SENSE: USER GUIDE Read Me to Get the Most Out of Your Device...
Speaker Multi-Function Button (the symbol) Battery Indicator Touch-Sensitive Volume Controls Charge Port On/Off Switch ENGLISH BlueAnt SENSE Microphone BlueAnt 3
1: Charge Your SENSE Before using your SENSE, charge it using the supplied USB cable and charger: > A full charge takes about 2.5 - 3 hours. > During charging, the battery indicator light turns red. > When the light goes out, the charge is complete. Tip: You can also charge the SENSE by connecting to your computer’s USB port.
ENGLISH 2: Pair the SENSE with your Phone 1. Slide the power switch to the ON position. 2. The SENSE will announce the available languages. Tap the symbol when you hear your language. 3. The SENSE will now talk you through the pairing process. Slide the switch to power on then follow the prompts 4. The pairing code is 0000 (four zeros). Note: your BlueAnt SENSE will appear in the Bluetooth menu on your phone as the “BlueAnt S3”.
3: Transfer your Phonebook Once the pairing is complete your SENSE will attempt to transfer the contacts from your phonebook so that it can announce the names of incoming callers. On most phones this happens automatically. If your phone asks you to allow a connection to the “BlueAnt S3”, you must select “YES” or “OK”. BlackBerry® If you are using a BlackBerry smartphone you may see a message like this one. Select “Don’t ask this again” so that a tick appears in the box, and then choose “YES”.
Phonebook Access Request On some Android devices a message about the phonebook transfer appears at the top of the screen. You must swipe your finger over this message and accept the phonebook transfer request. Automatic Transfer Not Supported Notification shown on Android devices ENGLISH Android™ Some phones do not support automatic phonebook transfers. If this is the case for your phone the SENSE will announce that it cannot transfer the contacts automatically.
4: Install the SENSE in your Car 1 Slide the clip onto the back of the SENSE until it clicks into place. 2 Slide the SENSE onto your car sun visor. Don’t forget: Drive safely and within the law. Please refer to the relevant national or local legislation regarding the usage of mobile devices while driving. Remember that driving is your first priority: please read the enclosed safety information booklet for tips on the safe use of your BlueAnt device.
When the phone rings, the SENSE will announce the caller’s name or number and ask you if you want to take the call. Wait for the prompt to finish, and then say Answer or Ignore: 1 Call from John Smith, answer or ignore? Or: tap the Tip: Tap the 2 ENGLISH Answering Calls Answer symbol at any time to answer the call. Double tap to ignore. symbol to hang up and end the call.
Making Calls If your phone supports voice dialing over Bluetooth you can make calls using your voice: 1. Tap the symbol. 2. The SENSE activates your phone’s voice dialing functionality. Please refer to your phone’s manual for details on the commands you can use to control your phone. Tip: Tap the symbol to hang up and end the call. Note: Your phone must support voice dialing over Bluetooth: > The Apple iPhone 3GS (running firmware 3.
Swipe your finger across the top of the SENSE to adjust the volume: To decrease the volume swipe from + to - ENGLISH Adjusting the Volume To increase the volume swipe from - to + Adjusting the volume when you are not on a call sets the volume of the voice prompts. Adjusting the volume during a call will change the loudness of the caller’s voice.
Redial and Call Back > Hold down the + symbol for about 3 seconds to redial the last outgoing call. > Hold down the - symbol for about 3 seconds to call back the last incoming call. Switching Between Multiple Calls (Call Waiting)* > Tap the - symbol to end your call and answer an incoming call. > Tap the + symbol to put your call on hold and answer an incoming call. > Tap the + symbol to switch between an active and a held call. * To use this feature, your phone and network must support call waiting.
To pair another phone, put your SENSE back into pairing mode by holding down the symbol for about 6 seconds. > Your SENSE can store pairing information for up to 2 phones. ENGLISH Pairing Another Phone / Multipoint > Your SENSE can connect to up to 2 phones at the same time (multipoint). When 2 phones are connected at the same time: > You can answer calls on either phone through the SENSE. > Each time your phones reconnect to the SENSE the one that connects first becomes the “primary phone”.
Transferring your Phonebook Contacts Your SENSE uses Text To Speech technology (TTS) to read out the name of the person who is calling you. To do this, the SENSE needs to store a copy of your phonebook contacts. Automatically Transferring your Phonebook Contacts When you pair your phone with the SENSE it will attempt to transfer the phonebook contacts automatically. The SENSE stores up to 2,000 contacts per phone. Tip: Tap the symbol to cancel the phonebook transfer.
2. Go to your phonebook and select the contacts you want to send to the SENSE. Choose the option to “Mark All” or “Select All” if this is available on your phone (if this is not available, you will need to transfer each contact individually). 3. Select the option on your phone to “send” or “beam” contacts, business cards, or v-cards via Bluetooth, and select the “BlueAnt S3” from the list of Bluetooth devices. See your phone’s manual for help with this step. ENGLISH 1.
Reconnecting to the SENSE Your SENSE includes a sensor that detects the vibration of your car door. This means that the SENSE will automatically reconnect to your phone when you get back in the car. If the SENSE does not connect to your phone for any reason, tap the SENSE to reconnect to your paired phone.
Note: When there are two phones connected, only the primary phone can play music through the SENSE via A2DP. Reset the SENSE ENGLISH The streaming audio mutes automatically if the phone rings. If you are having problems with your SENSE, you can reset and start again: 1. Delete any pairing information from your phone’s Bluetooth pair list. (Remember that the SENSE will be listed on your phone as the “BlueAnt S3”). 2. Turn your phone off. 3.
Specifications > Bluetooth version 2.1 + EDR > Supported Profiles: HFP 1.5, A2DP 1.2 > Operating Range: Up to 10 meters > Frequency: 2.4 GHz > Talk Time: Up to 20 hours > Standby Time: Up to 600 hours > Charging Time: 2.5 hours > Battery Type: Rechargeable Lithium Ion Help and Support If you are having trouble getting the SENSE to work, please visit www.blueantwireless.com for online help, support, and troubleshooting tips.
By using this product, you are agreeing to BlueAnt’s terms and conditions, available at www.blueantwireless.com and on the supplied warranty information card. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by BlueAnt Wireless is under license. ENGLISH Terms and Conditions Android is a trademark of Google Inc., Apple and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
HELP AND SUPPORT Visit register.blueantwireless.com to register your BlueAnt device. Visit blueantwireless.com/geekspeak to watch and learn with our how-to videos for your BlueAnt device. Visit blueantwireless.com/support for online help and support or to contact the BlueAnt Technical Support team. Visit blueantwireless.com/buy to buy BlueAnt products, accessories and spare parts.
