Instructions / Assembly

ManualsBrandsBlue Wave ManualsOtherSimple Step Grand Entry System with Gate

NE1415W

SIMPLE STEP ENTRY SYSTEM w/ GATE

IMPORTANT INSTRUCTIONS: Read all instructions carefully & completely to become familiar

with parts, assembly, safety and proper use of this product. Failure to follow these

instructions may result in serious personal injury. DO NOT DEVIATE FROM THESE

INSTRUCTIONS & PLEASE REVIEW WITH ALL USING THIS POOL ENTRY SYSTEM

TOOLS REQUIRED: 7/16" socket or nut driver, measuring tape, level, Phillips (star)

screwdriver, utility / trimming knife, a 5/16", 1/4" & 1/8" drill bits & drill and a pad lock

SAFETY INSTRUCTIONS & PROPER USE

• This pool entry system has a 300 lb load capacity - one person - when properly installed

• The entry is designed and intended for use with an above ground pool only (flat bottom)

• Your above ground pool has shallow water - absolutely NO DIVING or NO JUMPING into the pool

• The entry system with gate conforms to the latest revisions of the APSP & ANSI recommended standards for above

ground/on ground swimming pool steps (when properly assembled & installed as per manufacturer’s recommendations)

• For entry & exit of the pool face steps at all times. Use extended handrails at all times for additional safety

• This step system includes a protecting gate - NEVER use entry system without gate attached and fully functional. When

pool is not in use, make certain gate is securely closed, latched and locked at all times to prevent unwanted entry & injury

• Ensure the bottom of the side support stringers are free of debris & any possible sharp edges as not to damage the pool

liner. Use of a ladder or step pad (sold separately) is highly recommended for extra protection & life of the pool liner

• Locate pool steps on a solid / flat base both inside & outside pool. Do not use entry system with “dished” bottom pools

• IMPORTANT: Secure entry system to pool structure for stability and safety - follow instructions closely

• Keep all handrails, platform and treads free from obstructions to avoid possible injury. Do not secure any items to the pool

entry. Such objects (eg. thermometers, toys, ropes) may create a potential for tripping or entrapment & injury can occur

• NEVER ALLOW CHILDREN TO SWIM UNATTENDED - Nothing replaces parental supervision at all times

• Assemble and install this pool entry system as per the manufacturer’s instructions. Do not deviate from these instructions

as serious personal injury or drowning may occur - PLEASE ALWAYS SWIM SAFELY & RESPONSIBLY !

• Please review all instructions for proper use and safety with all individuals using this pool entry system to prevent injury

Step 1: IDENTIFY

PARTS

Top Platform - 1 pc

Upper Handrails - 4 pcs

2 Left & 2 Right

Lower Handrails - 4 pcs

2 Left & 2 Right

Stringers - 4 pcs - 2 Left & 2 Right

R L

Latch Shield

1 pc

Gate Hinges (inner & outer)

2 sets

Gate Stop - 1 pc

Gate - 1 pc

Tread-Riser - 2 pcs

( with light hole)

Tread-Riser - 4 pcs

( without light hole)

Half Bottom Riser - 2 pcs Half Top Tread - 2 pcs

TREAD - RISERS FOR GE POOL STEPS (32")

Summary of content (9 pages)

PAGE 1
NE1415W SIMPLE STEP ENTRY SYSTEM w/ GATE IMPORTANT INSTRUCTIONS: Read all instructions carefully & completely to become familiar with parts, assembly, safety and proper use of this product. Failure to follow these instructions may result in serious personal injury.
PAGE 2
Step 2: IDENTIFY HARDWARE Stainless Lock Pins 4 pcs Hex Nuts 40 pcs Washers 66 pcs # 10 x 3/4" Screws - 6 pcs 1/4 x 1" Bolts - 8 pcs 1/4 x 3/4" Bolts - 30 pcs 1/4 x 3-1/4" Bolts - 2 pcs 3/16 x 3/4” Bolts-Nuts-Washers 2 sets ¾"" Gate Latch & Striker 1 set Hardware Measurement Guide 1"" 3¼"" 3.1 Step 3: FIT TREADS & RISERS INTO STRINGERS Each of the tread riser parts is hollow and contains air.
PAGE 3
.6 5 3.8 5 3.9 3.10 4 1 3 2 1 Identify one of the half bottom riser parts. With the warning signs facing out, away from the steps, fit the bottom riser into the indentation of the stringer at POSITION 1 (see Detail 3.6 & 3.8). Press the bottom riser into the stringer until the button lock knob on the end protrudes through the hole and locks the part in place (see Detail 3.10). Identify one of the half top tread parts.
PAGE 4
Step 5: ASSEMBLE AND FIT UPPER HANDRAILS 5.3 5.4 LEFT RIGHT Identify the upper RIGHT (R) & LEFT (L) handrails (small stamp in parts - see Detail 5.1 & 5.2). Fit handrail pair together as shown in Detail 5.3 - 5.5 aligning bolt holes at top. Secure using 1" bolts, washers both sides and nuts. Tighten hardware. Repeat for both sets of upper handrails. Identify the top platform and with the anti-skid surface facing up, fit the handrail pairs through the platform as shown in Detail 5.6 & 5.7.
PAGE 5
Step 7: ADJUST, MARK & SECURE TOP PLATFORM & ENTRY TO POOL 7.2 7.1 PULL OUT IN-POOL 7.3 POOL WALL It is important before placing entry within pool that you check the bottom of the stringers for any debris or sharp edges as they may cause damage to the pool liner. Use of a step or ladder pad for extra protection is highly recommended. Place entry over pool wall at desired location (Detail 7.1). NOTE: it is important to choose a low traffic area for safety.
PAGE 6
Step 8: FIT & SECURE GATE STOP & GATE HINGE SETS 8.3 8.2 8.1 LEFT L 8.4 The lower LEFT handrail on the exterior portion of the entry has holes to accept the gate hinges & gate stop (see Details 8.1 & 8.2). Begin by securing the gate stop in place (Detail 8.3). Fit the stop on the outside face of the handrail over the center two holes it is form fitting (see Detail 8.4). Secure using two 1/4 x 3/4" bolts, washers on inside & nuts. Tighten hardware.
PAGE 7
Step 9: FIT & SECURE GATE 9.4 9.5 9.3 9.2 9.1 Gently pry open gate hinge sets & fit gate between the inner & outer hinge parts (see Detail 9.1 - 9.5). The “round” posts of the gate will fit through the gap of the hinges (outlined in details above). Secure gate hinges using the remaining 1/4 x 3/4 bolts, washers & nuts. Note that the center holes only require the bolt & nut (no washers will fit). Use washers on both sides for the remaining hardware positions (9.3).
PAGE 8
GATE LATCH SHIELD MAKE CERTAIN TO READ & FOLLOW ALL INSTRUCTIONS CAREFULLY LATCH SHIELD 1.5 - 2 Inches EYE SCREW #10 x 3/4 SCREWS Step 4: Make sure gate latch catch is in down / locked position over striker bar. Extend string upwards to outside face of upper handrail & fold end approx. 1.5 - 2 inches.
PAGE 9
NE1415W - SIMPLE STEP GRAND ENTRY w/ GATE PARTS BREAKDOWN L UPPER LEFT STEP HANDRAIL LEFT STEP STRINGER RIGHT STEP STRINGER R FOLDING TREAD-RISER WITHOUT HOLE UPPER RIGHT STEP HANDRAIL 4 HOLE TOP PLATFORM L LOWER LEFT STEP HANDRAIL FOLDING TREAD-RISER WITH HOLE R LOWER RIGHT STEP HANDRAIL HALF TOP TREAD GATE STOP INNER GATE HINGE OUTER GATE HINGE 3-1/2" GATE HALF BOTTOM RISER 1/4-20 BOLTS PART DESCRIPTION QUANTITY OF PARTS PART # ( COLOR: WHITE ) PART # ( COLOR: TAUPE) LEFT STEP STRING