Defiant 2 Manual ƒ 5/31/05 5:44 PM Page 1 O P E R ATO R S M A N UA L
Defiant 2 Manual ƒ 5/31/05 5:44 PM Page 3 Contents Table f T ao b le of Contents Section Safety Safet y Page Congratulations on your purchase of the DEFIANT 2 Paintball Marker. The DEFIANT 2 represents the latest in Paintball Marker technology at a very affordable price. Before operating your DEFIANT 2, please read the entire manual thoroughly. Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Warning .
Defiant 2 Manual ƒ 5/31/05 5:44 PM Page 5 WARNING Wa r n i ng INTRO Introduction Always ensure Marker is not shooting at a dangerous velocity. Ensure all participants are wearing the proper Paintball safety equipment. You will be held liable if someone is injured by a Paintball fired from your Marker regardless of fault. The DEFIANT 2 is controlled via the MEMBRANE PAD located on the rear of the Trigger Frame, as well as the Dip Switch Control Panel located on the front side of the Frenzy Board.
Defiant 2 Manual ƒ 5/31/05 5:45 PM Page 7 INTRO Introduction O PER AT ION continued Op e r at ion REGULATORS GAS CONFIGURATIONS Included with the DEFIANT 2 are 2 High-Flow Regulators. The Low Pressure Regulator (LPR) uses a standard 1/8 inch hex key for adjustment, while the High Pressure Regulator (HPR) uses a standard 3/16 inch hex key for adjustment. Turn the adjustment screw clockwise to increase pressure and counter-clockwise to decrease pressure.
Defiant 2 Manual ƒ 5/31/05 5:45 PM Page 9 E L E C T R O N I C S BOARD O PER AT ION Electronics Board Op e r at ion BATTERY INFORMATION GETTING STARTED The DEFIANT 2 uses a standard 9v battery. To change the battery, remove the Left Rubber Grip Panel, then remove the 4 allen screws securing the two Trigger Frame halves. You’ll notice the battery fits into the bottom of the grip frame. Disconnect the old battery and re-connect the new. Powering Up 1.
Defiant 2 Manual ƒ 5/31/05 5:45 PM Page 11 BOARD OPERATION B o a r d Op e r at ion INTRO continued Compe tition Lock MODE SELECTION (Version 127.4T FRENZY only) The LED FRENZY Board is driven via the Two-Button Membrane Pad on the rear of the Trigger Frame (figure “A”) as well as the On-Board Dip Switch Panel (figure “B”) located on the front side of the Fenzy Board and is accessed by removing the left trigger frame panel.
Defiant 2 Manual ƒ 5/31/05 5:46 PM Page 13 A S S E M& B L Y A s s e m b ly & D i s a s s e m b ly GETTING STARTED DISASSEMBLY I. TRIGGER FRAME DISASSEMBLY (continued) 8. Remove Eye Sensor Wire Harness. 9. Remove Circuit Board. 10. Remove Shouldered Trigger Retaining Screw and lift out Trigger and Trigger Return Spring. 11. Loosen Front Frame Retaining Screw. 12. Remove Rear Frame Retaining Screw. 13. Lift Out Front Hose from Around Hose Guard. (A small allen wrench works well) 14.
Defiant 2 Manual ƒ 5/31/05 5:46 PM Page 15 A S S E M& B L Y A s s e m b ly & D i s a s s e m b ly II. REGULATOR DISASSEMBLY 1. Remove High-Pressure Regulator to gain proper clearance to the LPR Retaining Screw. 2. Remove LPR Retaining Screw from Body. 3. Slide LPR Assembly from Body. HIGH-PRESSURE REGULATOR (HPR) 5. Remove ASA Receiver Retaining Screw. 6. NOTE: The Transfer Hole Screw will only need to be removed if a leak is detected, or a great deal of debris is present. 1.
Defiant 2 Manual ƒ 5/31/05 5:47 PM Page 17 A S S E M& B L Y A s s e m b ly & D i s a s s e m b ly III. BODY DISASSEMBLY First: Ensure Barrel of Marker is removed. a1. Remove both Eye Sensor Covers (one on each side) by removing Retaining Screw. a2. Remove both Eye Sensors (one on each side) by carefully pulling sensor heads from mounting holes. a3. Lift up on Bolt Retaining Pin and slide Bolt out of rear of Marker. 4a. Unscrew Encapsulated Ram Sleeve Assembly from Marker Body.
Defiant 2 Manual ƒ 5/31/05 5:47 PM Page 19 A S S E M& B L Y A s s e m b ly & D i s a s s e m b ly ASSEMBLY TIPS KEY ELEMENTS TO REMEMBER DURING ASSEMBLY. DISASSEMBLY GENERAL MAINTENANCE WARNING: NEVER use lightweight gun oil on Marker. Oil will destroy internals of Air Valve and O-rings. O-Rings: LUBRICATE ALL O-RINGS UPON INSTALLATION. Keep foreign obstructions out of Marker internals and Lubricate all O-rings within the Marker with a generous coat of Dow 55 Lubricant.
Defiant 2 Manual ƒ 5/31/05 5:47 PM Page 21 TROUBLESHOOTING Troubleshooting TROUBLESHOOTING NOTE: Refer to Assembly/Disassembly to perform repairs indicated below. PROBLEM DIAGNOSIS REPAIR PROBLEM DIAGNOSIS REPAIR Marker leaks down Barrel 1. Poppet is not sealing 2. Ram Sleeve O-rings are damaged 1. Replace Poppet 2. Replace Ram Sleeve O-rings LPR spikes 1. LPR Base 0-rings are bad 2. Regulator Seat is bad 3. Brass Nut isn’t tight enough 4. 010 0-ring on Brass Nut is worn or damaged 1.
Defiant 2 Manual ƒ 5/31/05 5:47 PM Page 23 T E C.H N.I C .
Defiant 2 Manual ƒ 5/31/05 5:47 PM Page 25 T E C.H N.I C .
Defiant 2 Manual ƒ 5/31/05 5:47 PM Page 27 P A R T S C H EC K L I S T Pa r t s C h e c k l i s t 75 1 2 3 73 4 5 6 7 8 9 10 11 32 12 13 33 14 15 16 17 72 18a PARTS CHECKLIST Designed by Robert Rivera - 305.819.1009 74 1. LPR Adjustment Screw 32. Eye Cover Retaining Screws 2. LPR Front End Cap 33. Eye Covers 3. LPR Spring Washer 34. Eye Wire Harness 4. LPR Spring 35. Valve Retaining Screw 5. LPR Piston 36. Grip Mounting Screws 6. LPR Piston O-Rings (011) 37a.
