User's Manual

T1 Quick Start Guide: English
1
Vol - Vol +
Multi-
Function
Button
(MFB)
Microphones
Indicator
Light
Charging
Port
Charge Your T1
Your T1 has been given an initial partial charge to get
started, but for best results charge it using the supplied USB
cable and adaptor until the indicator light turns
solid white.
> Charge the T1 whenever it announces that the battery is
Very Low.
> A full charge takes about 2 and a half hours.
> During charging, the indicator light fl ashes red.
> When the light goes solid white, the charge is complete.
> For safety reasons, the T1 automatically turns off during
charging.
2
Pair Your T1
1. Turn the T1 on by
sliding the power
switch on the back to
the green on position.
2. Put the T1 in your ear.
3. The fi rst time you use the T1 it will go straight to pair
mode and talk you through the pairing process.
For subsequent pairings, make sure the T1 is not
connected to any phones, then hold down the MFB. The T1
will announce that it is going into pairing mode.
Tip: The pairing code is 0000 (four zeros).
3
Power switch (on)
Upload Your Phonebook
Once the pairing is complete, your T1 will attempt to copy
the contacts from your phone’s address book so that it can
announce the names of incoming callers. Please wait for the
phonebook upload to fi nish before using the T1.
Some phones do not support automatic phonebook
transfers. If the T1 announces that it cannot automatically
transfer contacts, you need to go to your phone’s address
book and select the option to send contacts via Bluetooth to
the T1. See www.blueantwireless.com for help with this.
Note: Whenever you add contacts to your phone in future
you must update your phonebook on the T1: with the T1
connected to your phone but not on a call, hold down the
MFB for 1 second to initiate a phonebook update.
4
Wearing the T1
You can wear your T1
on either ear.
For best results:
> Position the hook and
ear gel as shown here.
> Make sure the T1 is angled
towards your mouth.
Protective Skins
Your T1 is supplied with optional rubber
skins to protect against dust and
moisture.
5
RIGHT
EAR
LEFT
EAR
Making Calls
Use your voice to make calls:
1. Click the MFB and wait for the T1 to ask you
to Say A Command.
2. Say Phone Commands to activate the voice
dial feature on your phone.
Alternatively:
> Simply dial the number on your phone and the audio will
automatically transfer to the T1.
> Hold down Vol + for 1 second to redial the last outgoing
call.
6
Taking Calls
When the phone rings, you can answer the
call with your voice: wait for the prompt to ask
you if you want to take the call, and then say
Answer or Ignore.
If you don’t want to wait for the prompt, or you
are in a noisy place:
> Click the MFB once to accept the call.
> Double click the MFB to reject the call.
During a call, click the MFB to end the call.
7
Voice Commands
To use any of the voice commands, click the MFB, wait for
the T1 to ask you to Say A Command, then say the command:
> Check Battery — Tells you the battery level on the T1 and
the connected phone (if supported by your phone).
> Call Information — Calls an information service number
stored in your headset.
> Phone Commands — Activates your phone’s voice dialing
feature (if available on your phone). Depending on your
phone model, you may need to record voice tags on the
phone to use this feature.
8
Listening to Audio
The T1 supports A2DP audio streaming: if your phone or
Bluetooth device supports the A2DP profi le then you can
simply start playing music or any other audio and it will
automatically transfer to the T1.
The audio will pause automatically if you make or receive a
phone call, and resume when the call ends.
9
Multipoint
Up to 2 phones can connect to the T1 at the same time. To
pair a second phone:
1. Use the phone’s Bluetooth menu to disconnect the existing
paired phone from the T1.
2. With the T1 switched on, hold down the MFB until the T1
starts to talk you through the pairing process.
3. When the pairing is complete, use the phone Bluetooth
menus to reconnect both phones to the T1.
When you have 2 phones connected, you can always answer
a call on either phone. If you initiate a call through the T1
the call will happen on the “primary phone”: the one that
connected to the T1 fi rst.
10
Advanced Button Functions
> To hold an active call and switch to an incoming or held
call, click Vol +
> To end an active call and answer a new incoming call,
click Vol -
> If your phone and network support call conferencing, you
can conference two active calls together by holding the
MFB for 3 seconds.
> Click Vol + and Vol - together during a call to transfer
audio to the phone.
> Hold Vol + and Vol - together for 1 second during a call to
mute and unmute the T1 microphone.
11
Advanced Button Functions
> Whenever you add contacts to your phone you must also
update your phonebook on the T1: with the T1 connected
to your phone but not on a call, hold down the MFB for 1
second to initiate a phonebook update.
> To turn the fl ashing indicator light on or off, disconnect
the T1 from your phone and hold down Vol + and Vol - for
1 second.
12
Upgrades
To enhance your experience, we are continually improving
the T1 software.
From time to time we will make feature enhancements
available on our website for you to download and apply to
your T1.
Go to www.blueantwireless.com to get the latest software
for your T1.
13
Problems?
If you are having problems with the T1, you can reset the T1
and your phone and start again:
1. Disconnect the T1 from your phone by deleting the pairing
from your phone’s Bluetooth menu.
2. Turn your phone off and back on again to clear its memory.
3. With the T1 switched on, but not connected to any phones,
click all three buttons (Vol +, Vol -, and the MFB) together.
The T1 will go reset and go straight to pairing mode.
You will now need to pair your phone with the T1 again.
14
Help and Support
This guide is just to get you started with the T1. If you
are having trouble getting the T1 to work, please visit
www.blueantwireless.com for online help, support, and
troubleshooting tips.
You can also follow the links to register your T1 for access to
fi rmware upgrades.
Please call us before returning the T1 to a store and we will
help you through any diffi culty you may have.
In North America call 1 866 891 3032.
In other countries please see www.blueantwireless.com for
your local support number.
15
Terms and Conditions
By using this product you are agreeing to BlueAnt’s terms
and conditions, available at www.blueantwireless.com.
Warning: All BlueAnt headsets are designed to reach
volumes of up to 100 decibels. Prolonged use at high
volumes may affect your hearing capacity. Using for
extensive time periods may result in noise induced hearing
loss (NIHL).
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by BlueAnt Wireless is under license.
© 2010 BlueAnt Wireless. All Rights Reserved.
16