BLY1 Barcode 5397007039283 Wireless Alarm System.
Getting started... BLY1 Wireless Alarm System Let’s get started... These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. Getting started... Introduction and Safety Overview of System Planning your Installation Installing your System In more detail...
Type box Introduction and Safety Getting started... 3 Overview of System 4-5 Planning your Installation 6-8 Installing your System Getting started... BLY1 Wireless Alarm System 9-15 2 Wireless Alarm System.
Introduction & Safety BLY1 Wireless Alarm System INTRODUCTION The wireless alarm system is designed to protect your home. It is a simple to use, easy to install unit. No special tools or training are required, all fixings are included. Getting started... IE IMPORTANT: Please read this manual carefully, in full, before commencing installation. You will find installation easier if you follow these steps in the sequence shown.
Overview of System BLY1 Wireless Alarm System This wireless alarm system is based on wireless radio technology to give exceptional levels of protection and reliability. It has the ability to control up to eight detectors, three remote keys (optional accessory) and one wireless siren. Kit Contents POWER TAMPER 3 2 6 5 4 9 8 7 0 m Anti-Ja On/Off Learn m Part-Ar Reset Arm Control Unit This is the heart of the system.
Overview of System BLY1 Wireless Alarm System System features • Detector /Key /External Siren learning – Every wireless device (detector, Key, External Siren) contains an unique identification code. During installation, the control unit will learn which devices belong within your system by receiving coded radio transmissions from each detector. Getting started... • This system can control up to eight detectors (every zone can control one wireless detector.
BLY1 Wireless Alarm System Planning your Installation Location of components Control unit – Location In choosing a suitable location you should bear in mind: • The need to reach the control unit easily, within the 30 seconds, when entering and leaving the premises, ideally passing only one detector. Getting started... • The control unit should not be visible from the exterior of the protected premises.
Planning your Installation BLY1 Wireless Alarm System Planning the location of system components Example of a domestic layout The 2 sample layouts below are intended as guides only but demonstrate two examples of how a house can be protected with the system. Getting started...
Planning your Installation BLY1 Wireless Alarm System The PIRs have been separately placed in bedroom 1, bedroom 2, bedroom 3, and the area where the control panel is installed, to protect these areas. The Door/Window contact detectors have been positioned to protect the front door, back door and windows on the 1st floor.
Installing your System BLY1 Wireless Alarm System Installing the Control unit • Remove and retain the two holding screws from front cover of control unit and carefully hinge off the front cover. ST3x25KA screw Hole depth ˃22mm 5~6mm protrude surface • Place the control unit Tighten the base mounting screw to plate on the wall at fasten the the chosen location. base plate on surface Mark and drill 4mm holes for the two Base Plate mounting screws. Insert 2.
Installing your System BLY1 Wireless Alarm System Power up the Wireless Devices and learning to the CU 1. An adult must carry out battery replacement and installation. 2. Remove exhausted batteries from this product. 3. Do not dispose of batteries in a fire, batteries may explode or leak. 4. Do not short-circuit the battery terminals. 5. Do not mix used and new batteries. 6. Do not mix alkaline standard (carbon-zinc), lithium or rechargeable batteries. 7. Do not use rechargeable batteries in this product.
Installing your System BLY1 Wireless Alarm System Powering up the Wireless PIR Detector(s): Getting started... 1. Remove battery cover and insert two LR03 “AAA” size alkaline batteries incorrect polarity as shown. 2. Replace battery compartment cover. AAA 1.5V AAA 1.5V When the PIR is first powered up it will take 2 minutes for it to warm-up before it can be linked to the control unit. NOTE: After the first 2 minutes, the PIR will enter a test mode period for the next 15 minutes.
BLY1 Wireless Alarm System Installing your System Learn PIR When a PIR Detector has been learnt successfully, Z5, Z6, Z7 or Z8 zone LED depending on which next zone is unprogrammed) will flash. * The use of ear defenders is advisable at this stage* 2.3 a siren, press and release the tamper switch once located on the rear of the siren. The siren will trigger an alarm.
Installing your System BLY1 Wireless Alarm System 3. Trigger the next device within 10 seconds to learn it and repeat for additional devices. If the system has reached its maximum capacity and no more devices ca be added. The control unit will not beep any more. 4. When you have finished learning the devices, all zone LEDs will turn off after 10 seconds which indicates successful programming. After this the system returns to standby mode. Getting started...
Installing your System BLY1 Wireless Alarm System Front cover retaining screw 80.5mm b) Wireless Movement PIR Detector 1. Remove and retain the screw from the bottom of the PIR and lift off the cover. Fitting 2. If you are fitting the PIR in a corner, use mounting points “A”. If you are fitting the detector on to a flat A surface, use mounting points “B”. The mounting points are shown by indentations in the plastic B molding.
Installing your System BLY1 Wireless Alarm System Movement Detector/PIR final setup Getting started... IMPORTANT: To extend the battery life, wireless PIR detectors are designed to detect once only before entering a “Sleep” condition for two minutes during which the unit will not trigger. Any movement seen by the PIR during this period would cause “Sleep” conditions to be extended by a further two minutes.
Getting started... In more detail... Using the System 17-19 Maintenance 19 Extending the System 19 Specifications 20-21 Troubleshooting Guide 21 Disposal and Recycling 22 In more detail... Getting started... BLY1 Wireless Alarm System 16 Wireless Alarm System.
GB IE Using the System BLY1 Wireless Alarm System Control unit When the control unit is powered up, it will remain in standby mode. The PIN code can also disarm the system and put it into standby mode. a) Changing the user PIN code The User PIN code is factory set to 1234. It is highly recommended to change the user PIN code immediately after completing the basic installation. 1. Set the system into “standby mode if not already set. 2.
Using the System BLY1 Wireless Alarm System g) Part Arm the alarm system while at home Press “Part-Arm” button at the control unit or press “PARTIAL ARM” button at the remote key, (optional accessory) close the door and leave the house within the exit delay time (30 seconds at factory setting,) both PIR and magnetic contact are activated for protection after the exit delay time elapsed. When omitted zones (zone 6 to zone 8 at factory setting) are triggered, they will not activate the alarm.
Using the System/ Maintenance/ Extending the System BLY1 Wireless Alarm System Default settings Parameter Ex-factory Value User PIN code 1234 Entry/Exit delay 30 seconds Siren Duration 3 minutes In more detail... Zone allocation for PIR and MC Detectors Zone 1 to 4 Magnetic Contact Zone 5 to 8 PIRs Maintenance Once every 3 months: Test all detectors. Additionally, once every two years: It is suggested to replace all batteries in wireless detectors and the control unit.
Specifications BLY1 Wireless Alarm System Control unit Type Housing material Zones Entry/Exit Delay Siren Duration RF Receiver Frequency: Power Supply Back-up battery life Current Consumption Microprocessor based wireless control unit ABS 8 Alarm Zones–1 detector maximum per zone (8 detectors capacity) 30 seconds 3 minutes 433MHz 15V 500mA 50Hz AC/AC mains adaptor and 1 x 9V DC PP3 Alkaline for back-up power.
Specifications/ Troubleshooting BLY1 Wireless Alarm System Control Panel Power Supply Adaptor Type Housing material Rated Supply Output AC/AC Adaptor with 3-pin UK style ABS 230VAC 50HZ supply Extra Low Voltage (AC15V max at 500mA AC) Troubleshooting 1) Control unit (CU) Symptoms Power indicator and all status LEDs are off without any response Power indicator does not light up but the status LEDs or TAMPER LEDs are on. In more detail... TAMPER (Red) flashing.
BLY1 Wireless Alarm System Disposal and recycling/ Warranty Disposal and Recycling Batteries and waste electrical products should not be disposed of with household waste. Please recycle where these facilities exist. Check with your local authority or retailer for recycling advice. Declaration In more detail...
BLY1 Wireless Alarm System Appendix Appendix 24 Zone - Location Table 25 Appendix LED Alarm Indication 23 Wireless Alarm System.
Appendix B BLY1 Wireless Alarm System GB IE LED STATUS Power Tamper (GREEN) (RED) Z1/Z5 (RED) Z2/Z6 (RED) Z3/Z7 (RED) Z4/Z8 (RED) Power Ready ON X X X X X AC Failure X X X X X X Low Battery ON Flashing X X X X Z1 Alarm ON X ON X X X Z2 Alarm ON X X ON X X Z3 Alarm ON X X X ON X Z4 Alarm ON X X X X ON Z5 Alarm ON X Flashing X X X Z6 Alarm ON X X Flashing X X Z7 Alarm ON X X X Flashing X Z8 Alarm ON X X X X Flashing Z1 Tamp
Appendix B BLY1 Wireless Alarm System Zone - Location Table: Zone Number Location 1 2 3 4 5 6 7 Appendix 8 25 B&Q, Chandlers Ford, Hants, SO53 3LE United Kingdom www.diy.com Customer Helpline 0844 736 9169 Wireless Alarm System.
