Quick Reference Guide

HEX70HDU-KIT QUICK REFERENCE GUIDE
contact: [e-mail] | [e-mail]
03
EDID Control
EDID (Extended Display Identification Data) is a data structure that is used between a display and a source to negotiate
the best audio and video resolutions that are supported in the system. A global EDID of the HEX70HDU-KIT can be
configured using a combination of DIP switch settings (see below), or using IP / RS-232 commands. Please refer to the
HEX70HDU-KIT User Manual - available to download from the Blustream website.
RS-232 Configuration & Control
The RS-232 ports can be used for configuration / control of the product, as well as pass through of RS-232 commands
between the serial ports of the HEX70HDU-TX and RX. By default, the Transmitter unit is allocated for control and
feedback of switching, however this can be changed to the Receiver if required.
The default RS-232 communication settings are:
Baud rate: 57600
Data bit: 8
Stop bit: 1
Parity bit: none
For the complete RS-232 and TCP/IP command list please see the HEX70HDU-KIT User Manual - available to download
from the Blustream website.
Global EDID Settings
DIP switch position ‘0’ = O / Up
DIP switch position ‘1’ = On / Down
EDID DIP Switches
[DIP] = 0000: HDMI 1080p @60Hz, Audio 2ch PCM (default)
[DIP] = 0001: HDMI 1080p @60Hz, Audio 5.1ch PCM/DTS/DOLBY
[DIP] = 0010: HDMI 1080p @60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD
[DIP] = 0011: HDMI 1080i @60Hz, Audio 2ch PCM
[DIP] = 0100: HDMI 1080i @60Hz, Audio 5.1ch PCM/DTS/DOLBY
[DIP] = 0101: HDMI 1080i @60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD
[DIP] = 0110: HDMI 4K @60Hz 4:2:0, Audio 2ch PCM
[DIP] = 0111: HDMI 4K @60Hz 4:2:0, Audio 5.1ch PCM/DTS/DOLBY
[DIP] = 1000: HDMI 4K @60Hz 4:2:0, Audio 7.1ch PCM/DTS/DOLBY/HD
[DIP] = 1001: HDMI 4K @60Hz 4:4:4, Audio 2ch PCM
[DIP] = 1010: HDMI 4K @60Hz 4:4:4, Audio 5.1ch PCM/DTS/DOLBY
[DIP] = 1011: HDMI 4K @60Hz 4:4:4, Audio 7.1ch PCM/DTS/DOLBY/HD
[DIP] = 1100: DVI 1920x1080 @60Hz, Audio None
[DIP] = 1101: DVI 1920x1200 @60Hz, Audio None
[DIP] = 1110: EDID Passthrough
[DIP] = 1111: Soware Controlled EDID (set EDID via TCP/IP or RS-232)
Auto On / O Display Control
The HEX70HDU-KIT can be programmed to automatically power on / o a display connected to the HDBaseT™
Receiver output via CEC, RS-232 or Relay. Please refer to the HEX70HDU-KIT User Manual - available to download from
the Blustream website for more details.
Web GUI Control
The HEX70HDU-KIT features an in-built Web GUI which can be used for control and configuration of the product.
Default Username is: blustream Default Password is: 1234 Default IP Address is: 192.168.0.200
For further information please see the HEX70HDU-KIT User Manual - available to download from the Blustream
website.