EP500Pro Power Station Please read this manual before use and follow its guidance. Keep this manual for future reference.
User Manual Please read this manual before use and follow its guidance. Keep this manual for future reference.
Contents 01. EP500Pro Introduction ............................. 01 02. General Safety Instructions ...................... 02 03. What`s in the Box .................................. 05 04. APP........................................................ 07 05. Features of EP500Pro .............................. 11 06. Startup & Power off ................................. 12 07. User Interface ....................................... 13 08. How to Recharge EP500Pro (INPUT) ...........20 09. Discharge (OUTPUT) ...
Just Power On 01. EP500Pro Introduction 1.1. Introduction ●BLUETTI is proud to take the energy storage world by storm with the release of its first home energy storage system series - the EP500Pro with four smoothrolling transport wheels, the EP500Pro was not designed to be a large solar battery mounted on the wall or in the garage.
BLUETTI 1.2. Abbreviation ● BMS: Battery Management System ● MPPT: Max. Power Point Tracking ● SOC: State of Charge ● UPS: Uninterruptible Power Supply ● AC: Alternating Current ● DC: Direct Current ● PV: Solar Panel(s) Charging(Photovoltaic) ● Grid: Home Power Supplied by Utility ● T500: 500W additional charger ● DOD: Depth of Discharge ● ECO Mode: A power - saving mode for the EP500Pro, the AC output ports are automatically turned off if the load is less than 30W over a span of 4 hours. 02.
Just Power On ● Warning: DO NOT insert foreign objects into any ports of EP500Pro (both AC & DC & ventilation holes). EP500Pro generates the same potentially lethal AC power as a household wall outlet. Please use EP500Pro carefully and keep children away from it. ● If necessary, only the dry powder fire extinguisher is suitable for the product. ● For safety purposes, please use only the original charger and cables designed for the equipment.
BLUETTI and grasp the correct method of operation. ● Trained personnel: personnel who have undergone corresponding technical training and have the necessary experience to be aware of the danger that may be brought to him during the operation, and can take measures to reduce the danger to himself or other personnel to at the lowest limit. ● The replacement of equipment or parts (including software) must be done by professionals or authorized personnel. 2.1.2.
Just Power On 2.2. Installation environment requirements ● When the equipment is running, please do not block the vents or the heat dissipation system in order to prevent high temperatures and/or fires. ● The equipment should be installed in an area away from liquids. It is forbidden to install it near or below water pipes, air outlets and other locations that are prone to water condensation.
BLUETTI Additional Purchase Accessories Sold on BLUETTIPOWER.COM No. Picture Category Split Phase Box Pro (P030A) 7 To double the capacity, power of output and voltage. 12V/30A XT60 to Aviation Plug 12V/30A RV Cable 8 For 30A DC Output. XT60 to SPC45 To support DC power supply for RV. Generator Charging Cable 9 10 Charging EP500Pro via generator. Lead-acid Battery Charging Cable Charging EP500Pro via Lead-acid battery. Car Charging Cable 11 Charging EP500Pro with cable No3.
Just Power On 04. APP Please make sure the state of Bluetooth & Wi-Fi settings is “ON” before connecting EP500Pro with BLUETTI App. (Homepage - Settings - Next - Next) Step 1: ● Please search “BLUETTI” on the App Store (for IOS devices) or Google Play (for Android devices) to download the BLUETTI App to remotely control your EP500Pro. ●EP500Pro can be controlled via Bluetooth or Wi-Fi.
BLUETTI ● Check your email account you used in the BLUETTI App for the verification code sent from BLUETTI and fill in the activation code located within the email to activate your BLUETTI account. Step 2： ● Scan the unique QR code on EP500Pro to add the unit on the available device list on the App, and fill it with the password of your 2.4G Wi-Fi network to activate the communication function of EP500Pro for data syncing.
Just Power On ● The basic information can be viewed after the unit is connected with App successfully. Press ‘’gear icon’’ to customize the current working mode and parameters of your EP500Pro under “Settings”. ● The BLUETTI App supports a “Firmware Update” function which allows access to the latest software upgrades for continued features, improvements and fixes.
BLUETTI Note: Please keep your phone 5m/16.4ft within the EP500Pro for a better connection during update. Also, if BLUETTI APP fails to connect to the Internet. Tap "Settings" at the homepage of your phone and scroll down until the BLUETTI App shows up(IOS). Tap "Settings" on homepage of your phone, tap “Application Management” and select BLUETTI(Android). Tap the BLUETTI icon and verify that "Wireless and Data" permissions are enabled. User cannot turn on EP500Pro via BLUETTI App.
Just Power On 05. Features of EP500Pro 1 2 3 5 7 4 6 8 9 10 14 11 12 13 12V/30A Port Touchscreen 12V/10A Cigarette Lighter Port AC Output Port(30A MAX) 12V/10A DC5521 Port AC Output Port(20A MAX) USB-C (PD3.
BLUETTI 06. Startup & Power off （ Back ） （ Front ） ● Turn on the main power switch located on the back of EP500Pro. ● Power On: Long press the power button. The power button indicator will illuminate. ● Power Off: Long press the power button. The power button indicator light will turn off. ● EP500Pro will turn on automatically from Power Off status when either grid charging and/or PV charging is applied on. ● DC and AC power switch are accessible on the Touchscreen.
Just Power On 07. User Interface 7.1. Main Interface Tip: The LCD resistive touchscreen, recommended to press lightly with the edge of your fingernail until it "beeps" when it registers a press. (NOTE: Touchscreen sounds can be disabled in the Settings menu). e f g a l b k c d h i j a . Homepage g . Date/Time b . Settings h . DC load Information c . Data i . DC ON/OFF d . Alarm j . AC ON/OFF e . PV Charging Information k . AC load Information f . BMS Information l .
BLUETTI 7.2.1. AC Output Voltage & Frequency ● NOTE: Please check the output voltage, frequency, and other parameters BEFORE using EP500Pro for the first time. The EP500Pro 100-120V AC version cannot be set to 220-240V AC output. ● The Output frequency and voltage can only be tweaked when the AC is OFF(tap the AC icon at homepage to turn off AC output if it`s ON). ● The list of standard output voltage and frequency in 5 regions or countries. You may tap on the screen to set the parameters as needed.
Just Power On 2 1 3 2 1 4 3 1 2 3 4 a, Connect your solar panels in series into PV charging cable. b, Plug the Aviation plug into the middle input port(CP2) on EP500Pro. 7.2.3. Language Setting & ECO Mode Press “English” or “Japanese” icon to set as the default system language to be displayed on your EP500Pro. ECO: When ECO is turned ON, if the AC output load is less than 30W for 4 hours,the AC ports will be shut off for power-saving.
BLUETTI 7.2.4. Machine Type (for split phase setting, exclusive for 100-120V Version) Please turn to Chapter11 for detailed installation. 7.2.5. Working Mode(Homepage - Settings - Next - Working Mode) Tips: EP500Pro will be set as the Standard UPS Mode as default. There are altogether four working modes you can select in settings: Standard UPS Mode: Default working mode(Offline mode). PV Priority Mode: Recommended for areas in stable power supply.
Just Power On 7.2.6. Max. Grid Input Current ● Please check the specification of your grid, sockets, connections, wires, etc. to determine the maximum allowable current that can be drawn by the EP500Pro. BLUETTI is not liable for any damages, injuries, or any other legal responsibility incurred directly or indirectly from changes made to this setting. ● Max. Grid Input Current: limit the Max.
BLUETTI 7.3. Data In the Data section, you may view Product Info, Inverter & Charger Info, BMS Maintenance, and Alarm/Fault History by selecting each respective button. 7.3.1. Product Info ● When you select the “Product Info” button, you can view the product model, serial number (SN), control software version, monitoring software version, BMS monitoring software version and display software version. ● The Serial Number (SN) can also be used to pair to BLUETTI APP manually. 7.3.2.
Just Power On adapter charging, DC output and AC output working status. This section can also be accessed directly from the shortcut icon on the homepage. 7.3.3. Battery Information By tapping the “Battery Information” button, user can view the live information of the status of the battery pack. This section can also be accessed directly from the shortcut icon on the homepage. 7.3.4. Alarm History Tap the “Alarm History” button, user can view all the alarm information generated by the machine.
BLUETTI 08. How to Recharge EP500Pro (INPUT) ●The EP500Pro includes two charging ports which can be recharged in different methods. They will be covered in three different sections according to which port(s) are being connected. ●The two ports are named as Aviation Charging Port 1 [CP1] and Aviation Charging Port 2 [CP2]. Aviation Port 1 (CP1) Generator Wall Outlet Solar Panel Second Adapter Aviation Port 2 (CP2) Car Lead-acid Battery 8.1.
Just Power On @1500W/100Vac , @1800W/120Vac Max . The charging process will automatically stop when it reaches 100% capacity. Additionally, you can choose to access the BLUETTI Sub Panel or the L14-30 receptacle, the maximum charging power allowed will be up to 3000W. Main Panel Sub Panel Charging via Sub Panel Charging via wall outlet 8.1.2.
BLUETTI nd 8.2. CP2 (2 Pin1:DC1 Pin2:DC2 Pin3:DC1 Pin4:DC2 Charging Port) Pin4 Pin3 Pin1 Pin2 PV+ PV+ PVPV- 8.2.1. Charging Method 3: Solar Panels (via 4pin aviation-MC4 cable) ●For regular solar panels: EP500Pro(dual MPPT) supports two PV charging methods with regular portable panels and rigid panels. Max current for single circuit: 12A. Voltage Range: 12-150V. Max. Input Power: 2400W. a.
Just Power On ●For Roof/Rigid Panels: If you choose roof panels to be the solar power source to recharge EP500Pro, connect your roof panel with MC4-Aviation to EP500Pro through PV Step Down Module will finish the installation. PV Module (additional accessories) is required to drop down the voltage if the open circuit voltage produced by your roof panels exceeds the limit of EP500Pro can handle: 12-150VDC, 12A*2.
BLUETTI 8.2.3. Charging method 5: Lead-acid Battery Charging ●Connect to the positive and negative poles of the battery through the battery charging clamp(pay attention to distinguish the positive and negative poles of the battery, the red pole on battery indicates the positive pole, and the black one for negative pole). ●Enter “Settings” on touchscreen to set DC input source to “Others”. Note: Select DC1 or DC2 Input Source according to the the certain DC cables(check the label on cable No.
Just Power On 8.3. Dual Charging Aviation Port 1(CP1) Generator Wall Outlet Solar Panel Second Adapter Aviation Port 2(CP2) Car Lead-acid Battery Charging Method 6 : Supports charging the EP500Pro with CP1 and CP2 at same time. You can use any charging methods listed previously, simultaneous,to maximize charging power input. They are listed here again for your convenience. Select the method for both CP1 and CP2 to Dual Charging.
BLUETTI DC Input2: Method a: Solar panels(Set DC 2 Input Source as “PV” in “Settings”) Method b: T500 Adaptor(Set DC 2 Input Source as “Others” in “Settings”) Method c: 12V/24V Car Charger/Storage battery(Set DC 2 Input Source as “Others” in “Settings”) Method d:PV Parallel (PV parallel needs to be set in “Settings”) 8.4. How to calculate the recharging time of EP500Pro 5120Wh / Total recharging power + 0.
Just Power On 09. Discharge (OUTPUT) The operational time of the EP500Pro is subject to many different factors such ambient temperature, discharge rate, remaining battery capacity, and other factors. 9.1. The Output Port 9.1.1. AC Output Port ●EP500Pro is equipped with *5 AC(US, JP version) / *3 AC(AU,EU,UK) outputs with a continuous 3000W Max. power of output in total, and the ability to support surges up to 6000W.
BLUETTI 9.1.1. DC Output Port 1. *1 RV port Special 30A output port can be adapted to appliances widely, perfect for RV. 2. *1 Cigarette lighter port 7 Output port for devices with corresponding plug such as vehicle-use vacuum, mini refrigerator. 3. *2 DC 5521 Traditional ports for routers/cameras, old laptop etc. 4. *2 USB-C 1 2 3 4 Can be used via USB-C to USB-C cable to charge most devices in the market such as Pixel Phone, Macbook Pro at 100W Max. 5.
Just Power On ●Tools Bench Grinder 1400W 2.9 Hrs Welding Machine 1800W 2.3 Hrs Circular Saw 1400W(2300W) 1.7-2.9 Hrs ●Transportation Electric Vehicle(16A) 1800W 11.2-13.3 Miles E-Bike 500W 7.6 Times （ The estimation operating time is only for reference ） 9.3. How to Calculate the Operation Time ●5120Wh * DOD * η / (load W) = operation time (unit: hour/time) If I want to know how many times 96W Macbook Pro could be recharged.
BLUETTI 10. UPS 10.1. UPS Description An uninterruptible power supply or uninterruptible power source (UPS) is an electrical apparatus that provides emergency power to a load when the input power source or mains power fails. A UPS differs from an auxiliary or emergency power system or standby generator in that it will provide nearinstantaneous protection from input power interruptions, by supplying energy stored in batteries, supercapacitors, or flywheels. 10.1.1.
Just Power On Non-critical Load ≥2000W/3000W or ≥4000W/6000W Grid Main Panel BLUETTI Sub Panel Solar Panel BLUETTI PV Module EP500 & EP500Pro Critical Load ≤2000W/3000W or ≤4000W/6000W ( EP500Pro grid-tied home power back-up system with Sub Panel and roof panels ) 1 3 2 ( Plug-in UPS system ) 10.1.3. Turn On UPS Function ●Select “Setting” on the main touchscreen interface. Select “Next” and select “Working Mode” to choose UPS Mode. ●The default working mode is “Standard UPS Mode”.
BLUETTI 10.2. Enable UPS Running Mode 10.2.1 Standard UPS Mode ●Offline UPS: Basic UPS Working Mode EP500Pro will power your load directly from the grid and maintain a 100% charge. When grid power fails, the EP500Pro switches to internal batteries. 10.2.2. Time Control UPS Mode ●This allows you to set the times that EP500Pro will be charged via grid power and the times to run loads from its battery.
Just Power On 10.2.3. PV Priority UPS Mode ●PV Priority Mode: This mode is recommended for areas with stable grid power. The battery will be recharged mainly by PV for power savings. ●Note: In PV Priority Mode, EP500Pro can only be recharged via grid to 30% capacity, and also discharge to 30% of the capacity (you can tweak it to 100% for full grid charging manually on touchscreen or App) as the " Reserved capacity for PV charging".
BLUETTI 10.2.4. Customized UPS Mode ●Charge/Discharge time, and High/Low Battery SOC can be set in this UPS mode. ●Ability to disable the grid charging. The unit will not charge batteries from grid. ●Apart from Time Control UPS, the main switch of grid charging and time mode settings are involved. The setting of turning the grid/time setting ON/OFF will take effect on both PV Priority Mode and Time Control Mode.
Just Power On 11. Split Phase Function Note: (1) Please disconnect the AC charging cable for both EP500Pro units while binding into split phase box. (2) Certifcated Technician is required to build the split phase system to power the Power Cabinet or Sub Panel. Warning: If you insist to charge the EP500Pro which has been connected into split phase box already, please make sure the L1/L2/N wire is set at the right place or the EP500Pro will be damaged.
BLUETTI Box Pro. Step 2: Plug the communication cables from each of the two EP500Pro’s to the Split Fusion Box Pro. Step 3: Set the Machine Type to "Split Phase" on EP500Pro either. Step 4: Select "Master" or "Slave" on the operating EP500Pro. Select "Master" will set the operating EP500Pro as the one to control both two EP500Pro. Select "Slave" will set the operating EP500Pro as the other EP500Pro as the "Master" one.
Just Power On X(L1) W(N) Y(L2) G(PE) L1 PE L2 N AC Input Cable(L14-30) L1 N PE L2 N PE WRONG CONNECTION It`s forbidden to connect EP500Pro into Split Phase System when AC charging is ON, please use AC Input Cable(Optional Purchase) to charge both of your power stations in Split Phase System. Wrong Connection will damage the battery inside the power station and your warranty will be invalid.
BLUETTI 12. Technical Specification EP500Pro JP Model EP500Pro US EP500Pro EU/UK/AU Net Weight 83kg (183.0lbs) Dimensions 580*300*760mm (22.8*11.8*29.9in) Charge Temperature 0-40℃ (32-104 ℉ ) Discharge Temperature -20-40℃ (-4-104 ℉ ) Storage Temperature -25-40℃ (-13-104 ℉ ) Working Environment 10-90% Humidity Certification PSE, FCC, CE, UN38.3, msds, UL, SAA and ROHS Capacity 5120Wh (100Ah) Battery Type LiFePO4 Standard Battery Voltage 51.2VDC Battery Cell Voltage Range 44.8-57.
Just Power On Rated Output Voltage 100VAC 120VAC Rated Output Frequency 50/60Hz Rated Continuous Power 3000W Rated Output Current 30A 220-240VAC 25A 13A 3100W ＜ load ＜ 3750W, 2min; Power of Over-load 3750W ＜ load ＜ 4500W, 5s; 4500W ＜ load ＜ 6000W, 500ms Efficiency >88% THD <5% DC Output Cigarette Lighter Port *1 12VDC/10A DC 5521 *2 12VDC/10A USB-A *2 5VDC/3A total USB-A(fast charging) USB-C (Type-C) *2 *2 20VDC/5A; 5-15VDC/3A Wireless Charging Pad RV Port 3.6-12VDC/36W *2 5W/7.
BLUETTI Max. Input Voltage 150VDC MPPT Voltage Range 12-150VDC Max. Power of Input 1200W*2 Rated Input Current 12A*2 13. Storage and Maintenance ●Please turn off the unit and charge it to 50-70% of capacity before storing. ●To help preserve battery health, please discharge and fully charge the unit atleast once every 6 months. ●Ensure proper ventilation when in use or in storage. ●Keep unit away from any combustible materials or gases. (32-113 ℉ , 0-45℃ ).
Just Power On 14. Troubleshooting Error Code Error List Troubleshooting 001 D-AMCU Warning Please contact with the dealer if the error still exists after rebooting the unit. 002 D-BMS Warning Please contact with the dealer if the error still exists after rebooting the unit. 003 D-A Communication Error Please contact with the dealer if the error still exists after rebooting the unit.
BLUETTI 015 DC Input Voltage High Please contact with the dealer if the error still exists after rebooting the unit. 016 DC Input Voltage Low Please contact with the dealer if the error still exists after rebooting the unit. 017 DC Input Over Current Please contact with the dealer if the error still exists after rebooting the unit. 018 Inverter Output Over Current 019 Inverter Voltage High The output power of load exceeds.
Just Power On 027 Load Relay Short Circuit Please contact with the dealer if the error still exists after rebooting the unit. 028 Load Relay Open Circuit Please contact with the dealer if the error still exists after rebooting the unit. 029 INV Soft-Start Failure Please contact with the dealer if the error still exists after rebooting the unit. 049 PV1 Over Current Please contact with the dealer if the error still exists after rebooting the unit.
BLUETTI 062 Multi Address Error 063 Multi Synchronization Error Please check whether the communication cable is connected correctly. Clear the alarm history or restart the unit. Please check whether the communication cable is connected correctly. Clear the alarm history or restart the unit. 064 Multi Brak Phase Error Please check if the input of the AC voltage meets the specifications of the unit. Clear the alarm history or restart the unit.
Just Power On 090 DC12V/10A Output Current High Please disconnect the appliances on DC 12V/10A ports. Clear the alarm history or restart the unit. 091 DC Output Soft Start Failure Please contact with the dealer if the error still exists after rebooting the unit. 092 DC12V/30A Output Short Please disconnect the appliances on DC Circuit output ports. 093 DC12V/10A Output Short Please disconnect the appliances on DC Circuit output ports.
BLUETTI 107 NTC Faulty Please leave the unit at the recommended temperature few hours to recover. Please contact with the dealer if the error still exists after rebooting the unit. 108 Fan Faulty Clean or replace the fan to ensure proper ventilation. Please contact with the dealer if the error still exists after rebooting the unit. 15.
Just Power On There are two types of working conditions of UPS for EP500Pro. No delay for online UPS; 20ms from offline UPS. ●Can I connected my two EP500Pro with Fusion Box to achieve double the output power, voltage and capacity. You can connect two EP500Pro OR two EP500Pro with a Fusion Box. The units must be of the same type and the correct Fusion Box (P020A for EP500Pro, P030A for EP500Pro). You cannot mix a EP500Pro and EP500Pro with a Fusion Box.
BLUETTI 16. Declaration ●Some changes may not be noticed specifically such as appearance or specifications due to the exterior material or hardware improvement of the product. ●Our company shall not be liable for any damage caused by force majeure such as fire, typhoon, flood, earthquake or the user's intentional negligence, misuse or other abnormal conditions. ●No compensation for damages shall be made for utilizing non-standard adapters and accessories.
P/N:17.0303.
