Online UPS EN PowerWalker VFI 10000CP PowerWalker VFI 15000CP PowerWalker VFI 20000CP PowerWalker VFI 30000CP 3/3 3/3 3/3 3/3 PowerWalker VFI 10000CP PowerWalker VFI 15000CP PowerWalker VFI 20000CP PowerWalker VFI 30000CP Manual 3/3L 3/3L 3/3L 3/3L EN+ES+IT Uninterruptible Power Supply System
EN Please comply with all warnings and operating instructions in this manual strictly. Save this manual properly and read carefully the following instructions before installing the unit. Do not operate this unit before reading through all safety information and operating instructions carefully.
Table of Contents 1. SAFETY AND EMC INSTRUCTIONS ................................................................................................. 1 1-1. TRANSPORTATION AND STORAGE ...............................................................................................................1 1-2. PREPARATION.......................................................................................................................................1 1-3. INSTALLATION ...............................................
1. Safety and EMC instructions EN Please read carefully the following user manual and the safety instructions before installing the unit or using the unit! 1-1. Transportation and Storage Please transport the UPS system only in the original package to protect against shock and impact. The UPS must be stored in the room where it is ventilated and dry. 1-2. Preparation Condensation may occur if the UPS system is moved directly from cold to warm environment.
1-4. Operation Do not disconnect the earth conductor cable on the UPS or the building wiring terminals in any time since this would cancel the protective earth of the UPS system and of all connected loads. The UPS system features its own, internal current source (batteries). The UPS output sockets or output terminal blocks may be electrically live even if the UPS system is not connected to the building wiring outlet.
2. Installation and Operation EN There are two different types of online UPS: standard and long-run models. Please refer to the following model table. Model Type Model Type 10000 10000L 15000 15000L Standard Long-run model model 20000 20000L 30000 30000L We also offer optional parallel function for these two types by request. The UPS with parallel function is called as “Parallel model”. We have described detailed installation and operation of Parallel Model in the following chapter. 2-1.
2-2.
1. RS-232 communication port 2. USB communication port 3. Emergency power off function connector (EPO connector) 4. Share current port (only available for parallel model) 5. Parallel port (only available for parallel model) EN 6. Intelligent slot 7. Power stage fan 8. External battery terminal 9. Bypass Input Circuit Breaker(Only available for dual input unit) 10. Input/Output terminal (Refer to Diagram 2) 11. Line Input circuit breaker 12. Maintenance bypass switch 13. Output Grounding terminal 14.
NOTE 1: The cable for 10000/10000L should be able to withstand over 40A current. It is recommended to use AWG 10 or thicker wire for Phase and AWG 8 or thicker wire for Neutral for safety and efficiency. NOTE 2: The cable for 15000/15000L should be able to withstand over 63A current. It is recommended to use AWG 8 or thicker wire for Phase and AWG 6 or thicker wire for Neutral for safety and efficiency. NOTE 3: The cable for 20000/20000L should be able to withstand over 63A current.
For dual input unit, if there is two separate input, connect the Line input and bypass input respectively; if the is only one common input, please connect the line input and bypass input together. NOTE 1: Make sure that the wires are connected tightly with the terminals. EN NOTE 2: Please install the output breaker between the output terminal and the load, and the breaker should be qualified with leakage current protective function if necessary.
2-4. UPS Installation for Parallel System If the UPS is only available for single operation, you may skip this section to the next. 1) Install and wires the UPSs according to the section 2-3. 2) Connect the output wires of each UPS to an output breaker. 3) Connect all output breakers to a major output breaker. Then this major output breaker will directly connect to the loads. 4) Each UPS is connected to an independent battery pack. NOTE: The parallel system can not use one battery pack.
EN Wiring diagram of parallel system for 30000(L) 2-5. Software Installation For optimal computer system protection, install UPS monitoring software to fully configure UPS shutdown.
3. Operations 3-1. Button Operation Button EN Function ON/Enter Button Turn on the UPS: Press and hold the button more than 0.5s to turn on the UPS. Enter Key: Press this button to confirm the selection in setting menu. OFF/ESC Button Turn off the UPS: Press and hold the button more than 0.5s to turn off the UPS. Esc key: Press this button to return to last menu in setting menu. Test/Up Button Mute/Down Button Test/Up + Mute/Down Button Battery test: Press and hold the button more than 0.
LCD Panel: EN Display Function Backup time information Indicates the battery discharge time in numbers H: hours, M: minutes, S: seconds Fault information Indicates that the warning and fault occurs. Indicates the fault codes, and the codes are listed in details in section 3-9. Mute operation Indicates that the UPS alarm is disabled. Output & Battery voltage information Indicates the output voltage, frequency or battery voltage.
Battery information Indicates the Battery capacity by 0-25%, 26-50%, 51-75%, and 76-100%. EN Indicates the battery is not connected. Indicates low battery level and low battery voltage. Input & Battery voltage information Indicates the input voltage or frequency or battery voltage. Vac: Input voltage, Vdc: battery voltage, Hz: input frequency 3-3.
3. Connect devices to UPS After the UPS is turned on, you can connect devices to the UPS. 1) EN Turn on the UPS first and then switch on the devices one by one, the LCD panel will display total load level. 2) If it is necessary to connect the inductive loads such as a printer, the in-rush current should be calculated carefully to see if it meets the capacity of the UPS, because the power consumption of this kind of loads is too big. 3) If the UPS is overload, the buzzer will beep twice every second.
NOTE 2: After turning off the UPS, please be aware that the UPS is working at Bypass mode and there is risk of power loss for connected devices. 2) In Bypass mode, output voltage of the UPS is still present. In order to cut off the output, switch off the line input breaker(for dual input unit, also switch off the bypass line breaker). A few seconds later, there is no display shown on the display panel and UPS is complete off. 8.
6) Switch on the line input breaker(for dual input unit, also switch on the bypass input breaker) and the UPS will enter Bypass mode. If the UPS is in maintenance Bypass mode, turn the maintenance switch to “UPS” position and then turn on the UPS. 3-5. Parallel Operation 1. Parallel system initial startup EN First of all, please make sure all of the UPSs are parallel models and have the same configuration. 1) Turn on each UPS to AC mode respectively (Refer to section 3-4(1)).
1) Press the “OFF” key twice and each time should be lasted for more than 0.5s. Then, the UPS will enter into bypass mode or no output mode without output. 2) Turn off the output breaker of this unit, and then turn off the input breaker of this unit. 3) After it shuts down, you can turn off the battery breaker (for long-run model) and remove the parallel and share current cables. And then remove the unit from the parallel system.
EN OP.V Output voltage PAR Parallel, 001 means the first UPS AN The first phase BN The second phase CN The third phase AB The first line BC The second line CA The third line 3-7. LCD Setting There are three parameters to set up the UPS. Refer to following diagram. Parameter 1: It’s for program alternatives. Refer to below tables for the programs to set up. Parameter 1 Parameter 2 and parameter 3 are the setting options or values for each program.
13 Battery voltage calibration Y Y Y Y Y Y 14 Charger voltage adjustment Y Y Y Y Y Y 15 Inverter A voltage adjustment Y Y Y 16 Inverter B voltage adjustment Y Y Y 17 Inverter C voltage adjustment Y Y Y 18 Output A voltage calibration Y Y Y 19 Output B voltage calibration Y Y Y 20 Output C voltage calibration Y Y Y *Y means that this program can be set in this mode.
03: Voltage range for bypass Interface Setting Parameter 2: Set the acceptable low voltage for bypass. Setting range is from 110V to 209V and the default value is 110V. Parameter 3: Set the acceptable high voltage for bypass. Setting range is from 231V to 276V and the default value is 264V. EN 04: Frequency range for bypass Interface Setting Parameter 2: Set the acceptable low frequency for bypass. 50 Hz system: Setting range is from 46.0Hz to 49.0Hz. 60 Hz system: Setting range is from 56.0Hz to 59.
Parameter 2: OPN: Bypass allowed. When selected, UPS will run at Bypass mode depending on bypass enabled/disabled setting. FBD: Bypass not allowed. When selected, it’s not allowed for running in Bypass mode under any situations. Parameter 3: ENA: Bypass enabled. When selected, Bypass mode is activated. DIS: Bypass disabled. When selected, automatic bypass is acceptable, but manual bypass is not allowed. Manual bypass means users manually operate UPS for Bypass mode.
CHE: The UPS will automatically detect the neutral loss. If neutral loss is detected, an alarm will be generated. If the UPS is turned on, it will transfer to battery mode. When neutral is restored, the alarm will NOT be muted automatically and the UPS will NOT go back to normal mode automatically. Here, you must mute the alarm and make the UPS go back to normal mode manually. The operation is: Firstly, enter this menu and press the “Enter” key to make the “CHE” flash.
17: Inverter C voltage adjustment Interface Setting Parameter 2: you may choose Add or Sub to adjust inverter C voltage*. Parameter 3: the voltage range is from 0V to 9.9V, the default value is 0V. *It will display number 2 under inverter C voltage. Setting Parameter 2: it always shows OP.V as output voltage. Parameter 3: it shows the internal measurement value of the output A voltage, and you can calibrate it by pressing Up or Down according to the measurement from an external voltage meter.
3-8. Operating Mode/Status Description EN Following table shows LCD display for operating modes and status. (1) If the UPS is in normal operation, it will show seven screens one by one, which represents 3 phase input voltages (An, bn, Cn), 3 line input voltages (Ab, bC, CA) and frequency in turns. (2) If parallel UPS systems are successfully set up, it will show one more screen with “PAR” in parameter 2 and assigned number in parameter 3 as below parallel screen diagram.
EN AC mode Description When the input voltage is within acceptable range, UPS will provide pure and stable AC power to output. The UPS will also charge the battery at AC mode. LCD display ECO mode Description When the input voltage is within voltage regulation range and ECO mode is enabled, UPS will bypass voltage to output for energy saving.
EN CVCF mode Description When the output frequency is set to “CF”, the inverter will output constant frequency (50 Hz or 60 Hz). At this mode, the UPS will have no bypass output but still charge battery.
Battery mode Description When the input voltage/frequency is beyond the acceptable range or power failure, UPS will backup power from battery and alarm will beep every 4 seconds. LCD display EN Bypass mode Description When input voltage is within acceptable range and bypass is enabled, turn off the UPS and it will enter Bypass mode. Alarm beeps every two minutes.
EN Battery Test Description When UPS is in AC mode or CVCF mode, press “Test” key for more than 0.5s. Then, the UPS will beep once and start “Battery Test”. The line between I/P and inverter icons will blink to remind users. This operation is used to check the battery status. LCD display Warning Description status If some errors occur in the UPS (but it is still running normally), it will show one more screen to represent the warning situation.
Fault status Description When UPS has fault happened, the inverter will be blocked. It will display fault code in screen, and the icon will light up. You can find the code meaning in the fault code table.
3-9.
3-11.
Other fault codes are shown on LCD display and alarm beeps continuously. EN Battery backup time is shorter than nominal value A UPS internal occurred. fault has Batteries are not fully charged Batteries defect The icon and flash on LCD display and alarm beeps every second. Symptom The warning code 02 is shown, the icon flashes on LCD display, and alarm beeps every second. Fan is locked or not working; or the UPS temperature is too high. Possible cause The input neutral wire disconnected.
5. Storage and Maintenance 5-1. Storage Before storing, charge the UPS at least 7 hours. Store the UPS covered and upright in a cool, dry location. During storage, recharge the battery in accordance with the following table: Storage Temperature Recharge Frequency Charging Duration -25°C - 40°C Every 3 months 1-2 hours 40°C - 45°C Every 2 months 1-2 hours 5-2. Maintenance The UPS system operates with hazardous voltages. Repairs may be carried out only by qualified maintenance personnel.
6. Specifications MODEL CAPACITY* INPUT 10000 10000L 10000VA / 9000W 15000 15000L 15000VA / 13500W Voltage Range 30000 30000L 30000VA / 27000W 110 VAC(Ph-N) ± 3 % at 50% Load 176 VAC(Ph-N) ± 3 % at 100% Load Low Line Loss Voltage + 10V 300 VAC(L-N) ± 3 % at 50% Load 276 VAC(L-N) ± 3 % at 100% Load High Line Loss Voltage - 10V 46Hz ~ 54 Hz @ 50Hz system 56Hz ~ 64 Hz @ 60Hz system Three phase with Neutral ≧ 0.
Online UPS ES PowerWalker VFI 10000CP PowerWalker VFI 15000CP PowerWalker VFI 20000CP PowerWalker VFI 30000CP 3/3 3/3 3/3 3/3 PowerWalker VFI 10000CP PowerWalker VFI 15000CP PowerWalker VFI 20000CP PowerWalker VFI 30000CP 3/3L 3/3L 3/3L 3/3L Manual EN+ES+IT Sistema de Alimentación Ininterrumpida
ES Siga estrictamente todas las advertencias e instrucciones en este manual. Guarde este manual antes de instalar las unidades de SAI para leer todas las instrucciones atentamente. No utilice el SAI antes de leer atentamente toda la información de seguridad y las instrucciones de uso.
TABLA DE CONTENIDOS 1. INSTRUCCIONES DE SEGURIDAD Y DE COMPATIBILIDAD ELECTROMAGNÉTICA (EMC) ............. 1 1-1. TRANSPORTE Y ALMACENAMIENTO .............................................................................................................1 1-2. PREPARACIÓN ......................................................................................................................................1 1-3. INSTALACIÓN ........................................................................................
1. Instrucciones de seguridad y de compatibilidad electromagnética (EMC) ES Por favor, lea el siguiente manual del usuario y las instrucciones de seguridad antes de instalar o utilizar su SAI! 1-1. Transporte y Almacenamiento Por favor, sólo llevan el SAI en su embalaje original para protegerlo de los choques y los impactos. El SAI se debe mantenerse en ambiente seco y ventilado. 1-2. Preparación Si el SAI se ha movido de un lugar frío a caliente se puede producir condensación.
Cuando se ejecuta el cableado del sistema SAI, en primer lugar, conectar la masa de tierra a los terminales. La instalación y el cableado del sistema SAI deben ser ejecutados de conformidad con las leyes y reglamentos eléctricos. 1-4. Intervención En cualquier momento y por cualquier razón, nunca desconecte el cable de tierra de las masas, en SAI o a los terminales de cableado, porque anula la protección de todo el sistema, incluyendo todas las cargas conectadas al SAI.
2. Instalación y Operación Existen dos tipos de SAI on-line: modelo estándar y una larga autonomía. Por favor refiérase a la modelo en la siguiente tabla. ES Model 1000 1500 2000 3000 Type Model 1000L 1500L 2000L 3000L Standard model Type Long-run model Opcional en ambos modelos, puede solicitar la función de forma paralela. La instalación y el modelo de SAI en paralelo, se describe en detalle en el capítulo siguiente. 2-1.
2-2.
ES 13 14 15 17 Figura 4: 3000(L) Terminali de entrada y salida 1. RS-232: puerto de comunicación 2. Puerto de comunicación USB 3. Emergencia: apagar la función del conector la EPO 4. Parte del puerto de corriente (disponible sólo para el modelo paralelo) 5. Puerto paralelo (disponible sólo para el modelo paralelo) 6. Inteligente Slot 7. Ventiladores 8. Conector bateria externa 9. Interruptor de entrada 10. Terminales de entrada y salida (Referencia figura 2) 11. Interruptor de entrada 12.
Modelo Especifica cable de conexión (AWG) Entrada(Ph) Entrada(Ph) Entrada(Ph) 8 1000 10 10 8 1000L 10 10 8 1500 8 8 6 1500L 8 8 6 2000 8 8 6 2000L 8 8 6 3000 8 8 4 3000L 8 8 4 8 8 6 6 6 6 6 6 4 4 4 NOTA 1: El cable para 10000/10000L debe ser capaz de soportar más de corriente 40A. Se recomienda el uso de hilo de 10 AWG o más grueso de alambre para la fase y el GTE-8 o más grueso alambre para neutro para la seguridad y la eficiencia.
ES Figura de las conexiones por 30000(L) Por dos unidades de entrada, si hay dos entradas separadas, conecte la entrada de línea y entrada de la derivación, si es sólo una entrada común, conecte la entrada de línea y entrada de derivación. NOTA 1: Verifique que los cables estén bien conectados a cada pin del terminal.
2-4. Instalación del sistema SAI en paralelo Si el SAI debe ser utilizado en singla unidad, no tener cuenta de esta sección para la conexión paralela. 1) Instale el SAI y el cable teniendo en cuenta la sección 2-3. 2) Conecte el cable de salida de cada SAI a un interruptor de salida. 3) Conecte todos los interruptores en un solo interruptor, de potencia nominal de todos los SAI en paralelo. Luego de esta importante salida de interruptor se conecta directamente a las cargas.
sistema del SAI en su totalidad. 3. Operaciones 3-1. Pulsante de funcionamiento ES Pulsante Función ON/Enter Botón Activa el SAI: Pulse el botón más de 0.5s para encender el SAI. Enter Key: Pulse para confirmar la selección en el menú de configuración. OFF/ESC Botón Desactiva el SAI: Presione el botón más de 0.5s para apagar el SAI. Presione este botón para volver al último menú de configuración.
Pannello LCD: ES Display Funzione Informazioni del tempo di autonomia Indica il tempo di autonomia con orologio analogico. Indica il tempo d’autonomia con orologio digitale. H: ore, M: minuti, S: secondi Informazioni del guasto Indica che l'allarme e di guasto. Indica il codice del guasto, elencati in dettaglio nella sezione 3-9. Funzionamento senza allarmi Indica che l’allarme sonoro è disabilitato. Informazione uscita e batteria Indica la tensione d’uscita, frequenza, o tensione batteria.
Indica che il modo ECO è attivo. Indica che il circuito inverter è attivo. Indica le prese d’uscita sono attive. Informazioni batteria ES Indica il livello della batteria, da: 0-25%, 26-50%, 51-75%, e 76-100%. Indica un guasto alla batteria. Indica la bassa tensione della batteria. Informazione tensione d’ingresso e Batteria Indica la tensione d’ingresso, o frequenza, o tensione della batteria. Vac = tensione ingresso, Vdc = Volt batteria, Hz = frequenza d’entrata 3-3.
1) Asegúrese de que el interruptor de la batería esté en posición "ON" (para el modelo con batería de larga autonomía). 2) Presione el botón "ON" por 0.5s para activar el SAI y la alarma suena una vez. 3) Después de algunos segundos, el SAI se encenderá en el modo de batería. 3. Conectar los dispositivos en SAI. Después de la SAI está activada, se puede conectar dispositivos al SAI. 1) Encienda el SAI y en la pantalla LCD controlar el nivel de carga total.
1) Para comprobar el estado de la batería cuando el SAI está operando en un modo red CA CVCF / ECO modo, pulsar el botón "Test" el SAI puede ejecutar auto-test de batería. 2) Para mantener el sistema fiable, el SAI automáticamente realizar auto-test periódicamente. El período por predefinido es una vez por semana. 3) Los usuarios pueden configurar su auto-test bateria a través del software.
2) Apague el SAI. Si la carga no se puede ser excluida, debe quitar la tapa de mantenimiento de bypass, en la parte trasera y gire el desviador de SAI a BPS. 3) Apague el interruptor de entrada, y apagar el interruptor de la batería (sólo para el modelo de larga duración de la batería). 4) Retire la tapa de la SAI y desconectar la batería para el modelo estándar. A continuación, cambie el puente JS3 en la placa de control para ajustar el número de la batería como se muestra en la siguiente tabla.
c) Encienda cada SAI uno a tras otro. En poco tiempo los SAI entran en modo CA síncrono y el sistema paralelo se ha completado. 6) Encender el sistema de forma paralela en modo bateria: a) Conectar el interruptor de la batería (sólo para SAI a larga autonomía) y interruptor de salida de cada SAI. ES NOTA: No se le permite compartir una batería de SAI de larga autonomía en paralelo. Cada SAI debe ser conectado a su batería. b) Encienda un SAI, después de unos segundos, entra en modo batería.
3-6. Significado de las abreviaciones in display LCD Abreviación Contenido en display Significado ENA Activado DIS Deshabilitado ATO Automático BAT Bateria NCF Modo normal modo (no por modo CVCF) CF Modo CVCF SUB Sacar ADD Adicional ON On OFF Off FBD No consentido OPN Permiso RES Reservado N.L Perdida de la línea neutral CHE Controlo OP.
Parámetro 1: Es por programa alternativo. Tiene 15 programas de instituir. Hacer referencia a la tabla reportada en seguida. Parametro 1 Parámetro 2 y 3 son los parámetros de opciones de impostación o valores por cada programa.
01: Voltaje de salida Interface 02:Voltaje entrada Interface 60 Hz, CVCF modo Impostación Parámetro 3: tensión de salida Es posible elegir las siguientes salidas de tensión en parámetro 3: 208 indica tensión de salida = 208Vac 220: indica tensión de salida = 220Vac 230: indica tensión de salida = 230Vac 240: indica tensión de salida = 240Vac Impostación Parámetro 2: frecuencia salida Ajuste de la frecuencia de salida. Puede elegir tres opciones en el parámetro 2: 50.
50 Hz: Campo de regulación de 54,0 Hz Hasta 51.0Hz. 60 Hz: Campo de regulación es de 61.0Hz hasta 64.0Hz. El valor predefinido es 54.0Hz/64.0Hz. ES 05: Modo ECO activar o desactivar Interface Impostación Parámetro 3: Activar o desactivar la función ECO.
Parámetro 3: 000 ~ 999: Establece el tiempo máximo de autonomía: de 0 minutos a 999 minutos. El SAI se apagará para proteger a la batería, lo que viene después de la hora fijada. El valor por defecto es 990 minutos. DIS: Deshabilitar la descarga de la batería: la protección de la autonomía y el tiempo dependerá de la capacidad de la batería. 10: Reservado Interface 11: Reservado Interface ES Impostación Reservado por futuro. Impostación Reservado por futuro.
13: Regulaciones de tensión de la bateria Interface Impostación Parámetro 2: Seleccionar "Add" o "Sub" la función de la regulación de tensión bateria de vera y propia configuración. Parámetro 3: la gama de tensión es de 0V hasta 9.9V, el valore predefinido es 0V. ES 14: Regulación del carga bateria Interface Impostación Parámetro 2: se puede elegir Add o Sub por regular la tensión de la carga bateria. Parámetro 3: la gama de tensión es de 0V hasta 9.9V, el valor predefinido es 0V.
Parámetro 2: se muestra siempre como OP.V tensión de salida. Parámetro 3: muestra el valor interior de medida de la tensión de salida A, y puede ser calibrado pulsando Arriba (Up) u Abajo (Down) de acuerdo con el valor de medida de un voltaje externo. El resultado de la calibración es eficaz pulsando Enter. El rango de calibración está limitada a + /- 9V. Esta función se utiliza normalmente para el funcionamiento en paralelo.
3-8. Modo operativo / Descripción de estado. ES La siguiente tabla mostra el display LCD por el modo de funcionamiento y de estado. (1) Si el SAI es en funcionamiento normal, mostrará siete esquemas uno por uno, que representa 3 tensiones de entrada de fases (An, bn, Cn), 3 tensiones de entrada de línea (Ab, bC, CA) y la frecuencia en rotación.
ES Modo CA Descripción Cuando el voltaje de entrada está en el parámetro de acción aceptable, el SAI proporciona una salida de energía CA limpia y estable. El SAI también carga la batería en modo CA. LCD display Modo ECO Descripción Cuando la tensión de entrada está en el intervalo de regulación de tensión y el modo ECO está activado, el SAI bypass la tensión de salida para el ahorro de energía.
ES Modo CVCF Descripción Cuando la frecuencia de salida se pone a "CF", el inversor emite una frecuencia constante (50 Hz o 60 Hz). De este modo, el SAI no tiene la salida me todavía cargar la batería. LCD display Modo bateria Descripción Cuando la tensión de entrada / frecuencia no está en los valores aceptables o corte de energía, el SAI funciona con batería y emite una alarma audible cada 4 segundos.
LCD display ES Modo Bypass Descripción Cuando el voltaje de entrada se encuentra dentro de las tolerancias aceptables y bypass activado, se apaga el SAI y entra en modo Bypass. Emitiendo una alarma audible cada dos minutos.
ES Test bateria Descripción Cuando el SAI está en modo AC o CVCF, pulse el botón "Test" durante más de 0,5 s. Entonces, el SAI suena y comienza la "Prueba de la batería". La línea divisoria entre la I / P y el inversor iconos parpadea para recordar a los usuarios. Esta operación se utiliza para comprobar el estado de la batería.
estado código de error en la pantalla y el icono se iluminará. Usted puede encontrar el significado del código de la tabla de códigos de error. LCD display ES 3-9.
3-10. Indicadores de advertencia Advertencia ES Icono (flashing) Alarmas Bateria baja Sonido cada segundo Sobrecarga Tres sonido cada segundo Bateria desequilibrado Sonido cada segundo Carga alta Sonido cada segundo Habilitaciones de EPO Sonido cada segundo Guasto ventiladora guasto/alta Sonido cada segundo temperatura. Guasto en el carga bateria Sonido cada segundo Interacción fusibles I/P Sonido cada segundo 3-11.
4. Resolución de problemas Si el SAI no funciona correctamente, por favor solucionar los problemas utilizando la tabla abajo indicada. Síntoma Posibles causas Remedio Ninguna indicación de alarma misma si alimentación es normal. La línea AC di no es bien conectada a la red principal de potencia. Controlar si el cable de alimentación de entrada es conectado a la red. El icono y el código indican con LCD display parpadeante y sonido de alarma cada segundo. EPO es in posición activa.
causa interna del SAI. ES El tiempo de autonomía es más inferior del valor nominal. La bateria no es completamente cargada. Contactar el servicio asistencia, por sustituir la bateria. Bateria defectuosa. El icono y parpadeante en LCD display, con aviso acústico cada segundo. El código de alarma 02 se muestra, el icono aparece en display LCD y la alarma suena cada segundo. Los cables son invertidos con la línea neutra.
5. Almacenamiento y mantenimiento 5-1. Conservación Si es posible y para ser seguro, antes de almacenamiento cargar la batería para 5 horas. Mantenga el SAI en posición vertical, en un lugar, seco y fresco. Durante el almacenamiento "stock", recargar la batería como indicada en el cuadro siguiente Temperatura de stock Frecuencia de recarga Duración de la carga -25°C - 40°C Cada 3 mes 1-2 ore 40°C - 45°C Cada 2 mes 1-2 ore 5-2. Manutención El SAI funciona con voltajes peligrosos.
6. Specifiche MODELO CAPACIDAD* ENTRADA 1000 1000L 10000VA / 9000W Gama Volt 2000 2000L 20000VA / 18000W 3000 3000L 30000VA / 27000W 110 VAC(Ph-N) ± 3 % at 50% carico 176 VAC(Ph-N) ± 3 % at 100% carico Línea con tensione baja + 10V 300 VAC(Ph-N) ± 3 % at 50% carico 276 VAC(Ph-N) ± 3 % at 100% carico Línea con tensión alta - 10V Sistema = 46Hz ~ 54 Hz @ 50Hz Sistema = 56Hz ~ 64 Hz @ 60Hz Trifasica + neutro ≧ 0.
Online UPS IT PowerWalker VFI 10000CP PowerWalker VFI 15000CP PowerWalker VFI 20000CP PowerWalker VFI 30000CP 3/3 3/3 3/3 3/3 PowerWalker VFI 10000CP PowerWalker VFI 15000CP PowerWalker VFI 20000CP PowerWalker VFI 30000CP 3/3L 3/3L 3/3L 3/3L Manuale EN+ES+IT Uninterruptible Power Supply System
IT Si prega di rispettare strettamente tutte le avvertenze e le istruzioni d'uso in questo manuale. Conservare con cura questo manuale, perché prima d’istallare le unità (UPS) è necessario leggere attentamente tutte le istruzioni. Prima di utilizzare l’UPS, è necessario leggere con molta attenzione tutte le informazioni sulla sicurezza e istruzioni per l'uso.
Indice 1. ISTRUZIONI SULLA SICUREZZA E COMPATIBILITÀ ELETTROMAGNETICA (EMC) ................................. 1 IT 1-1. TRASPORTO E STOCCAGGIO........................................................................................................................... 1 1-2. PREPARAZIONE.............................................................................................................................................. 1 1-3. ISTALLAZIONE ..............................................................
1. Istruzioni sulla sicurezza e compatibilità elettromagnetica (EMC) Si prega di leggere attentamente il seguente manuale dell'utente e le istruzioni di sicurezza prima di installare o utilizzare l'unità UPS! IT 1-1. Trasporto e Stoccaggio Si prega di trasportare l'UPS solamente nella confezione originale per proteggerlo dagli urti e impatti. L'UPS deve essere conservato in ambiente ventilato e asciutto. 1-2. Preparazione Se l'UPS è spostato da un ambiente freddo al caldo, può verificarsi condensa.
1-4. Interventi In qualsiasi momento e per qualsiasi ragione, mai scollegare il cavo della massa terra, sull'UPS o dai terminali del cablaggio, perché annulla la protezione di tutto il sistema, compreso tutti i carichi collegati all’UPS. L'UPS ha le proprie caratteristiche, con sorgenti elettriche interne (es. batterie). Le prese o terminali in uscita dell'UPS possono avere correnti elettriche, anche se l'UPS non è collegato alla rete.
2. Installazione e funzionamento Ci sono due tipi di UPS online: modelli standard e di lunga autonomia. Consultare la tabella seguente per il modello. IT Model 1000 1500 2000 3000 Type Model 1000L 1500L 2000L 3000L Standard model Type Long-run model Opzionale ai due modelli, è possibile richiedere la funzione di parallelo. L'installazione e il funzionamento dell'UPS modello in parallelo, è descritta in dettagliato nel capitolo seguente. 2-1.
2-2.
IT 13 14 15 17 Figura 4: 30000(L) Input/Output Terminali 1. RS-232 porta di comunicazione 2. USB porta di comunicazione 3. Emergenza: spegnere la funzione del connettore EPO 4. Parte porta di corrente (disponibile solo per modello parallelo) 5. Porta di parallelo (solo per modello parallelo) 6. Slot intelligente 7. Ventilatori 8. Connettore batterie esterne 9. Interruttore ingresso (disponibile solo per unità a doppio ingresso) 10. Terminali d’entrata e uscita (Referenza figura 2) 11.
Modello Specifica dei cavi (AWG) Entrata(Ph) Entrata(Ph) Entrata(Ph) 8 1000 10 10 8 1000L 10 10 8 1500 8 8 6 1500L 8 8 6 200 8 8 6 2000L 8 8 6 3000 8 8 4 3000L 8 8 4 8 8 6 6 6 6 6 6 4 4 4 NOTA 1: Il cavo per 10000/10000L deve sopportare corrente oltre 40A. Si raccomanda d'utilizzare il tipo 8AWG o cavo efficiente di sicurezza. NOTA 2: Il cavo per 15000/15000L deve sopportare corrente oltre 63A.
IT Figura delle connessioni per 30000(L) Per due unità d’ingresso, se ci sono due entrate separate, collegare l'ingresso di linea ed entrata di bypass; se è solo un ingresso comune, collegare l'entrata di linea e ingresso di bypass. NOTE 1: Controllare che i cavi sono ben collegati ai singoli poli del terminale.
parallelo. 1) Installare l'UPS e cavi considerando la sezione 2-3. 2) Collegare il cavo d'uscita di ciascun UPS a un interruttore d'uscita. 3) Collegare tutti gli interruttori d'uscita a un unico, della potenza nominale degli UPS in parallelo. Poi questa importante uscita dell'interruttore si collega direttamente ai carichi. 4) Ogni UPS è collegato a una batteria indipendente. NOTA: Una sola batteria ricaricabile, non può essere utilizzata dagli UPS in parallelo.
3. Operazioni 3-1. Pulsante di funzionamento Pulsante IT Funzione ON/Enter Button Accende l'UPS: premere il tasto per più di 0.5s per accendere l'UPS. Enter Key: premere questo tasto, per confermare la selezione del menu. OFF/ESC Button Spegne l'UPS: premere il pulsante per più 0.5s per spegnere l'UPS. Premere questo pulsante per tornare all'ultimo menu d'impostazione. Test/Up Button Mute/Down Button Test/Up + Mute/Down Button Battery test: premere il pulsante per più di 0.
Pannello LCD: IT Display Funzione Informazioni del tempo di autonomia Indica il tempo di autonomia con orologio analogico. Indica il tempo d’autonomia con orologio digitale. H: ore, M: minuti, S: secondi Informazioni del guasto Indica che l'allarme e di guasto. Indica il codice del guasto, elencati in dettaglio nella sezione 3-9. Funzionamento senza allarmi Indica che l’allarme sonoro è disabilitato. Informazione uscita e batteria Indica la tensione d’uscita, frequenza, o tensione batteria.
Indica che il modo ECO è attivo. Indica che il circuito inverter è attivo. Indica le prese d’uscita sono attive. Informazioni batteria IT Indica il livello della batteria, da: 0-25%, 26-50%, 51-75%, e 76-100%. Indica un guasto alla batteria. Indica la bassa tensione della batteria. Informazione tensione d’ingresso e Batteria Indica la tensione d’ingresso, o frequenza, o tensione della batteria. Vac = tensione ingresso, Vdc = Volt batteria, Hz = frequenza d’entrata 3-3. .
2. Accendere l'UPS in modo batteria 1) Assicurarsi che l'interruttore della batteria è in posizione "ON" (solo per il modello a lunga autonomia.) 2) Premere il pulsante "ON" per 0.5s per attivare l'UPS, il cicalino emette un segnale acustico una volta. 3) Dopo pochi secondi l'UPS sarà attivato in modo batteria. 3. Collegare i dispositivi all’UPS Dopo che l'UPS è acceso, è possibile collegare i dispositivi all'UPS. 1) Accendere l'UPS e sul display LCD visualizzare il livello di carico totale.
7. Spegnere l'UPS in funzionamento modo rete AC 1) Per spegnere l'inverter dell'UPS premere il pulsante "OFF", per almeno 0.5s, il cicalino emette un segnale acustico una volta. L'UPS si trasformerà in modo bypass. NOTA 1: Se l'UPS è stato impostato per consentire alle prese d'uscita di funzionare in bypass, tutti i terminali saranno nello stesso modo (bypass).
JS3 Numero batterie in serie pin1 & pin2 pin3 & pin4 Pin5 & pin6 pin7 & pin8 18 1 0 0 X 19 0 1 0 X 20 0 0 1 X Nota: 1 = collegare con il ponticello; 0 = nessun ponticello; x = i pin sono per altre funzioni. 5) Modificare la batteria per l'impostazione numero con cautela. Dopo completamento, rimettere il coperchio, accendere l'interruttore automatico per batteria modello a lunga autonomia.
NOTA: Non è permesso di condividere una batteria per UPS a lunga autonomia in parallelo. Ogni UPS deve essere collegato alla sua batteria. b) Accendere un UPS, dopo pochi secondi, entrerà in modo batteria c) Accendere l’altro UPS, dopo pochi secondi e aggiungendosi al sistema parallelo. d) Se dovete aggiungere un terzo UPS, seguire la stessa procedura di c) e il sistema parallelo è completato.
3-6. Significato delle abbreviazioni in display LCD Abbreviazioni Commento nel Display Significato ENA Abilitato DIS Disabilitato ATO Automatico BAT Batteria NCF Modo normale mode (non per modo CVCF) CF Modo CVCF SUB Togliere ADD Addizionale ON On OFF Off FBD Non consentito OPN Permesso RES Riservato N.L Perdita della linea neutra CHE Controllo OP.
Parametro 1: È per programma alternativo. Ci sono 15 programmi da istituire. Fare riferimento alla tabella riportata in seguito. Parametro 1 Parametri 2 e 3 sono i parametri delle scelte d'impostazione o valori per ogni programma.
01: Voltaggio d’uscita Interfaccia 02: Frequenza uscita Interfaccia 60 Hz, CVCF mode 50 Hz, Normale modo ATO Impostazione Parametro 3: tensione in uscita È possibile scegliere le seguenti uscite di tensione nel parametro 3: 208 indica tensione d’uscita = 208Vac 220: indica tensione d’uscita = 220Vac 230: indica tensione d’uscita = 230Vac 240: indica tensione d’uscita = 240Vac Impostazione Parametro 2: frequenza uscita Impostazione della frequenza di uscita.
50 Hz: Campo di regolazione da 54,0 Hz a 51.0Hz. 60 Hz: Campo di regolazione è da 61.0Hz a 64.0Hz. Il valore predefinito è 54.0Hz/64.0Hz. IT 05: Modo ECO attivare o disattivare Interfaccia Impostazione Parametro 3: Attivare o disattivare la funzione ECO.
Parametro 3: 000 ~ 999: Impostare il tempo massimo d'autonomia da 0 a 999 minuti. L'UPS si spegnerà per proteggere la batteria, che arriva dopo il tempo impostato. Il valore predefinito è 990 minuti. DIS: Disabilitare la scarica della batteria, la protezione e il tempo dell'autonomia dipenderà dalla capacità della batteria. Interfaccia Impostazione Riservato per futura applicazione. 12: Rilevamento perdita neutro Interfaccia Impostazione Riservato per futura applicazione.
Interfaccia Impostazione Parametro 2: Selezionare "Add" o "Sub" la funzione della regolazione di tensione batteria della vera e propria configurazione. Parametro 3: la gamma di tensione è da 0 V a 9,9 V, il valore predefinito sono 0 V.
14: Regolazione del carica batteria Interfaccia Impostazione Parametro 2: si può scegliere Add o Sub per regolare la tensione del caricabatterie. Parametro 3: la gamma di tensione è da 0 V a 9,9 V, il valore predefinito sono 0 V. NOTA: * Prima di fare il cambio della tensione, accertarsi d'avere scollegato tutte le batterie, prima di modificare la tensione del caricabatteria. * Si consiglia di utilizzare il valore di default (0). Qualsiasi modifica deve essere adatta alle specifiche della batteria.
19: Uscita B, taratura della tensione Interfaccia Impostazione Parametro 2: si mostra sempre come OP.V * tensione di uscita. Parametro 3: mostra il valore interno di misura della tensione d'uscita B, ed è possibile calibrare premendo Su (Up) o Giù (Down) a secondo il valore di misura da una tensione esterna. Il risultato di calibrazione sarà effettivo premendo Invio. Il range di calibrazione è limitato all'interno di + /-9V. Questa funzione è normalmente utilizzata per il funzionamento in parallelo.
LCD display Non corrente Descrizione in uscita Quando in bypass, tensione / frequenza sono fuori portata accettabile o bypass è disabilitato (o proibito), UPS eroga corrente in uscita, se accendere o spegnere l'UPS. Ciò significa che l'UPS non ha alcuna uscita di corrente. Emettendo un segnale acustico di allarme ogni due minuti. LCD display Modo CA Descrizione Quando la tensione d'ingresso è nel parametro d'azione accettabile, UPS fornirà pura e stabile di alimentazione CA d'uscita.
IT Modo ECO Descrizione Quando la tensione d'ingresso è nel campo di regolazione della tensione e il modo ECO è attivato, UPS bypassa la tensione d'uscita per il risparmio energetico. LCD display Modo CVCF Descrizione Quando la frequenza d'uscita è impostata su "CF", l'inverter emette frequenza costante (50 Hz o 60 Hz). In questo modo, l'UPS non avrà l'uscita del bypass ma ancora carica la batteria.
LCD display IT Modo batteria Descrizione Quando la tensione d'ingresso / frequenza è oltre i valori accettabili o mancanza di tensione, L'UPS è alimentato dalla batteria ed emette un allarme acustico ogni 4 secondi.
IT Modo Bypass Descrizione Quando la tensione d'ingresso è nelle tolleranze d'azione accettabile e bypass è attivato, spegnere l'UPS e si entrerà in modo Bypass. Emettendo un segnale acustico di allarme ogni due minuti. LCD display Test batteria Descrizione Quando l'UPS è in modo AC o CVCF, premere il tasto "Test" per più di 0,5 s. Poi, l'UPS emette un segnale acustico e inizia il "Test della batteria". La linea di demarcazione tra I / P e le icone inverter lampeggia per ricordare agli utenti.
IT Avviso di Descrizione stato UPS Se alcuni errori nel sistema UPS (ma è ancora in esecuzione normalmente), sarà mostrata una schermata più a rappresentare la situazione di allarme. Nella schermata d'avviso, l'icona , e può visualizzare fino a 3 codici di errore e ogni codice indica un errore. È possibile trovare il significato del codice nella tabella dei codici di allarme. LCD display Errore di stato Descrizione Quando l'UPS ha un evento strano, lo inverter è bloccato.
3-9.
3-11. Codice d’avvertimento Codice 01 Evento Batteria scollegata 02 04 Codice 10 Evento Fusibile rotto IP L1 * IP perdita Neutro 11 Fusibile rotto IP L2 * IP fase anomala 12 Fusibile rotto IP L3 * 09 Sovraccarico 34 Sistema parallelo problema di linea differente. Bypass parallelo problema di linea differente Bypass bloccato per sovraccarico 3 volte in 30 minuti. Converter squilibrio di corrente 0A Ventilatore guasto 35 Fusibile batteria rotto.
4. Risoluzione dei problemi IT Se l’UPS non funziona correttamente, prego risolvere i problemi utilizzando la tabella sotto indicata. Sintomo Possibili cause Rimedio La linea AC di non è collegata Controllare se il cavo di Nessuna indicazione di allarme anche bene alla rete principale di alimentazione d'ingresso è se l'alimentazione è normale. potenza. collegato alla rete. L’icona e il codice indica con LCD display lampeggiante e allarme suona ogni secondo.
Sintomo Il codice d'allarme 02 è mostrato, l'icona lampeggia sul display LCD, e segnali acustici di allarme ogni secondo. Possibili cause Il cavo del neutro d’ingresso è scollegato. L'ingresso L2 o L3 fusibile è interrotto. 32 Rimedio Controllare e correggere il collegamento neutro d'ingresso.
5. Stoccaggio e manutenzione 5-1. Conservazione IT Se possibile per sicurezza prima dello stoccaggio caricare la batteria per 7 ore. Conservare l'UPS in posizione verticale, in ambiente coperto, asciutto e fresco. Durante la conservazione "stock", ricaricare la batteria in base alla seguente tabella: Temperatura di stoccaggio Frequenza di ricarica Durata della ricarica -25°C - 40°C Ogni 3 mesi 1-2 ore 40°C - 45°C Ogni 2 mesi 1-2 ore 5-2. Manutenzione L'UPS funziona con tensioni pericolose.
6. Specifiche MODEL CAPACITY* INPUT 1000 1000L 10000VA / 9000W 1500 1500L 15000VA / 135000W 3000 3000L 30000VA / 27000W 110 VAC(Ph-N) ± 3 % at 50% carico 176 VAC(Ph-N) ± 3 % at 100% carico Linea con tensione bassa + 10V 300 VAC(Ph-N) ± 3 % at 50% carico 276 VAC(Ph-N) ± 3 % at 100% carico Linea con tensione alta - 10V Sistema = 46Hz ~ 54 Hz @ 50Hz Sistema = 56Hz ~ 64 Hz @ 60Hz Trifase + neutro ≧ 0.