Important READ and understand this manual BEFORE using this firearm Instruction Manual for Viper .50 cal. BMG Single Shot Rifle Bluegrass Armory P O Box 1293 Richmond, KY 40476 859-625-0874 www.bluegrassarmory.com This manual must remain with firearm at all times. If this manual is lost or destroyed a new one can be obtained from Bluegrass Armory or downloaded from our website. www.bluegrassarmory.
TABLE OF CONTENTS INTRODUCTION…………………………2 WARRANTY…………………..………….3 BASIC SAFETY…………………………..4-5 DESCRIPTION……………………………6 CLEANING & MAINTENANCE ………..7 PARTS LIST………………………………8-10 AVAILABLE OPTIONS…………………11 EXPLODED VIEW………………………12 Everyone at Bluegrass Armory would like to take a moment of your time to say thanks for purchasing a Viper.
Warranty The Viper has a one-year warranty against manufacturing defects. Normal wear and or abuse are not covered by warranty. Bluegrass Armory is not responsible for accidents, injuries or death due to misuse, abuse or improper handling of this firearm. The purchaser of this firearm is the responsible party and should take any and all precautions to see it is used properly. Caution: Read this manual carefully before handling or loading your Viper.
Never point any gun, loaded or unloaded, at anything you do not intend to shoot. BASIC SAFETY • • • • • • • • • • • • • • • • • • • • Anyone using or handling this firearm must have read and thoroughly understood this Instruction Manual. Always handle your Viper as if it is loaded and ready to fire. Be sure muzzle brake is properly attached before loading or firing. Failure to do so could result in serious bodily harm or death, due to extreme recoil. Be sure the barrel is free of all obstructions.
• • • • • • • • • • • • • Never transport loaded firearms in a vehicle or on an ATV. Must have 3 1/2” minimum eye relief scope. Store guns and ammunition separately, under lock and key, and beyond the reach of children. Never pull a gun toward you by the muzzle. Use only ammunition of the correct caliber, properly sized casings, bullet style and diameter. Never carry a loaded firearm.
Description Specs: Caliber: .50 BMG Weight: 24 lbs. Unloaded-no scope Overall Length: 57 in. (145cm) Barrel Length: 26 in. to 32 in. 29” Standard Length of Pull: 15in. to 17 in.
Cleaning & Maintenance Keep barrel and chamber clear. 1. Open bolt and check chamber. 2. With bolt open, remove bolt handle by turning counter clockwise. 3. Remove the 2 rear pushpins. 4. Slide Recoil Assembly off rear of rifle. 5. Bolt will slide out rear of rifle. 6. Remove the 2 front pushpins. 7. Trigger assembly will lower straight down out of stock. Clean all steel pieces with soft rag and good quality gun oil. Aluminum parts are to be cleaned with mild soap solution.
Parts List *Available only through a licensed gunsmith.
Main Frame Stock Barrel Barrel screw-3 Barrel nut Receiver Muzzle Brake-Aluminum Muzzle Brake shim-set Primary Extractor pins-3 Assembly pin 2200-xx* 2204* 2000-xx* 2001-xx* 2002 2003 2004* 2005 2006 2007* 2009 Bolt Assembly Bolt Firing pin Firing pin spring Bearing retainer Extractor Extractor pin Extractor pin spring Ejector Ejector spring Ejector retainer Bearing Bolt handle 3200* 9 3000* 3001 3002 3003 3004 3005 3006 3007 3008 3009 3010 3011
Recoil Pad Assembly Recoil pad Recoil plate Recoil pad screws-2 Lower stock Rear plug Lower stock screw-2 Rear plug screw-4 Detent retainer pin-2 Detent-2 4001 4002 4003 4004 4005 4006 4007 4010 4011 Bi-pod Extension lock cover screw-8 Leg pivot screw-2 Pivot spring-2 Pivot lock pin-short-2 Pivot lock pin-long-2 Extension lock spring-2 Extension lock-2 Yoke Leg-upper-2 Leg-lower-2 Foot screw-2 Extension foot-2 5000 5001 5002 5003 5004 5005 5006 5007 5008 5009 5010 5011 10
Accessories Bi-Pod-complete Bi-Pod Mounting Pin Instruction Manual Muzzle Brake Wrench Barrel Nut Wrench Weight Kit Cleaning Rod Small Wrench Set Scope Rings Assembly pins-handle Muzzle Brake-Steel 5022 2010 6001 6002 6003 6004 6005 6006 6007 6008 6010 11
031106 Rev.
