warranty.
Page 6 QUICK START GUIDE CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
Page CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
Page 8 INTRODUCTION CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
BASIC SPECIFICATIONS Classification: Configuration: Barrel Thread Type: Included Barrel: Included ASA: Intended Propellant: Intended Propulsion Speed: HPR magazine: LPR Pressure: Estimated Shot Count: Motherboard: 4C Eye Compatible: 4C Eye Equipped: Estimated Rate of Fire: Trigger Activation: Trigger Return: Trigger Adjustment: Page 9 Weight: Marq Tactical Series Electro-pneumatic. Open bolt. In-line poppet valve.
Page 10 MARKER DISASSEMBLY CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
Page CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
Page 12 HPR MAGAZINE MAINTENANCE CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
Page 13 LPR MAINTENANCE CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
Page 14 ANTI-CHOP EYE MAINTENANCE CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
Page 15 PROFICIENCY ENGINE DISASSEMBLY CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
Page 16 PROFICIENCY ENGINE LUBRICATION CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
MAINTENANCE SCHEDULE Mileage Recommended Upkeep • Clean and relube bolt o-rings • Inspect o-rings for damage • Clean and relube proficiency engine 10,000 Shots (5 Cases) • Repeat above steps • Clean, inspect, and regrease HPR Piston and o-rings • Clean, inspect, and regrease LPR Piston and o-rings 20,000 Shots (10 Cases) • Repeat above steps • Clean, inspect, and regrease poppet shaft o-ring Page 17 5,000 Shots (2.
CONSUMABLES LIST Part Name Front Of Stage 1 Shroud Mainbody To Stage 2 Shroud Assembly Specifications Quantity Stage 1 Shroud Fasteners 6-40 x ¼” Socket Head Cap Screw BO 10-32 x ¼” Low Head Socket Cap Screw Page 18 Stage 2 Shroud Assembly Fasteners Front Of Stage 2 Shroud Assembly 6-40 x ¼” Socket Head Cap Screw BO Left Side Stage 2 Accessory Rail To Stage 6-40 x ¼” Socket Head Cap Screw (BO) 2 Shroud Bottom Stage 2 Accessory Rail To Stage 2 6-40 x ¼” Socket Head Cap Screw (BO) Shroud Cap Right Side
Bottom Air Passage Plug Front Grip Frame To Mainbody Rear Grip Frame To Mainbody Part Name 10-32 x 3/8” Cup Point Socket Set Screw 18-8 SS 10-32 x ¼” Low Head Socket Cap Screw BO 10-32 x ¼” Low Head Socket Cap Screw BO 1 2 2 Specifications Quantity Page 19 Stage 1 Shroud Fasteners Mainbody to Back Block 10-32 x ¼’ Low Head Socket Cap Screw BO Stage 1 Proficiency Kit Fasteners Ram Housing to Back Block Mounting 8-32 x 1/8” Cup Point Socket Set Screw 18-8 SS Post Inline Regulator (HPR Magazine) Fasten
O-RING LIST Part Name Specifications Quantity Mainbody (Upper Receiver) Solenoid To Mainbody Seal Front, Outside Of Back Block Rear, Outside Of Blast Guide 1 x 3mm Buna (Durometer 70) Back Block 011 Buna (Durometer 70) Stage 1 Proficiency Kit 1mm x 12mm Buna (Durometer 70) 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 1 1 1 1 1 Page 20 Rear Bumper Of Quick Release Ram 007 Buna (Durometer 70) Square-ring Shaft Rear, Inside Of Poppet Shaft 008 Buna (Durometer 70) O-ring Rear, Outside Of Poppet Shaft 010 Buna (Durom
O-Ring Size Chart 007 008 010 014 015 016 020 012 022 Page 21 011 CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
QUESTIONS AND ANSWERS 1. Q: How does the M-TAC work? Open or closed bolt? Spool valve? Poppet valve? A: The Marq is a revolutionary electropneumatic inline poppet valve design. It is not a spool valve, nor is it a traditional stacked tube design--but rather a unique platform that is unlike nearly any other high end marker available. 2. Q: Where can I get repair parts\O-rings? A: Bob Long Technologies and authorized dealers stock replacement parts. 3.
7. Q: How do I use the Bob Long LPR tester? A: Note: Left facing gauge reads inline regulator (HPR) pressure. Rear facing gauge read LPR Pressure. Note: Lightly grease engine o-rings. Engine should slide in mainbody with minimal friction. If the engine becomes bound in any way an o-ring has probably been ruined. Replace o-ring and continue install until engine slides in smoothly. Page 23 1) De-gas your marker.
8. Q:What should my LPR/HPR pressure settings be? A:LPR 70-75psi. HPR 200psi for approximately 290 fps. These are the factory shipped pressures, as well as the approximations for 290 fps with a good paint to bore match. 9. Q:What should I do if my gun is leaking down the barrel? A:Remove the engine from the marker, and replace all the #22 o-rings on the outside of the engine (there's 6 of them).
tolerances built into the Bob Long Technologies products were specifically designed for o-rings treated with Dow 55. 15. Q: My left eye cover does not fit! What do I do? A: The hole in the eye cover is slightly off center. Make sure that it is toward the front of the marker and that the retaining screw for the left eye is in the hole toward the rear of the marker. 16. Q: What can I attach to the Picatinny rail system? A: Any accessory that uses this type of rail system.
Page 26 about 5,000 feet elevation. We didn’t have a light box handy and it was either use the wrap or keep propping pieces on the camel. CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR M-TAC. SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
