DWA_5_2_eng.book Seite 41 Dienstag, 1.
DWA_5_2_eng.book Seite 42 Dienstag, 1. März 2005 4:59 16 Note: d Warning: This symbol indicates precautions and measures which are essential in order to protect the rider and other persons from possibly severe or fatal injury. e Attention: Special instructions and precautions intended to avoid damage to the motorcycle. Non-compliance can void the guarantee. L Note: Specific instructions on how to operate, control, adjust or look after items of equipment on the motorcycle.
DWA_5_2_eng.book Seite 43 Dienstag, 1. März 2005 4:59 16 1 Details described or illustrated in this booklet may differ from the motorcycle’s actual specification as purchased, the accessories fitted or the national-market specification. No claims will be entertained as a result of such discrepancies. Dimensions, weights, fuel consumption and performance data are quoted to the customary tolerances. The right to modify designs, equipment and accessories is reserved. Errors and omissions excepted.
DWA_5_2_eng.book Seite 44 Dienstag, 1. März 2005 4:59 16 BMW recommends Castrol BMW Motorrad Order No.: 01 41 7 695 361 01.
DWA_5_2_eng.book Seite 1 Dienstag, 1. März 2005 4:59 16 Welcome to BMW i Introduction 1 Welcome to BMW Your authorised BMW motorcycle dealer will be glad to assist you in all matters relating to your motorcycle. We hope you will enjoy familiarising yourself with these instructions for use, and we would like to take this opportunity of sending you our very best wishes. Congratulations on your purchase of this BMW anti-theft alarm.
DWA_5_2_eng.book Seite 2 Dienstag, 1. März 2005 4:59 16 Contents i Introduction 2 5 Lights i Introduction Lights.................................. 23 Welcome to BMW ................. 1 General ................................. 3 6 Programming Customising the anti-theft 1 Overview and operation alarm system ...................... 24 Controls ................................ 4 Default settings ................... 25 Functions of the remote Accessing the control unit ............................
DWA_5_2_eng.book Seite 3 Dienstag, 1. März 2005 4:59 16 General i Your anti-theft alarm is combined with a central locking system that enables you to open and close the cases, the topcase, and the radio compartment by remote control. It also enables you to switch on the map-reading light and the Any attempt to move the motor- ground lights automatically.
DWA_5_2_eng.book Seite 4 Dienstag, 1. März 2005 4:59 16 Controls 1 2 1 3 Overview and operation 4 4 5 L 1 2 3 4 5 Left button (ribbed) Right button LED Radio remote control unit Status LED (on the vehicle) Note: Do not be tempted to use the remote control unit to lock the keys inside a stowage compartment.
DWA_5_2_eng.book Seite 5 Dienstag, 1.
DWA_5_2_eng.book Seite 6 Dienstag, 1. März 2005 4:59 16 Code card 1 Overview and operation 6 1 2 The code number is stamped in encrypted form on the anti-theft The anti-theft alarm is supplied alarm and it is also printed on complete with a sealed envean adhesive label 2 supplied lope containing a code card 1. with the anti-theft alarm. You The number stated on the code should affix the label at a concard (remove the adhesive cealed location on the motorcylabel) is the code for deactivat- cle.
DWA_5_2_eng.book Seite 7 Dienstag, 1. März 2005 4:59 16 Activation 1 2 2 Once the immobiliser has been activated the engine will refuse to start even if an authorised key is used for the start attempt. You can tell whether the immobiliser is activated by switching on the ignition and observing LED 5; if the immobiliser is active it will light up when the pre-ride check completes. Activation L Note: The remote control unit activates both the immobiliser and the alarm function.
DWA_5_2_eng.book Seite 8 Dienstag, 1. März 2005 4:59 16 Activation 2 Immobiliser 8 If confirmation takes the form of the alarm tone sounding four Activation of the immobiliser times, this is to indicate that the after ignition off but without anti-theft alarm's internal activation of the alarm function rechargeable battery is disis confirmed charged.
DWA_5_2_eng.book Seite 9 Dienstag, 1. März 2005 4:59 16 Deactivation 1 2 2 Immobiliser 9 Deactivating the immobiliser with the remote con- If confirmation takes the form of the alarm tone sounding four trol unit The immobiliser is deactivated • by pressing button 2 on the remote control unit once (if the immobiliser was activated automatically beforehand when you switched off the ignition, it is reactivated 30 seconds later).
DWA_5_2_eng.book Seite 10 Dienstag, 1. März 2005 4:59 16 Activation 1 2 3 Alarm function 10 Activation with motion sensor The alarm function is activated • by pressing button 1 on the remote control unit twice or • by switching off the ignition, if programmed (b 25) When you switch off the ignition, 50 seconds elapse before activation. The central locking system is not activated.
DWA_5_2_eng.book Seite 11 Dienstag, 1. März 2005 4:59 16 Activation 3 Alarm function 11 Deactivating the motion sensor You deactivate the motion sensor • by pressing button 1 on the remote control unit for a second time within the activation phase (b 12) If, for example, you want to transport your motorcycle by train, it is advisable to deactivate the motion sensor. Severe movements while the motorcycle is in transit could trigger a false alarm.
dwa_3_alarmfunktion_eng.fm Seite 12 Donnerstag, 10. März 2005 11:04 11 Activation phases 3 Alarm function 12 15 seconds elapse before the alarm function is fully active. Status of the antitheft alarm LED Activation phase (15 seconds) Rapid flashing (0.1 sec. on/ 0.5 sec. off) If the motion sensor was switched off: Rapid flashing (0.1 sec. on/ 0.2 sec. off) Anti-theft alarm active Slow flashing (0.1 sec. on/ 0.9 sec.
DWA_5_2_eng.book Seite 13 Dienstag, 1. März 2005 4:59 16 How the alarm is triggered 1 2 3 Alarm function 13 Alarm How the alarm is triggered The alarm can by triggered • by the motion sensor • by an attempt to switch on the ignition without deactivating the anti-theft alarm beforehand • by disconnection of the antitheft alarm from the motorcycle's battery (the anti-theft alarm's internal battery cuts in to supply power) An alarm lasts for 26 seconds.
DWA_5_2_eng.book Seite 14 Dienstag, 1. März 2005 4:59 16 Deactivation 1 2 3 Alarm function 14 Deactivating the alarm function with the remote control unit The alarm function is deactivated • by pressing button 2 on the remote control unit once If the alarm function was activated automatically beforehand when you switched off the ignition, it is reactivated 30 seconds later.
DWA_5_2_eng.book Seite 15 Dienstag, 1. März 2005 4:59 16 Deactivation Deactivating the alarm function without remote control unit 15 L Note: The system will permit a maximum of 3 successive attempts; if the third attempt in succession is unsuccessful the antitheft alarm engages for 10 minDeactivation is confirmed utes. The cases remain locked • by the turn indicators flashing when the system is deactivated once without the remote control unit.
DWA_5_2_eng.book Seite 16 Dienstag, 1. März 2005 4:59 16 Reasons for an alarm 3 Alarm function 16 Reasons for an alarm Once you have deactivated the alarm function, the LED shows you reasons for alarms, if any, that were triggered in your absence: • Flashes 1x: Motion sensor • Flashes 2x: Ignition on while the anti-theft alarm was primed • Flashes 3x: Anti-theft alarm disconnected from motorcycle battery The LED ceases to output this signal after 1 minute, or as soon as you switch on the ignition.
DWA_5_2_eng.book Seite 17 Dienstag, 1. März 2005 4:59 16 Reasons for an alarm 3 Alarm function 17 You can also check the system at some subsequent time in order to ascertain the reason why the most recent alarm was triggered. In order to do so, you must first identify yourself by means of your code number. If you now switch off the ignition, the LED will flash to indiIf the code number you entered cate once the reason for the most recent alarm, if any.
DWA_5_2_eng.book Seite 18 Dienstag, 1. März 2005 4:59 16 Reasons for an alarm 3 Alarm function 18 Step Action Confirmation 1 Deactivate the anti-theft alarm and switch on the ignition 2 Within 4 seconds, switch the LED on, ignition off and immediately on 1x acknowledgement again THREE TIMES in succes- tone sion 3 Switch the ignition off within 15 LED flashes seconds and then observe the LED 4 Count the LED flashes until the number corresponds to the first digit of your code number.
DWA_5_2_eng.book Seite 19 Dienstag, 1. März 2005 4:59 16 Manual operation 4 Central locking system 19 Manual opening and closing You can still open and close the cases, the topcase and the radio compartment manually with the key, as described in the Rider’s Manual.
DWA_5_2_eng.book Seite 20 Dienstag, 1. März 2005 4:59 16 Remote control unit 1 2 4 Central locking system 20 Opening with the remote control unit Press button 2 on the remote control unit once to unlock the cases, the topcase and the radio compartment.
DWA_5_2_eng.book Seite 21 Dienstag, 1. März 2005 4:59 16 Emergency unlocking 4 Central locking system 21 If the compartments were locked by the central locking system and, for some reason, the remote control unit is not to hand, you can use the emergency unlocking routine to open them. Emergency unlocking is independent of the current status of the lock barrel. You cannot use the emergency unlocking routine to open the radio compartment. 1 Insert the ignition key into the lock you want to open.
DWA_5_2_eng.book Seite 22 Dienstag, 1. März 2005 4:59 16 Safety shutdown 4 Central locking system 22 Overly frequent locking and unlocking within a short period of time could cause the motors of the central locking system to become very warm. An override function can cut in and interrupt operation in order to avoid damage to the motors: these interruptions can last for a maximum of 30 seconds.
DWA_5_2_eng.book Seite 23 Dienstag, 1. März 2005 4:59 16 Lights 1 a b c 5 Lights 23 The lights are switched on • when you deactivate the alarm function or • by switching off the ignition, if programmed (b 26) Map-reading light The map-reading light switches on automatically if switch 1 is in The lights dim out after position c. 20 seconds.
DWA_5_2_eng.book Seite 24 Dienstag, 1.
DWA_5_2_eng.book Seite 25 Dienstag, 1.
DWA_5_2_eng.book Seite 26 Dienstag, 1.
DWA_5_2_eng.book Seite 27 Dienstag, 1. März 2005 4:59 16 Programming The number of times LED 5 flashes indicates the step to which you have progressed in programming. An alarm tone sounds as confirmation when you press button 1, whereas an acknowledgement tone sounds when you press button 2. The LED stops flashing and four acknowledgement tones sound when you complete the final step.
DWA_5_2_eng.book Seite 28 Dienstag, 1. März 2005 4:59 16 Exiting programming mode 6 Programming 28 L Note: Note that you cannot activate the function for priming the alarm automatically when the Programming is saved • by switching off the ignition ignition is switched off unless after the final step is comthe system is also set up for aupleted tomatic activation of the immoor biliser.
DWA_5_2_eng.book Seite 29 Dienstag, 1. März 2005 4:59 16 Registering remote control units 7 Remote control units 29 If you want to start using an extra remote control unit or replace a remote control unit that has been mislaid, you always have to register all the remote control units with the anti-theft alarm. You can register a maximum of four remote control units.
DWA_5_2_eng.book Seite 30 Dienstag, 1. März 2005 4:59 16 Registering remote control units 7 Remote control units 30 Starting point You must begin by identifying yourself by means of your code number. Step If the code number you entered is correct, two acknowledgement tones sound to indicate that identification is completed.
DWA_5_2_eng.book Seite 31 Dienstag, 1. März 2005 4:59 16 Registering remote control units 1 2 7 31 Remote control units 3 You can now register a maximum of four remote control units with the anti-theft alarm. Step 1 Action Confirmation Press and hold down buttons 1 LED 3 flashes and 2 2 LED stops flashing after 10 seconds 3 Release buttons 1 and 2 LED ON 4 Press button 1 or 2 1x alarm, LED off 5 Repeat steps 1 - 4 for each additional remote control unit you want to register.
DWA_5_2_eng.book Seite 32 Dienstag, 1. März 2005 4:59 16 Exiting registration mode 7 Remote control units 32 Registration terminates • once four remote control units have been registered • if the ignition is switched off • if, after a remote control unit has been registered, 30 seconds elapse without a button being pressed The LED flashes and the acknowledgement tone sounds three times when registration ends.
DWA_5_2_eng.book Seite 33 Dienstag, 1. März 2005 4:59 16 Synchronising the remote control unit 1 2 7 Synchronisation is necessary if the buttons on the remote control unit are pressed more than 256 times outside the range of the receiver. When this limit is reached the receiver on the motorcycle no longer reacts to signals from the remote control unit.
DWA_5_2_eng.book Seite 34 Dienstag, 1. März 2005 4:59 16 Changing the battery 1 2 8 Care and maintenance 34 3 4 e Attention: Use only CR 2032 3V lithium batteries. The batteries in the remote con- Take care not to reverse polarity when inserting the batteries. trol units are due for replacement after approximately 2 to 3 Inserting batteries of a different years.
DWA_5_2_eng.book Seite 35 Dienstag, 1. März 2005 4:59 16 Changing the battery 6 7 8 8 10 9 • Remove screw 6 and lift off the bottom section of housing 7 • Slide the spent battery 10 out from underneath retainer 8 and insert the new battery – making sure the positive terminal is up • Place the bottom section of the housing on projection 11 • You do this by holding the at the front edge and close remote control unit within the the housing.
DWA_5_2_eng.book Seite 36 Dienstag, 1. März 2005 4:59 16 Technical data 9 Technical data 36 Anti-theft alarm Neutral activation time 15 seconds Alarm duration 26 seconds Neutral time between two consecutive alarms 10 seconds Operating temperature –40 °C to +85 °C Trigger angle of the motion sensor ±0.7° Current consumption (idle current with system active) < 3 mA Operating voltage 9–16 V Remote control unit Range of the remote control unit approx. 10 m Transmission frequency 433.
DWA_5_2_eng.book Seite 37 Dienstag, 1.
DWA_5_2_eng.book Seite 38 Dienstag, 1.
DWA_5_2_eng.book Seite 39 Dienstag, 1.
DWA_5_2_eng.book Seite 40 Dienstag, 1.
