Narrow Aluminum Door Installation Guide

ManualsBrandsBlum ManualsView All BlumBlum AVENTOS HK TIP-ON Lift Mechanism with Power Factor from 175 to 349

AVENTOS HK

Lift mechanism set

▀

Lift mechanism (qty 2)

▀

#7 x 35 mm (1-3/8”) wood screw (qty 10)

Power factor Opening angle Part no.

43 — 99 107°

20K2300.N5

100 — 174 107°

20K2500.N5

175 — 349 107°

20K2700.N5

350 — 792 100°

20K2900.N5

Cover set

▀ Right and left cover plate

▀ Non-handed cover cap (qty 2)

Part no.

Cover set

20K8000.NA

Narrow aluminum hardware set

▀ Arm assembly mounting plate (qty2)

▀ 669.110 — Aluminum screw for narrow aluminum lever arm

mounting plate (qty 8)

Part no.

Narrow aluminum hardware set

20S4200A

Narrow aluminum

frame door application

Summary of content (7 pages)

PAGE 1
AVENTOS HK Narrow aluminum frame door application Lift mechanism set ▀▀ Lift mechanism (qty 2) ▀▀ #7 x 35 mm (1-3/8”) wood screw (qty 10) Power factor 43 Opening angle — 99 100 — 174 Part no. 107° 20K2300.N5 107° 20K2500.N5 175 — 349 107° 20K2700.N5 350 — 792 100° 20K2900.N5 Cover set ▀▀ Right and left cover plate ▀▀ Non-handed cover cap (qty 2) Part no. 20K8000.NA Cover set Narrow aluminum hardware set ▀▀ Arm assembly mounting plate (qty2) ▀▀ 669.
PAGE 2
Assembly WARNING Risk of injury from spring-loaded arm ▀▀ Do not push arm assembly down or leave in the down position ▀▀ Remove mechanism before installing or removing cabinet Locating pin locations and minimum depth 77 1 5 128 37 261 Part no. Universal individual template is available for pre-boring 5 mm locating pins 2 65.1051.02 Attaching the lift mechanism Align the lift mechanism in the cabinet using the 5 mm locator pins and attach the mechanism with the three wood screws provided.
PAGE 3
Remove transport tab from lift mechanism and raise arms A B Raise the arm to the upright position. Carefully remove the transport tab. Risk of injury from spring loaded arm. NOTE: Do not remove transport tab until just before attaching the door 4a 4b Mounting plate position Planning narrow alum. frames Attach the mounting plate to the door. 15 to 19 NOTE: When changing material thickness, adjust assembly dimensions. 11.4 19 to reveal (1 to 4) ov erl overlay 21 ay -4 .5 38 90° Ø7– 0.
PAGE 4
Assembly 5 Attaching the door Attach the door using the CLIP mechanism in the mounting plate. 6 Adjust the door tension Use a screw gun and the supplied #2 x 2 POZI driver bit to adjust the lift mechanism to the desired tension. 4 Subject to technical modifications without notice.
PAGE 5
7 Finalize the door adjustments 1 3 mm 2 mm 3 mm 2 1 Use a POZI screwdriver to adjust cam adjustments for each of the three-dimensional adjustments. 8 Attach cover caps Snap the symmetrical cover caps on each cover plate. Place the left and right cover plates over the appropriate lift mechanisms and snap them in place. Subject to technical modifications without notice.
PAGE 6
Removal WARNING Risk of injury from spring-loaded arm ▀▀ Do not push arm assembly down or leave in the down position ▀▀ Remove mechanism before installing or removing cabinet 1 Removing the covers Remove the cover caps and cover plate. 2 ▀▀ ▀▀ 6 Removing the door Open the door. Use a screwdriver to disengage the CLIP mechanism of the lever arm from the mounting plate Support the door with one hand and repeat on the other side Subject to technical modifications without notice.
PAGE 7
Other information Inch Panel door clearance X / .031 1 /16 .063 1.5 3 32 / .094 2 18 / .125 3 5 32 / .156 4 3 16 / .188 5 7 32 / .219 5.5 14 / .25 6 9 32 / .281 7 / .313 8 1 door thickness Door thickness 16 19 22 26 5 16 X 70 59 49 35 11 Blum, Inc. 800-438-6788 sales.us@blum.com blum.com Subject to technical modifications without notice. © 2015 INST-AVT09-04.15 mm 1 32 /32 .344 9 3 8 / .375 9.5 13 32 / .406 10 7 16 / .