User's Manual
B
B
o
o
b
b
L
L
o
o
n
n
g
g
i
i
n
n
t
t
i
i
m
m
i
i
d
d
a
a
t
t
o
o
r
r
B
B
o
o
b
b
L
L
o
o
n
n
g
g
i
i
n
n
t
t
i
i
m
m
i
i
d
d
a
a
t
t
o
o
r
r
Electronics
Battery Information
The Intimidator uses a standard 9v battery. To change the battery, remove the Grip,
then remove the 4 allen screws securing the two grip halves. You’ll notice the battery fits
into the bottom of the grip frame. Disconnect the old battery and re-connect the new.
WARNING!
At this time it is good to verify screws are not protruding through the bottom of the grip
and into the interior components. Failure to do so may result in damage to the battery
and/or Circuit Board.
ANTI-CHOP EYES
(
ACE
)
The Intimidator is the first Production Marker to incorporate a break beam Anti-Chop Eye
system in a Production Marker, commonly referred to as the ACE system. The ACE system
consists of a set of sensors mounted near the bottom of the breech to restrict firing until a
ball is completely loaded into the breech. Always operate the Intimidator with the eyes on.
Failure to do so will more than likely result in broken paint in the breech. The transmitter eye
can be identified by the red and black wires, metal casing and male connector. The receiver
eye can be identified by it’s blue and black wires, black plastic casing and female connector.
Factory Settings
Standard factory FRENZY Board settings are as follows:
DWELL . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ms
EYE . . . . . . . . . . . . . . . . . . . . . . . . . . . Delay
BIP . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 ms
BOL
T DELA
Y . . . . . . . . . . . . . . . . . . . . . 15ms
TIMER
. . . . . . . . . . . . . . . . . . . . . . . . .
10.00
DEBOUNCE . . . . . . . . . . . . . . . . . . . . .
12 ms
MBOUNCE
. . . . . . . . . . . . . . . . . . . . . . . . . . 2
DELA
Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
A detailed description of each function is in the board operation section.
Board Operatio
n
Getting Started
POWERING UP
1. To power up your Intimidator, press the ON/OFF button.
2. To turn off your Intimidator, press and hold ON/OFF button for approximately 1 second.
The LCD will show
[
TURNING OFF
]. After 1 second the screen will go blank.
Release the ON/OFF Button. Your Intimidator is now OFF.
LIQUID CRYSTAL DISPLAY
(
LCD
)
Once the Marker is powered up, the LCD will display codes representing the status of the Marker.
The codes are located on the 2nd line of the LCD and are as follows:
Standard Operation Modes
1.
[
F
]
- Indicates FORCED Mode
2.
[
D
]
- Indicates DELAY Mode
3.
[
S
]
- Indicates DRY FIRE Mode
(
Formerly known as SIMULATION Mode. Demonstrates how the Marker should
operate with an appropriate supply of paintballs and fully charged air system.
)
Non-Standard Operation Modes/Warnings
4.
[
*
]
- Indicates EYE SENSOR MALFUNCTION
(
Marker will be limited to 12bps
)
5.
[
C
]
- Indicates COMPETITION Mode is ON
6.
[
B
]
- Indicates BATTERY IS LOW
Views of each mode selection on the Circuit Board can be seen below.
FORCED Mode DELAY Mode DRY FIRE Mode
EYE SENSOR MALFUNCTION COMPETITION Mode ON BATTERY IS LOW
2005
87
123
456
Bob Long Manual ƒ 4/20/05 4:58 AM Page 10