User's Manual

34
INTR ODUCTION
INTRODUCTION
The Intimidator is controlled via the MEMBRANE PAD located on the rear of the Trigger Frame. All of the functions of the Intimidator
can be easily accessed and changed through the Membrane Pad.
GETTING STARTED
To power up your Intimidator, Press the ON/OFF button. To turn off your Intimidator, press and hold ON/OFF button for approximately
1 second and release. Buttons 1 and 2 allow the user to scroll, select, adjust, and save settings through the menus as well as timer
activation, stop and reset. Pressing and holding buttons 1 and 2 simultaneously will open Menu Mode. Once in the Menu Mode, button
1 controls scrolling as well as the adjustments made to settings while button 2 controls selection and saving of menu settings. Every
Intimidator is equipped with an LCD screen, located on the side grip panel
(
left of the membrane pad
)
which allows the user to verify
menu settings along with voltage, timer, shot counter, eye status, tournament lock, and others, depending on the software version
installed on the circuit board. A detailed description of each function can be found in the Board Operation section.
NOTE
:
The Frenzy Board IS NOT Programmable via the trigger.
TRIGGER ADJUSTMENT
The trigger is fully adjustable using the three screws within the trigger. The upper screw controls the return spring tension, the
center screw adjusts micro-switch activation point and the lower screw adjusts the trigger stop point.
BARREL
The Intimidator comes standard with a one piece, .689 Bore, 12-inch Assassin barrel. Barrel threads for the Intimidator are
Auto-cocker type.
*
Weight of Marker without 12” Assassin Barrel is 1lbs., 13oz.
SPECIFICATIONS
Model . . . . . . . . . . . . . . . . . . . . . . . . .Empire 2 Intimidator
Caliber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Action . . . . . . . . . . . . . . . . . . . . . . . . . . .Electro-Pneumatic
Air Source . . . . . . . . . . . . . . . . . . .Compressed Air/Nitrogen
Battery Type . . . . . . . . . . . . . . . . . . . . . . . . . .9-Volt Battery
Cycle Rate . . . . . . . . . . . . . . . . . . . . .Unlimited Semi Mode
Effective Range . . . . . . . . . . . . . . . . . . . . . . . . . . .150+ feet
Weight . . . . . . . . . . . . . . . . . . . . . . . . . .2 pounds, 1 ounces
Length . . . . . . . . . . . . . . . . . . . . . .
(
12” barrel
)
18.25 inches
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.75 inches
WARNING!
Always ensure Marker is not shooting at a dangerous velocity. Ensure all participants are wearing the proper
Paintball safety equipment. You will be held liable if someone is hurt by a Paintball fired from your Marker
regardless of fault.
WARRANTY
B.L.A.S.T. warrantees the Intimidator against damages in Manufacturing Defects only. Electrical components are warranted for
a period of 90 days. Solenoids are not warranted. When utilizing after market Drop-Forwards ensure attachment bolts DO
NOT protrude into internal grip assembly. When utilizing aftermarket grips ensure attachment bolts DO NOT protrude
into internal grip assembly. Failure to do so may damage the internals and will result in void of warranty. Use of Teflon
tape will void warranty. Aftermarket anodizing will result in void of warranty.
For questions concerning your Intimidator manual please call [phone].
OPERATION
The Intimidator Marker is a solenoid controlled open-bolt design. The bolt is locked onto a dual pressurized machined slid-
er that is controlled by the solenoid (An electronic 4-way valve control). The back of the chamber is pressurized to move
the bolt forward, and the front is pressurized to move the bolt backward. This allows for very low cycling pressure, as well
as much less cocking recoil.
GENERAL DESCRIPTION
The Intimidator is a low pressure operating, open bolt, electronic Marker, featuring microchip managed solenoid control,
anti-chop eyes (ACE), dedicated low and high pressure regulators attached to a sculptured regulator mounting block,
and unique patent pending modular ram sleeve.
The field strippable pull pin bolt is connected to a dual pressurized sliding ram. This ram is held within the modular sleeve
located in the lower tube of the body. The low pressure regulator supplies air through the regulator mounting block to
the front barb of the solenoid. Upon activation, the solenoid redirects alternating pressure through the rear barbs, from
the chamber in front of the ram to the back chamber behind the ram. The forward shifting ram will then strike the poppet,
opening the main valve which releases high pressure regulated air up through the transfer port and into the upper tube of
the body. The pull pin connected bolt pushes the paintball into the breech while simultaneously redirecting the charge of air to
propel the projectile
(
paintball
)
to its target.
*
INTIMIDATOR
GEN4