7310 ENGLISH ver 19-01
EN 7310 Congratulations on the purchase of your new 8STREME 7310 pool cleaner. It is a powerful autonomous robot delivered ready to use. Ideal for pools of all sizes and in all forms. This robot comes with an easy accessible debris basket along with floating rotary coupling which limits cable entanglement. Please check the package to make sure that all parts are ready to be installed.
EN Table of contents 01 Product features .................................................................... p04. 02 Warnings .................................................................... p04. 03 Package contents .................................................................... p04. 04 Start-up .................................................................... p05. 05 Cables connection .................................................................... p07.
01 PRODUCT FEATURES/ 02 WARNINGS/ 03 PACKAGE CONTENT EN 01 Product features Maximum Depth: 2,5m Maximum size of the pool: 10m x 5m Input current: 100-130V AC / 200-230V AC Output current: <24VDC 02 !! Warnings !! 2.1 Please refer to the rules of your country regarding swimming pool safety. 2.2 Place the power transformer at least 3.5 m from the pool. 2.3 Make sure that your electrical outlets are properly grounded. 2.
EN QUICK FACTS - To remove the cleaner from your pool, lift the cable slowly and gently until you can grab it by the handle. Use the handle to fully pull out the cleaner - In order to access the filter basket, place hands as shown in picture. Push with thumbs to unlock lid. - Our robots are designed to facilitate the maintenance of your pool. However, they are not intended to clean a pool full of algae and leaves (ex: end of winter period).
04 START-UP EN Power supply Rotary coupling 7310 robot 4.3 Place your power box to a midpoint between the two ends of your pool and at least 3.50 m from the edge of the pool. 4.4 Place the robot in your pool and wait until it is completely submerged. If necessary, help it to sink manually. 4.5 For optimal performance, place your robot in the pool at the furthest possible location from the power source. This is the appropriate length of the cable so that the robot can reach all of your pool.
06 CLEANING THE FILTER BASKET EN 06 Cleaning the filter basket 6.1 In order to access the filter basket, place hands as shown in picture. Push upward 5 cm with thumbs to unlock cover. 6.4 Empty the debris inside the basket. Use a jet of water to rinse the faces inside and outside the basket filter panels. Also inspect and clean the inside and outside of the robot. 6.2 Use both hands to lift the basket with the handles on the sides of the basket 6.
EN 07 Cleaning the impeller Some debriscan clog or be wrapped around the impeller of the pump. By force, these debriscan hinder the proper functioning of the robot or even damage the engine. Regular visual inspection is part of the normal maintenance of the robot. 7.1. Use a flat screwdriver to remove the protective grille. 7.2 Clean the impeller. 7.3 Replace the grill guard.
09 TROUBLESHOOTING EN 09 TROUBLESHOOTING PROBLEM The robot floats on the surface. The robot does not clean all areas of the pool. The robot does not recover debris during operation. Fine particles (dust or dirt, pollen ...) are ejected by the impeller. Page 10 CAUSE(S) - Immersion of the robot in the pool. - Use of the fine filter. - Water level in the pool. SOLUTION(S) - When you put the robot in the pool, let it sink and reach the floor before you turn it on.
EN PROBLEM CAUSE(S) The robot moves in one direction - An object blocks the rollers, the wheels of the robot or interfering with the movement of the robot. The robot does not move and the filtration pump does not work either. The robot doesn't work any longer. -The robot is not connected to a power source. Power off The pump runs but the robot does not move. The robot turns on but stays on the spot.
09 TROUBLESHOOTING EN PROBLEM CAUSE(S) SOLUTION(S) - Connection of the floating cable - Possibility of fault of the floating cable - Possibility of motor leakage - Check the connection of the floating cable. Disconnect and reconnect as needed. - Check the status of the connectors at the ends of your cables (damaged, rusted, etc.
EN 10 Spare partslist DRAWING : ITEM NUMBER SKU PART DESCRIPTION 1 71000 Top Shell. Dark grey 2 71010 Debris basket (parts 16, and17 included) 3 71020 Cover. smoke 4 71040 Impeller 5 71050 Pump motor block 6 71070 Pump cover lid. Black 7 71080 Handle 8 71090 Geared roller tube . Black 9 71100 Bottom chassis. Dark grey 10 71110 Fast drain flap. Dark grey 11 71120 Left Side Support. Black 12 71130 Drive belts. Black - 2 pieces 13 71140 Wheels.
10 SPARE PARTSLIST EN 10 Spare partslist Page 14 DRAWING : ITEM NUMBER SKU PART DESCRIPTION 15 71160 Right Side Support. Black 16 71012 Non return inlet 17 71011 Top filter screen 18 3311 Floating cord 3m - machine end.
EN 11 Spare partsdrawing Page 15
