Bob Long Manual ƒ 4/20/05 4:41 AM Page 1 2005 O p e r a t o r s 1799 Carpenter Road Oakley, California 94561 M a n u a l
Bob Long Manual ƒ 4/20/05 4:58 AM Page 4 BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r 2005 Ta bl e o f Section Congratulations on your purchase of the Intimidator Paintball Marker. The Intimidator represents the latest in Paintball Marker technology at a very affordable price. Before operating your Intimidator, please read the entire manual carefully. Co n t e n ts Page Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bob Long Manual ƒ 4/20/05 4:58 AM Page 6 BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r 2005 WA R N I N G ! Introduction Make sure Marker is not shooting at a dangerous velocity. Ensure all participants are wearing the proper Paintball safety equipment. You will be held liable if someone is hurt by a Paintball fired from your Marker regardless of fault. The Intimidator is controlled via the MEMBRANE PAD located on the rear of the grip frame.
Bob Long Manual ƒ 4/20/05 4:58 AM Page 8 BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r 2005 Operation I n t r o d u c t i o n (continued) Gas Configurations REGULATORS Included with the Intimidator are 2 High-Flow Regulators. Both regulators use a standard 3/16 inch hex key for adjustment. Turn the adjustment screw clockwise to increase pressure and counter-clockwise to decrease pressure.
Bob Long Manual ƒ 4/20/05 4:58 AM Page 10 BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r 2005 Board Operation Electronics Getting Started Battery Information The Intimidator uses a standard 9v battery. To change the battery, remove the Grip, then remove the 4 allen screws securing the two grip halves. You’ll notice the battery fits into the bottom of the grip frame. Disconnect the old battery and re-connect the new. POWERING UP 1. To power up your Intimidator, press the ON/OFF button. 2.
Bob Long Manual ƒ 4/20/05 4:58 AM Page 12 BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r 2005 Board Operation Board Operation TO ACTIVATE COMPETITION LOCK: Getting Started 1. Turn Marker OFF. 2. Open up Trigger Frame to gain access to the Circuit Board. 3. Short out C and D Terminals (holes) of the top of the board. Paper clips work well for this. Bend the clip so that one end is touching the D and the other end is touching C. 4a. Turn Marker ON. 4b.
Bob Long Manual ƒ 4/20/05 4:59 AM Page 14 BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r 2005 Assembly and Disassembly Assembly and Disassembly TRIGGER DISASSEMBLY (continued) Getting Started 7. Remove 2 Board retaining screws. (1 1/16 Allen Head screw and 1 Phillips Head screw) 8. Flip Board over towards left side. 9. Lift up on black LCD ribbon locks located on each side of membrane ribbon harness and remove complete membrane assembly from trigger frame. 10. Remove Eye Sensor Wire Harness. 11.
Bob Long Manual ƒ 4/20/05 4:59 AM Page 16 BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r 2005 Assembly and Disassembly Assembly and Disassembly II. REGULATOR DISASSEMBLY REGULATOR DISASSEMBLY (continued) ASA BLOCK/HOUSING TORPEDO/HIGH-PRESSURE REGULATOR (HPR) First: Remove Both Regulators. 1. Unscrew Allen Adjuster. 6. Remove Pin Valve Retainer. 1. Remove Air Barb from ASA Block.* 2. Unscrew Lower End of (HPR) High-Pressure Regulator Housing. 7. Remove Teflon Washer. 2.
Bob Long Manual ƒ 4/20/05 4:59 AM Page 18 BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r 2005 Assembly and Disassembly Assembly and Disassembly III. BODY DISASSEMBLY BODY DISASSEMBLY (continued) First: Ensure Barrel of Marker is removed. 1. Remove both Eye Sensor Covers (one on each side) by removing Retaining Screw. 8. Remove Air Barb from Back of Ram Sleeve. Do not lose fiber washer at base of Air Barb. 9. Remove Ram Sleeve retaining allen. 2.
Bob Long Manual ƒ 4/20/05 4:59 AM Page 20 BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r 2005 Assembly and Disassembly Maintenance ASSEMBLY TIPS GENERAL MAINTENANCE KEY ELEMENTS TO REMEMBER DURING ASSEMBLY. WARNING: NEVER use lightweight gun oil on Marker. Oil will destroy internals of Air Valve and O-rings. O-Rings: LUBRICATE ALL O-RINGS UPON INSTALLATION. Ram Sleeve O-rings: Always ensure all O-Rings are in good condition upon install.
Bob Long Manual ƒ 4/20/05 4:59 AM Page 22 BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r 2005 Troubleshooting Troubleshooting NOTE: Refer to Assembly/Disassembly to perform repairs indicated below. Marker leaks down Barrel 1. Poppet is not sealing 2. Ram Sleeve O-rings are damaged 3. Poppet O-ring is damaged 1. Replace Poppet 2. Replace Ram Sleeve O-rings 3. Remove LPR Block and replace Poppet o-ring Marker leaks from inside Trigger Frame 1. Air Hose has become disconnected 2.
Bob Long Manual ƒ 4/20/05 4:59 AM Page 24 BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r 2005 Technical Specs Technical Specifications PARTS IDENTIFICATION O-ring Sizer/Identifier O-ring & Size Quantity Discription/Breakdown 1 Per Marker Poppet O-ring O-ring (actual size) Quantity Discription/Breakdown 1 Per Marker LPR Base “Square Cut” Outer Most O-ring 7 Per Marker 4 - Bolt O-rings 2 - Regulator/ASA Block O-rings 1 - Torpedo Upper End O-ring 1 Per Marker FRONT Ram Sleeve O-ring 1
Bob Long Manual ƒ 4/20/05 4:59 AM Page 26 BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r 2005 Technical Specs Technical Specifications PARTS IDENTIFICATION (continued) Screw Sizer/Identifier Screw & Size Quantity 4 Per Marker 6/32 x 3/16 (Stainless Steel) Discription/Breakdown Rubber Grip Screws 1 Per Marker Trigger Mounting Screw (Stainless Steel) (Secures Trigger to frame) 2 Per Marker Eye Cover Screws 1 Per Marker Retaining Set Screw for Bolt Pull Pin 1 Per Marker ASA Block Set