Quick Start
Appearance
1. Signal Indicator Green: Connected to 4G network Blue: Connect to 3G network Red: No Signal or SIM card is not recognized, etc . 2. WiFi Indicator ● Blue: WiFi Signal is activate 3. SMS Indicator ● Blinking Blue: Have Unread SMS 4. Battery Indicator ● Green: Sufficient Battery ● Blinking green: Charging the battery ● Red: Low Battery ● Blinking Red: Device will power off soon. 5.
7. Power Button Press and hold to turn your 4G Hotspot on or Off 8.
WiFi Connection The default SSID(WiFi network name)and WiFi network key are printed on the4G Hotspot Label We strongly recommend that you change the default SSID and WiFi key to keep your data secure ☆ You can manage your4G hotspot through the Web Interface at http://192.168.0.1.
☆ The default username and password is admin. Click the online help on the web interface to learn more about your4G Hotspot. After installation of driver, you can access to Web Interface http://192.168.0.1 Charging Please only use a charger that is compatible with your4G Hotspot. The use of an incompatible charger may cause the device to malfunction, fail, or could even cause a fire. Such use voids all warranties, whether expressed or implied, on this product. ☆ The charger is an optional accessory.
To buy a charger, please contact an authorized retailer. Connecting to the Internet Using an LTE, 3Gnetwork The4G Hotspot’s management parameters have been preset according to your operator’s requirements. If data is transmitted, the4G Hotspot will automatically connect to the internet. If data is not transmitted for a period of time, the4G Hotspot will automatically disconnect from the network connection.
Logging into the Web Management page ☆Make sure that the connection between the 4G Hotspot and the device used to access the Internet, is working normally. ☆Open the browser on your device and enter http://192.168.0.1 in the address box . ☆Enter your username and password to log into the web management page. If you have any difficulty please contact customer care.
Please note: The default username is admin The default password is admin Restoring to Factory Settings If you forget the username, password, or SSID you have set, you can restore the settings on the web management page to the default factory settings. To do so, simply press and hold the RESET button until the 4G Hotspots restarts.
use it. The default SSID and password are printed on 4G Hotspot’s label, inthe battery slot of the device. Enable SD card sharing *In HTTP Share Mode, the device only supports FAT/FAT32 file system. *HTTP Share Mode: Share SD card via web browser.
card via USB port will be disabled. *USB Access Only: By the removable drive mapping, user can access SD card *via USB cable only. The web page of sharing SD card will be disabled. *Path to Share: You can input the sharing path, such as /Picture. By typing only, a slash in Path to Share filed, you agree to share entire SD card. *Path to Share can't be a dot, and can't contain following characters: <> " ' & + / \: * | #?~` Tips:
◇ ◇ ◇ ◇ ◇ Why isn’t my 4G Hotspot responding? Try restarting the device. If that doesn’t work, restore the device to its factory settings Why can’t I connect to my4G Hotspot sometimes? To save Power, your4G Hotspot’s WiFi auto off feature is designed to turn off WiFi when there haven’t been connections for a while. You can press the power button to turn on WiFi again.
◇ Charge your4G Hotspot for a While and Power it back on. Why did my4G Hotspot power off all of a sudden ? Your4G Hotspot may overheat when you use it continuously over a long period of time, and thereby trigger its automated protection system. WiFi will be turn off and your4G Hotspot will power off if this occurs. Please ensure the device is properly ventilated and cooled before you power it on again. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE .
Operation System Support OS Windows 7 32/64-bit Yes OS Windows 8 32/64-bit Yes OS Windows 8.1 32/64-bit Yes OS Windows 10 32/64-bit Yes OS Windows 10.7 32/64-bit Yes OS Windows 10.8 32/64-bit Yes OS Windows 10.9 32/64-bit Yes OS Windows 10.10 32/64-bit Yes OS Windows 10.11 32/64-bit Yes The list is subject to change without prior notice.
.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105 Information to the user.
-Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Absorption Rate (SAR) information: This MIFI meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies.
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset,including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may notcomply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
