User's Manual

B
B
o
o
b
b
L
L
o
o
n
n
g
g
i
i
n
n
t
t
i
i
m
m
i
i
d
d
a
a
t
t
o
o
r
r
B
B
o
o
b
b
L
L
o
o
n
n
g
g
i
i
n
n
t
t
i
i
m
m
i
i
d
d
a
a
t
t
o
o
r
r
2005
WARNING!
Make sure Marker is not shooting at a dangerous velocity. Ensure all participants
are wearing the proper Paintball safety equipment. You will be held liable if someone
is hurt by a Paintball fired from your Marker regardless of fault.
WARRANTY
B.L.A.S.T. warrantees the Intimidator against damages in Manufacturing Defects only.
Electrical components are warranted for a period of 90 days. Solenoids are not warranted.
When utilizing after market Drop-Forwards ensure attachment bolts DO NOT protrude
into internal grip assembly. When utilizing aftermarket grips ensure attachment bolts
DO NOT protrude into internal grip assembly. Failure to do so may damage the internals
and will result in void of warranty. Use of Teflon tape will void warranty. Aftermarket
anodizing will result in void of warranty.
For questions concerning your Intimidator manual please call [phone].
OPERATION
The Intimidator Marker is a solenoid controlled open-bolt design. The bolt is locked
onto a dual pressurized machined slider that is controlled by the solenoid (An electronic
4-way valve control). The back of the chamber is pressurized to move the bolt forward,
and the front is pressurized to move the bolt backward. This allows for very low cycling
pressure, as well as much less cocking recoil.
GENERAL DESCRIPTION
The Intimidator is a low pressure operating, open bolt, electronic Marker, featuring
microchip managed solenoid control, anti-chop eyes (ACE), dedicated low and high
pressure regulators attached to a sculptured regulator mounting block, and unique
patented pending modular ram sleeve.
The field strippable pull pin bolt is connected to a dual pr
essurized sliding ram. This ram
is held within the modular sleeve located in the lower tube of the body. The low pressure
regulator supplies air through the regulator mounting block to the front barb of the
solenoid. Upon activation, the solenoid redirects alternating pressure through the rear
barbs, from the chamber in front of the ram to the back chamber behind the ram. The
forward shifting ram will then strike the poppet, opening the main valve which releases
high pr
essure regulated air up through the transfer port and into the upper tube of the
body
. The pull pin connected bolt pushes the paintball into the br
eech while simultaneously
redirecting the charge of air to propel the projectile
(
paintball
)
to its target.
Introduction
The Intimidator is controlled via the MEMBRANE PAD located on the rear of the grip
frame. All of the functions of the Intimidator can be easily accessed and changed through
the Membrane Pad.
GETTING STARTED
To power up your Intimidator, Press the ON/OFF button. To turn off your Intimidator,
press and hold ON/OFF button for approximately 1 second. Buttons 1 and 2 allow the
user to scroll, select, adjust, and save settings through the menus as well as timer
activation, stop and reset. Pressing and holding buttons 1 and 2 simultaneously will
open Menu Mode. Once in the Menu Mode, button 1 controls scrolling as well as the
adjustments made to settings while button 2 controls selection and saving of menu
settings. Every Intimidator is equipped with an LCD screen, located on the side grip
panel
(
left of the membrane pad
)
which allows the user to verify menu settings along
with voltage, timer, shot counter, eye status, tournament lock, and others, depending on
the software version installed on the circuit board. A detailed description of each function
can be found in the
Board Operation section.
NOTE: The Frenzy Board IS NOT Programmable via the trigger.
TRIGGER ADJUSTMENT
The trigger is fully adjustable using the three screws within the trigger. The upper
screw controls the return spring tension, the center screw adjusts micro-switch activation
point and the lower screw adjusts the trigger stop point.
BARREL
The Intimidator comes standard with a one piece, .689 Bore, 12-inch Assassin barrel.
Barrel threads for the Intimidator are Auto-cocker type.
SPECIFICATIONS
Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Alias Intimidator
Caliber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Electro-Pneumatic
Air Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Compressed Air/Nitrogen
Battery Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-Volt Battery
Cycle Rate
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unlimited Semi Mode
Effective Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150+ feet
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 pounds, 10 ounces
Length
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(12” bar
r
el) 20 inches
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10.5 inches
43
Bob Long Manual ƒ 4/20/05 4:58 AM Page 6