FlowX Xtreme Pllus Filterr System Manual VER.
CONGRATULATIONS! YOU HAVE PURCHASED A HIGH QUALITY FlowXtreme Plus FILTRATION SYSTEM FOR YOUR ABOVE GROUND POOL. YOUR NEW FILTER SYSTEM HAS BEEN MANUFACTURED AND TESTED TO OFFER MANY YEARS OF TROUBLE FREE SERVICE. IMPORTANT – READ THIS MANUAL CAREFULLY A. Safety Warnings Read all Warnings and Cautions noted below. Failure to do so could result in serious or fatal injury.
B. General Information This manual provides information relating to the installation, utilization and maintenance of our filtration system. We recommend that you read this manual in its entirety and keep it for future reference. The pump included with the filtration system is a horizontal, centrifugal pump. For the pump to function correctly, the water temperature must not exceed 35℃/95℉. The materials used in the pump have undergone stringent hydraulic testing and electrical inspections.
Expendable parts that do not fall under the warranty include: All O-rings Pressure gauge if this filter system is equipped with one Mechanical seal, complete Hoses and metal hose clamps F. Resultant Damages We cannot be responsible for damages to the product if the product is not used in accordance with the instructions provided. G. Technical Data and Specifications 1. Circulation power 1100 GPH 2. Pump is not self-priming 3. Maximum water temperature 35°(95°F) 4. 100W / 115V / 60HZ / 1/10HP 5.
Additional installation accessories such as hoses, hoses clamps are available from your pool dealer. K. Filter-Pump assembly (Figure1) 1. Assemble the filter system at the location where the pump will be installed. The filter pump consists of the following parts: a. 90° connector b. Transparent cover c. Clamping ring d. Filter tank e. 1¼”-1½” return to pool hose fitting f. Tank and pump base plate g. Filter pump h. 1¼” diameter connection hose 2.
7. If the filter-pump system is installed in a location level and lower than your pool’s water level, water will automatically flow into the pump-filter system. 8. Allow the filter tank to fill with water. 9. Check the filter system and the connection hoses for leaks and fix as needed. Leaking at connection points may happen due to manufacturing tolerances, these leaks are easily resolved by wrapping Teflon tape around the connections before the connecting hose is attached. 10.
Malfunctions Causes Solutions Water pressure is low or Cotton Tails looks dirty. The Cotton Tails have absorbed too much dirt & debris from the water. Clean the Cotton Tails filter media. Water flow is too low. Pump gets too little water. Check the suction line and the water level in the pool. Air in the pump. Poor seal on the intake fittings of pump. Tighten hose clamps and connecting fittings. Use Teflon tape if necessary. Open Air vent plug. Leaking pump. Seal is worn out or damaged.
R.
S. FlowXtreme PLUS Filter System, NE4507, Parts Breakdown & Diagram Key Qty Mfg. No. B.W. No.
A ATTENT TION DO N NOT RETURN THIS T PR RODUCT T TO YO OUR RE ETAILER R. IF YOU U ENCO OUNTER R ANY D DIFFICU ULTIES S WITH YOUR NEW N SWIM MMING POOL PUMP P C CONTAC CT BLU UE WAVE E CUST TOMER SER RVICE F FOR AS SSISTAN NCE.
T. Warranty Information This product is warranted to the original purchaser to be free from defects in material or workmanship for a period of one (1) year from the date of the original retail purchase. This warranty does not cover defects or damage due to improper installation, alteration, accident or any other event beyond the control of the manufacturer. Defects or damage resulting from misuse, abuse or negligence will void this warranty.
La garantie du produit est valide pour l'acheteur original en ce qui a trait aux pièces défectueuses ou à la main-d’œuvre pour une période de 1 année de la date d’achat. Cette garantie n’est couvre pas les dommages causés par accident, par modification, par une installation défectueuse ou tout autre événement hors du contrôle du fabricant. Tout défaut ou dommage résultant de la négligence ou d’une mauvaise utilisation annule cette garantie.