V13.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. 2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged. 3. Avoid interference.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord). You must also remove your battery in order to prevent accidentally turning the machine on. Before removing the battery disconnect the AC/DC adapter from the computer.
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern. • Use proper handling procedures when using polymer batteries.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer, use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Ergonomics We designed your Multimedia PC system to be functional as well as attractive. To get most out of it, here are some suggestions on how to position and use the computer: • The top third of the LCD (screen) should be at eye-level or slightly below. • The LCD should be at least 18"/45cm. directly in front of you. • If the screen resolution makes you strain to read, then adjust the resolution to something more comfortable (see “Video Features” on page 1 - 35).
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Wall Mounting Information The computer may be mounted on a wall for display. The system meets VESA MIS-D Standard (100mm * 100mm) for wall mounting. However if you intend to wall mount the system please contact your service center for information in order to avoid personal injury, or damage to the computer.
Preface Contents Notice .............................................................................................................................................................I ErP Off Mode Power Consumption Statement: ........................................................................................... II FCC Statement ............................................................................................................................................
Preface System Map: Front View - Model A .........................................................................................................1-6 System Map: Front View - Model B .........................................................................................................1-7 Tilting the LCD Screen ..............................................................................................................................1-8 Buttons & LED Indicators ..........................................
Preface Running Apps ..........................................................................................................................................1-39 Features & Components Overview ....................................................................................................................................................2-1 Hard Disk Drive .........................................................................................................................................
Preface Power Plans ...............................................................................................................................................3-5 Power-Saving States ..................................................................................................................................3-7 Sleep ..........................................................................................................................................................3-7 Hibernate .................
Preface Driver Installation Procedure .....................................................................................................................4-7 Chipset .......................................................................................................................................................4-7 Video ..........................................................................................................................................................4-7 LAN ......................
Preface MB Series / BIOS Revision / KBC/EC firmware Revision ......................................................................5-6 Advanced Menu .........................................................................................................................................5-7 Intel(R) Anti-Theft Technology (Advanced Menu) ..................................................................................5-7 SATA Mode Selection (Advanced Menu) .....................................................
Preface Removing the Rear Component Cover ......................................................................................................6-6 Inserting the Rear Cover ............................................................................................................................6-8 Upgrading the Hard Disk Drive/SSD ........................................................................................................6-9 Removing the 3.5" (88.9mm) HDD ......................................
Preface Bluetooth & WLAN Combo Module ......................................................................................................7-16 3rd Party Bluetooth (V4.0) Combo Driver Installation ...........................................................................7-17 Intel Bluetooth Combo Driver Installation ..............................................................................................7-17 Bluetooth Configuration in Windows ..........................................................
Preface Card Reader Port .......................................................................................................................................A-2 DC-In Jack ................................................................................................................................................A-2 External Monitor (VGA) Port ...................................................................................................................A-2 HDMI-In Port .............................
Preface Core Logic ................................................................................................................................................C-2 Display ......................................................................................................................................................C-2 Memory .....................................................................................................................................................C-2 Video Adapter .........
Quick Start Guide Chapter 1: Quick Start Guide - Windows 8.1 Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, Multi-in-1 card reader, ExpressCard/34/54) Audio & Printer. • Chapter 3 The computer’s power saving options.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide Not Included Operating Systems (e.g. Windows 8.1) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g.
1 Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8.1 operating system is supported. Note: In order to run Windows without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM). Windows Versions Note that the information included on the following pages is for Windows 8.1 only.
Quick Start Guide System Startup 1. 2. 3. 4. Remove all packing materials, CDs/DVDs and floppy disks etc. Securely attach any peripherals you want to use with the computer to their ports (e.g keyboard and mouse etc.) Attach the AC/DC adapter to the DC-In jack at the rear of the LCD, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. Push the power button at the front of the computer (along the bottom of the LCD) to turn the computer “on”.
1 Quick Start Guide System Map: Front View - Model A 1. 2. 3. 4. 5. 6. 7. 8. Optional Built-In PC Camera PC Camera LED Built-In Microphone LCD Power Button Function Buttons Power & System Activity LED Indicators Speakers 7 6 2 3 1 4 5 Multi Touch Screen 8 7 Note that Model B computers incorporate a touch screen, Model A computers do not.
Quick Start Guide System Map: Front View - Model B 1. 2. 3. 4. 5. 6. 7. 8. Optional Built-In PC Camera PC Camera LED Built-In Microphone LCD with Multi Touch Screen Power Button Function Buttons Power & System Activity LED Indicators Speakers 7 6 2 3 1 4 5 8 Multi Touch Screen 7 6 5 8 Note that Model B computers incorporate a touch screen, Model A computers do not.
1 Quick Start Guide Tilting the LCD Screen It is possible to tilt the LCD screen in order to get the best possible viewing angle of the screen without glare etc. 1. Place one hand at the top of the computer 1 , and use the other to open the stand 2 to an angle of around 15 degrees from the vertical position (the stand will allow you to adjust to the appropriate angle if you pull it out and let it spring back). Adjust the stand to tilt the computer to 15° from the vertical position.
Quick Start Guide 2. 3. Apply pressure with one hand at the top (at point 3 ) of the computer (while holding on to the side with the other hand) to carefully push the LCD screen down in order to tilt it to the appropriate viewing angle (up to 50 degrees from the vertical position). Use one hand at the top of the computer (while holding on to the side with the other hand) to move the computer back to the original position.
1 Quick Start Guide Buttons & LED Indicators The buttons located under the front panel icons allow you to make screen and input adjustments.
Quick Start Guide System Map: Left View Figure 1 - 7 Left View 1. 2. HDMI-In Port Note that the HDMI-In Port supports video and audio signals from attached HDMI devices. 3. 2 Multi-in-1 Card Reader The card reader allows you to use the most popular digital storage card formats: 3 MMC (MultiMedia Card) / RSMMC SD (Secure Digital) / Mini SD / SDHC / SDXC Compatible MS (Memory Stick) / MS Pro / MS Duo 4 4 5 USB 3.0 Port The USB 3.0 port is denoted by its blue color; USB 2.
1 Quick Start Guide HDMI-In Port This computer features an HDMI (High-Definition Multimedia Interface) input port that allows you to display external sources such as Blu-ray players, DVDs, set top boxes and games consoles etc. on your computer screen. The computer itself does not need to be powered on to display video and audio from external HDMI input sources.
Quick Start Guide Menu Button Press and hold the menu button when an HDMI device is connected (when no HDMI device is connected the button as as an Airplane Mode toggle) to the HDMI-In port to bring up the on screen menu. This menu allows you to adjust the Luminance, Color, Volume, On Screen Display and interface Language. Use the decrease/ increase buttons to move up and down the menus, use the menu button to select an item and use the decrease/increase buttons to make adjustments.
1 Quick Start Guide The following table indicates the standard functions when an HDMI cable is plugged in to the HDMI-In port (and the computer is powered on/off). See overleaf for information if the computer is in Hibernate or Sleep modes.
Quick Start Guide HDMI-In Port in Sleep or Hibernate Modes Note that if the computer is in Sleep or Hibernate modes, and no HDMI cable is plugged-in, then the procedure for plugging-in the HDMI cable and using the system as a display device is as follows: 1. 2. 3. 4. 5. 6. 7. The System is in Sleep or Hibernate mode and no HDMI cable is plugged-in. The battery/HDMI icon will be off. Plug-in the HDMI cable. The battery/HDMI icon will turn green for about 8 seconds and then turn off again.
1 Quick Start Guide System Map: Right View Figure 1 - 9 - Right View 1. 2. 3. 4. 5. Optical Device Drive Bay (for CD/DVD Device - see page 2 - 3) Headphone-Out Jack Microphone-In Jack USB 2.0 Port Stand 2 3 Changing DVD Regional Codes Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.
Quick Start Guide System Map: Rear View Figure 1 - 10 Rear View USB Port for Wireless Transceiver 1 Note that the USB port for the wireless transceiver is designed specifically for a USB dongle for an RF Keyboard & Mouse kit (not supplied with this model). Do not use any other USB devices in this port. 3 3 2 7 5 6 4 11 5 5 8 12 9 13 10 11 1. Rear Component Cover 2. Stand 3. Vent/Fan Intake 4. Carrying Handle Area 5.
1 Quick Start Guide USB Port for Wireless Transceiver Note that the USB port for the wireless transceiver is designed specifically for a USB dongle for an RF Keyboard & Mouse kit (not supplied with this model). Wireless Keyboard & Mouse USB Transceiver If you have purchased a wireless keyboard & mouse kit (not supplied with this computer) you can use the USB port located at the bottom left of the rear cover to house the USB transceiver dongle (do not use this port for any other device, see sidebar). 1.
Quick Start Guide Windows Touch Screen Controls/Gestures Model B computers incorporate a Touch Screen and this can be used to navigate through he interface in much the same way as a mouse, touchpad and keyboard. Where you see the instruction to click/double-click an item in this manual, you can choose to tap/double tap the appropriate area of the screen instead. The following gestures are useful when navigating the Windows interface.
1 Quick Start Guide • Swipe from left and back (Display running apps) - Slide your finger from the left and quickly drag it back towards the right to display a list of apps that are currently running. Tap any app to switch to it. • Pull down from the top (Close app) - Close any running app by starting at the top area of the screen and quickly pulling your finger about halfway down the screen.
Quick Start Guide Touch Keyboard If you need to type on screen then the Touch Keyboard will pop up when required (e.g. when you need to type in an internet URL address in Internet Explorer). When the Touch Keyboard is displayed you have several display/input options and these can be accessed from the icon at the bottom right of the keyboard. To access the Touch Keyboard from the Desktop app click/tap the keyboard icon in the taskbar .
1 Quick Start Guide The Touch Keyboard allows you to input text without the use of an actual keyboard., and you can use writing pad to write (continuously or one character at a time) or touch keyboard to input text. Use the Help menu for further information.
Quick Start Guide Keyboard Shortcuts - Windows 8.1 If you are using a keyboard with this system then note the function of the Windows Logo Key & Menu/Application Key (in the Start screen). The following keyboard shortcuts are useful for navigation/operation in Windows.
1 Quick Start Guide Windows Versions Note that the information included on the following pages is for Windows 8.1 only. The Windows 8 interface is slightly different in appearance and in methods of navigation, and a separate manual is provided on the Device Drivers & Manual Disc with reference to Windows 8. Windows 8.1 Control Panel Throughout this manual you will see an instruction to open the Control Panel.
Quick Start Guide Right-click the Start button in the Desktop app (or use the Windows Logo Key + X key combination) to bring up an advanced context menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Search, File Explorer, Command Prompt, Device Manager and Network Connections etc.
1 Quick Start Guide Windows 8.1 Start Screen & Desktop The Apps, control panels, utilities and programs within Windows are accessed from the Start screen and/or Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination). Click the arrow at the bottom of the Start screen to access Apps. Desktop App Figure 1 - 18 - Windows Start Screen 1 - 26 Windows 8.
Quick Start Guide Apps & Tiles The Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps. Accessing Pining/Unpinning All Apps You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area of the Start screen, and you will see the Customize icon.
1 Quick Start Guide Desktop Application When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the Desktop app and left-click. When you move to the lower left hot corner in the Start screen it will take you back to your most recently used app (if one is running).
Quick Start Guide The Charms Bar The right side of the screen displays the Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.
1 Quick Start Guide Charms Bar Items • Search results. • Share : You can search for any file, application, Apps and control panel settings with instantaneous : This button is used to share information with people via mail or social networks. • Start : Click to bring up the Start screen (the same function as pressing the Windows Logo Key or clicking the bottom left of the screen). • Devices : Click this button to change connected peripheral device settings e.g. an external display.
Quick Start Guide Windows 8.1 Control Panel In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel can be accessed in a number of ways in Windows 8.1. • Click Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type Control Panel and select it from the results to the left.
1 Quick Start Guide • When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu. Figure 1 - 25 - Settings Charms Bar (Desktop App Only) • Click the arrow at the bottom of the Start screen and click Control Panel in Apps (Windows System). Figure 1 - 26 - All Apps - Control Panel 1 - 32 Windows 8.
Quick Start Guide • Right-click the lower left hot corner to bring up the menu and select Control Panel (see Figure 1 - 17 on page 1 - 25). Keyboard Shortcut to Control Panel You can also use keyboard shortcuts to access the Control Panel. Press the Windows logo key and X to bring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.
1 Quick Start Guide Windows 8.1 Taskbar In many instances throughout this manual you will see an instruction to access the notification area of the taskbar (system tray). In Windows 8.1 the taskbar is accessed from the Desktop application; if you are in the Start screen you will need to switch to the Desktop. The taskbar is displayed at the bottom of the Desktop screen, and you can see the notification area (system tray) of the taskbar in the bottom right of the screen.
Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows when running the Desktop app (see “Desktop Application” on page 1 - 28 and Appendix C). It is also possible to quickly configure external displays from the Devices menu item in the Charms Bar (see “The Charms Bar” on page 1 - 29). To Configure Displays from Devices (Charms Bar): 1. 2. 3. 4.
1 Quick Start Guide To access Display (Control Panel) and Screen Resolution in Windows: 1. 2. 3. Go to the Control Panel. Click/tap Display (icon) - In the Appearance and Personalization category. Adjust resolution. Right-Click Desktop App 1. 2 3 2. 3. You can right-click (tap and the touch screen until you see a square icon and then release your finger) the desktop and select Screen resolution 1 (Figure 1 - 29). 1 Use the dropbox to select the screen Resolution 2 (Figure 1 - 29).
Quick Start Guide To access the Intel(R) HD Graphics Control Panel: 1. 2. Click/tap Advanced settings 3 (Figure 1 - 29 on page 1 - 36) in the Screen Resolution control panel in Windows. Click/tap the Intel(R)... tab and click/tap Graphics Properties (button) 4 (Figure 1 - 30 on page 1 - 37) . OR 3. Right-click (tap, hold and release) the desktop and select Graphics Properties from the menu. OR 4. Click/tap the icon menu.
1 Quick Start Guide Power Options Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Settings in the Charms Bar in Windows 8.1 may be used to Shut down or Restart (you can also add Hibernate/ Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 9). You can also use the context menu (Shut down or sign out) shut the computer down/restart etc. Shut Down, Restart or Sleep (Charms Bar) 1. 2. 3. Go to the Charms Bar and click Settings.
Quick Start Guide Running Apps To run apps in Windows you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements. Screen Resolution Settings 1. 2. Switch to the Windows Desktop (click/tap the app or use the Windows logo key + D key combination). Right-click a blank area of the Windows Desktop and select Screen Resolution.
1 Quick Start Guide User Account Control Settings If your computer meets the minimum screen resolution requirements, and still you can't run Metro apps, then that you have to check the status of User Account Control (UAC). Metro apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below. 1. 2. 3. 4. Open the Control Panel.
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • Hard Disk Drive Optical (CD/DVD) Device Multi-in-1 Card Reader ExpressCard Slot Audio Features Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 11).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes To change the DVD regional codes: 1. 2. 3. Go to the Control Panel Double-click/tap Device Manager (Hardware and Sound), then click/tap the + next to DVD/CD-ROM drives. Double-click/tap on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
Features & Components 2 Card Reader Cover Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. Figure 2 - 4 Front View 1. Multi-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34. Make sure you install the Card Reader driver (see “ExpressCard/Card Reader” on page 4 - 7).
Features & Components 2 Volume Adjustment The sound volume level can be set using the volume control in the Settings menu in the Charms Bar. Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar notification area/control panel (right-click the taskbar notification area icon to bring up an audio menu).
Features & Components Setup for Audio Recording 2 To record audio sources on your computer at optimum quality follow the instructions below: 1. 2. 3. 4. Go to the Control Panel. Click/tap Realtek HD Audio Manager (Hardware and Sound), or right-click the taskbar icon and select Sound Manager. Click/tap Microphone Effects (tab) in Microphone (tab), and then click/tap to select Noise Suppression (button), or adjust the Recording Volume level to around 60, to obtain the optimum recording quality.
Features & Components 2 2 - 10
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either the AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-In jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Adjust the LCD to a comfortable viewing angle.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound) in the Windows control panel to configure this feature.
Power Management Shutting the Computer Down Note that you should always shut your computer down by choosing the Shut down command as this will help prevent hard disk or system problems. Use the Shut down or sign out item in the Context Menu (right-click the lower left corner of the screen to bring up the menu). 3 You can also use the Power Menu in Settings in the Windows 8.1 Charms Bar. If you want to add Hibernate/Sleep to the Power Menu see “” on page 3 - 9.
Power Management Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one. The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity. Click/tap Change plan settings and then click/tap Change advanced power settings to access further configuration options in Advanced Settings.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click/tap Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off. Win 8.1 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management Configuring the Power Buttons The power button may be set to send the computer in to either Sleep or Hibernate. In Sleep, the LED will blink green. In Hibernate the LED will be orange. If only the display is turned off, the LED will remain green. Click/tap Choose what the power buttons do on the left menu in Power Options to bring up the menu. Password Protection It is recommended that you enable a password on wake up in order to protect your data.
Power Management Adding Hibernate/Sleep to the Power Menu Add Hibernate/Sleep to the Power Menu as follows. 1. 2. 3. 4. 3 Go to the Power Options (Hardware and Sound) control panel (see page 1 - 31). Click/tap Choose what the power buttons do. Click/tap to put a tick in the Hibernate/Sleep box under Shutdown settings. Click/tap Save Changes and close the control panel.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (see your keyboard documentation).
Power Management Ctrl + Alt + Delete Key Combination You can use the CTRL + ALT + DEL key combination from almost any of the Windows interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Log off, Change a password and Task Manager options. If you click/tap the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.
Power Management Battery Information Follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure 3 - 2 on page 3 - 5).
Power Management 3 Windows Mobility Center The Windows Mobility Center (Hardware and Sound) control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery” on page 6 - 3.
Power Management Proper handling of the Battery Pack 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. • DO NOT disassemble the battery pack under any circumstances. • DO NOT expose the battery to fire or high temperatures, it may explode. • DO NOT connect the metal terminals (+, -) to each other.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 1. 2. 3 Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click/tap Change plan settings (after creating it) and click/tap Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click/tap + to expand the battery options.
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation (Windows 8.1) 1. 2. 3. Insert the Device Drivers & Utilities + User’s Manual disc into the computer’s DVD drive. Click/tap the message “Tap to choose what happens with this disc.” Click/tap Run autorun.exe. 4 Driver Installation If you miss the message above you can eject the Device Drivers & Utilities + User’s Manual disc and then reinsert it.
Drivers & Utilities Follow the instructions to install the driver. Alternatively click/tap Start, navigate (Browse..) to the executable file and then follow the manual setup instructions. Note: If you need to reinstall any driver, you should uninstall the driver first. 4 Figure 4 - 2 - Drivers Installer Screens See Figure 4 - 3 on page 4 - 9 for the optional driver installer screen.
Drivers & Utilities Windows 8.1 Driver 4 Page # Windows 8.
Drivers & Utilities Manual Driver Installation Click/tap Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder. Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows Update” on page 4 8 for instructions.
Drivers & Utilities 4 User Account Control New Hardware Found If a User Account Control prompt appears as part of the driver installation procedure, click/tap Continue or Allow, and follow the installation procedure as directed. If you see the message “New Hardware Found” during the installation procedure (other than when outlined in the driver install procedure), click/tap Cancel to close the window, and follow the installation procedure.
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc (for Windows 8.1) into your DVD drive and click/ tap Install Drivers (button). Chipset 1. Click/tap 1.Install Chipset Driver > Yes. 2. Click/tap Next > Yes > Next > Next. 3. Click/tap Finish to restart the computer. Video 1. Click/tap 2.Install VGA Driver > Yes. 2. Click/tap Next > Yes > Next > Next. 3. Click/tap Finish to restart the computer. LAN 1. Click/tap 3.Install LAN Driver > Yes. 2.
Drivers & Utilities Audio 1. Click/tap 8.Install Audio Driver > Yes. 2. Click/tap Next. 3. Click/tap Finish to restart the computer. 4 Note that after installing the audio driver the system will not return to the Drivers Installer screen. To install any of the optional drivers listed overleaf, eject the Device Drivers & Utilities + User’s Manual disc and then reinsert it (or double-click/tap the disc icon in My Computer), and click/tap Option Drivers (button) to access the optional driver menu.
Drivers & Utilities Optional Drivers See the pages indicated in Table 4 - 1, on page 4 - 4 for the driver installation procedures for any modules included in your purchase option. Insert the Device Drivers & Utilities + User’s Manual disc and click/tap Option Drivers (button) to access the optional driver menu.
Drivers & Utilities 4 4 - 10
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.
BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Previous Values with , or Optimized Defaults with . UEFI Boot & POST When UEFI Boot is enabled, then the prompts to press F2 or F7 will not appear. However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities Setup Menus 5 The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options. Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed. 5 MB Series / BIOS Revision / KBC/EC firmware Revision This item contains information on the BIOS version etc., and is not user configurable.
BIOS Utilities Advanced Menu UEFI Boot When UEFI Boot is enabled, then the prompts to press F2 or F7 will not appear. However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up.
BIOS Utilities SATA Mode Selection 5 If you have installed the Windows OS with either IDE or AHCI mode enabled, DO NOT disable the set mode (if you wish to disable the set mode you will need to reinstall the Windows OS). SATA Mode Selection (Advanced Menu) You can configure SATA (Serial ATA) control to operate in IDE (native/compatible), AHCI (Advanced Host Controller Interface) modes from this menu.
BIOS Utilities Security Menu Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 4 Security Menu Set Supervisor Password (Security Menu) You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility).
BIOS Utilities Password Warning If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. 5 The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. 5 - 10 Security Menu Set User Password (Security Menu) You can set a password for user mode access to the Aptio Setup Utility.
BIOS Utilities Boot Menu BIOS Settings Warning Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Previous Values with , or Optimized Defaults with . UEFI Boot & POST When you turn the computer on it will look for an operating system (e.g. Windows 7) from the devices listed in this menu, and in this priority order.
BIOS Utilities Boot Option Priorities (Boot Menu) Press Enter to access the menu, use the arrow keys to move up and down the menu, and press Enter to select a device from the Boot Option # list (the selected device will be highlighted in white). UEFI Boot (Boot Menu) Enable/disable UEFI Boot from this menu. The Unified Extensible Firmware Interface (UEFI) specification provides a clean interface between operating systems and platform firmware at boot time.
BIOS Utilities Exit Menu Figure 5 - 5 Exit Menu 5 Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose Load Setup Defaults to restore the original Setup defaults and return the Setup to its original state, and erase any previous changes you have made in a previous session.
BIOS Utilities 5 5 - 14
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord). These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. Before removing the battery disconnect the AC/ DC adapter from the computer first. 1. 2. 3. 4. 5. Turn the computer off, remove the AC/DC adapter. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place.
Upgrading The Computer 6. 7. Raise the battery up out of the bay 6 Remove the battery 7 . .
Upgrading The Computer Inserting the Battery 1. 2. 3. 4. Insert the battery 1 at an angle and slide it firmly into the battery bay until connected. Insert the battery bay cover by angling it to fit on the right 2 at first, and then click the left side into place 3 . Slide the cover in the direction of the arrow 4 until the top marker of the battery cover icon 5 is aligned with the marker on the side of the computer 6 . Slide the latches 7 towards the lock symbols to lock the cover in place.
Upgrading The Computer Removing the Rear Component Cover Before undertaking any upgrade procedure it is necessary to remove the rear cover component cover to access the components. 1. 2. 3. 6 Turn off the computer and disconnect all cables and peripherals. Carefully place the computer flat with the LCD facing down (make sure you cover the LCD to avoid scratches) so that you may access the rear cover. Remove screws 1 & 2 .
Upgrading The Computer 4. Slide the rear cover up in the direction of the arrow 3 , until the bottom marker of the rear cover icon is aligned with the marker on the side of the computer 4 . 4 4 4 3 4 Figure 6 - 5 Rear Cover Unlock 6 5. Carefully remove the rear cover 5 , and set it aside.
Upgrading The Computer Inserting the Rear Cover 1. 2. Carefully slide the rear cover on to the computer until the marker of the rear cover icon is aligned with the marker on the side of the computer 1 . Replace screws 2 & 3 .
Upgrading The Computer Upgrading the Hard Disk Drive/SSD The hard disk drive can be taken out to accommodate other 2.5"(63.5mm) or 3.5"(88.9mm) serial (SATA) hard disk drives (see “Storage” on page C - 3), or a Solid State Drive (SSD). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in “Driver Installation Procedure” on page 4 - 7), when setting up a new hard disk.
Upgrading The Computer Removing the 3.5" (88.9mm) HDD 1. 2. 3. 4. 5. Remove the battery and rear cover (see pages 6 - 3 & 6 - 5). The hard disk is located at point 1 . Remove screws 2 - 5 from the hard disk bracket. Slide the HDD assembly in the direction of arrow 6 . Life the HDD assembly 7 out of the computer. 2 3 4 5 6 Figure 6 - 8 3.
Upgrading The Computer 6. 7. Remove screws 8 - 13 from the hard disk bracket Remove the left and right side brackets from the HDD. Screwdriver Types 8 10 13 12 9 11 Make sure you use a small manual screwdriver, and not an electrical screwdriver, in the course of the upgrade/disassembly procedures outlined here, due to the delicate nature of the screws. Figure 6 - 9 3.
Upgrading The Computer Replacing the Brackets & Screws in the 3.5" (88.9mm) HDD 1. Screw Types 6 Note that screws 1 & 2, and screws 3 -6 are different. Screws 1 & 2 are for the top of the bracket, and screws 3 - 6 are for the side of the bracket. 2. 3. 4. 5. 6. Before replacing the brackets and screws for any new HDD, it is important to note that there are left and right brackets for the side of the assembly, and the screws need to be inserted in the appropriate order.
Upgrading The Computer 7. 8. 9. It is important to set the screws 7 - 10 (for screwing the HDD assembly to the case) in place in the HDD assembly before sliding the assembly into the case. Once the screws are set in place slide the whole assembly including the screws into place as per Figure 6 - 8 on page 6 - 10. Make sure the HDD is connected to the slot and then tighten the four screws and replace the rear component cover and screws.
Upgrading The Computer Removing the 2.5" (63.5mm) HDD or SSD Foam Insert for SSDs 6 Note that if your computer contains an SSD in the bracket then a foam insert will be supplied. Make sure you have the foam inserted when installing an SSD to this bracket (see “Removing the SSD from the Bracket.” on page 6 16). 1. 2. 3. 4. Remove the battery and rear cover (see pages 6 - 3 & 6 - 5). The hard disk or solid state drive is located at point 1 .
Upgrading The Computer Removing the 2.5" (63.5mm) HDD from the Bracket. 5. 6. Remove screws 1 & 2 and separate the bracket 3 from the HDD 4 . Reverse the process to install a new hard disk. 4 2 6 Figure 6 - 13 3 2.
Upgrading The Computer Removing the SSD from the Bracket. 1. 2. 3. 4. Remove screws 1 & 2 and separate the bracket and sponge assembly 3 from the HDD 4 . Separate the bracket 5 from the sponge 6 . Make sure you insert the sponge when installing a new HDD. Reverse the process to install a new hard disk.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device Drive 1. 2. 3. 4. Remove the battery and rear cover (see pages 6 - 3 & 6 - 5). The ODD is located at point 1 . Remove the screw 2 , and use a screwdriver to carefully push out the optical device out in the direction of the arrow at point 3 . Reverse the process to install any new optical device.
Upgrading The Computer Contact Warning 6 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. Upgrading the System Memory (RAM) The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDRIII (DDR3) type memory modules (see “Memory” on page C - 2 for details of supported module types).
Upgrading The Computer 3. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 2 & 4 ) in Figure 6 - 17. 2 3 Figure 6 - 17 RAM Module Release 6 2 4. 5. 3 The RAM module will pop-up, and you can remove it. Pull the latches to release the second module if necessary.
Upgrading The Computer 6. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory socket (see sidebar note if you are inserting a single module). Figure 6 - 18 RAM Module Removal 6 Single Memory Module Installation If your computer has a single memory module, then insert the module into the Channel 0 (JDIMM1) socket. In this case this is the upper memory socket (the socket furthest from the mainboard). 7.
Upgrading The Computer Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard. Warranty The CPU is not a user serviceable part. Accessing the CPU in any way, may violate your warranty. Unauthorized tampering with the HDD may also violate your warranty.
Upgrading The Computer 6 6 - 22
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules & Options PC Camera Module When the Camera application is run the LED indicator to the left of the camera will be illuminated in red (see 2 Figure 1 - 2 on page 1 - 6). Note that you need to use the Camera app in Windows to take pictures and capture video.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 5. 6. Go to the Control Panel. Click/tap Sound (Hardware and Sound) and click/tap Recording (tab). Right-click/tap, hold and release Microphone (Realtek High Definition Audio) and make sure the item is not disabled. Double-click/tap Microphone (or select Properties from the right-click menu).
Modules & Options Camera App 1. Figure 7 - 2 2. Run the Camera app from the Start screen by clicking on the Camera app icon . The camera interface will display two buttons on the right side of the screen. Camera App Buttons Exposure 7 Use the slider to adjust the Exposure level. 3. 4. 5. Figure 7 - 3 Camera Options 7 - 4 PC Camera Module The upper button is used to record video, and the lower button is used to take still pictures.
Modules & Options Camera Options The Camera Options settings may be accessed as follows: 1. 2. 3. 4. Run the Camera app from the Start screen by clicking on the Camera app icon . While the camera app is running access the Charms Bar (e.g. click Use the Windows logo key + D key combination). Click Settings and then click Options. You can adjust the Photo Aspect Ratio, select the Microphone, Hide/Show grid lines and turn Location Info on or off from the Options panel.
Modules & Options Taking Pictures/Capturing Video 1. 2. 3. 4. 5. 7 Figure 7 - 5 Pictures - Camera Roll 7 - 6 PC Camera Module Run the Camera app from the Start screen by clicking on the Camera app icon . Right-click the screen and select the timer if you require a countdown before capture. Click the appropriate icon to take a picture or start video capture (if video capture begins a timer will appear in the bottom corner of the screen).
Modules & Options Camera Roll 1. 2. 3. 4. Run the Camera app from the Start screen by clicking on the Camera app icon . Right-click on the screen to bring up menu buttons at the bottom of the screen. Click Camera Roll. Click the arrows / (on either side of the screen) to browse through the captured photos/video, and back to the Camera app. Editing Photos 1. Clicking on a captured photo will bring up an app bar with a series of buttons. Figure 7 - 6 Edit Buttons (for Still Photos) 7 2. 3. 4. 5. 6. 7.
Modules & Options photo with the edited changes), Update original (which changes the original picture permanently) or Undo any changes. 9. Click the Edit button to bring up a full suite of tools to edit the photo. 10. Click on the menu headings on the left, and then click on the tool on the right to edit the photo as required. Edit Menu Basic Fixes Light Color Effects Figure 7 - 7 Editing Tools 7 11.
Modules & Options Editing Photos 1. Clicking on a captured video will bring up an app bar with a series of buttons. Figure 7 - 8 Edit Buttons (for Video) 2. 3. 4. 5. Click Delete to remove any video from the camera roll (you will be asked to click Delete again to confirm the deletion). The Open With butt ton will allow you to select a program with which to run the Video. Clicking Slide Show will create a slide show of photos/video in the camera roll. Click Trim to edit the video.
Modules & Options Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive. 7 Note that the Windows 8.
Modules & Options Wireless LAN Module If you have included an Intel® or 3rd Party module in your purchase option make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 4. Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
Modules & Options 3rd Party 802.11b/g/n Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click/tap Option Drivers (button). 3. Click/tap 1.Install WLAN Driver > Yes. 4. Click/tap Next. 5. Click/tap Finish to restart the computer. 6. The operating system is the default setting for Wireless LAN control in Windows (see page 7 - 13). 7 Intel® WLAN Driver Installation 1.
Modules & Options WLAN Configuration in Windows You can configure a wireless connection using one of the following options, however make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins. Charms Bar 1. 2. 3. Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear.
Modules & Options 4. 5. 6. 7. 8. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to find other devices or not. When you are connected to the network access point it will display Connected . Select any connected network and click Disconnect to disconnect from a connected access point. 7 Figure 7 - 11 Networks Connected / Disconnect 9.
Modules & Options Desktop Mode 1. 2. 3. 4. 5. 6. 7. Switch to the Windows Desktop (click the app or use the Windows logo key D key combination). Click the wireless icon in the notification area of the taskbar. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to find other devices or not.
Modules & Options Bluetooth & WLAN Combo Module If your purchase option includes the Combination Wireless LAN & Bluetooth module (either Intel® or 3rd Party) then install the driver as instructed overleaf. Make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Bluetooth Data Transfer 7 Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported).
Modules & Options 3rd Party Bluetooth (V4.0) Combo Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click/tap Option Drivers (button). 3. Click/tap 2.Install Combo BT Driver > Yes. 4. Click/tap Next. 5. Click/tap Finish to restart the computer. 6. See “Bluetooth Configuration in Windows” on page 7 - 18 for configuration instructions. Intel Bluetooth Combo Driver Installation 1.
Modules & Options Bluetooth Headset Stereo Setup To setup a Bluetooth headset to support stereo audio see page 8 13. Bluetooth Configuration in Windows You can configure a Bluetooth connection as below, however make sure the Bluetooth module is on (or the system is not in Airplane Mode) before configuration. Desktop Mode 1. 2. 3. Switch to the Windows Desktop (click the App or use the Windows logo key D key combination).
Modules & Options 4. 5. Make sure that Bluetooth is turned on and a list of discovered devices will appear. Double-click the device you want to pair with the computer and click Pair. Figure 7 - 14 PC and Devices Bluetooth 6. 7 On first connection the computer will provide you with a pairing code to be entered onto the device. Figure 7 - 15 Enter the Passcode 7. 8. Enter the code into your Bluetooth enabled device and click Yes on the computer to complete the pairing.
Modules & Options To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. 4. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Click the notification area of the taskbar, click the Bluetooth icon and click Open Settings. Click Options, and make sure that Allow Bluetooth devices to find this computer check box (Discovery) has a tick inside it.
Modules & Options Trusted Platform (Security) Module The TPM security chip allows you to create and manage digital certificates for user and platform authentication. This type of security is usually administered within large enterprises and organizations, and therefore requires implementation by a system administrator before users can access security features. Individual users can use the TPM as an authentication with the fingerprint reader.
Modules & Options Enabling & Activating TPM 1. 2. 3. 4. 5. 6. Restart the computer. Enter the Aptio Setup Utility pressing F2 during the POST/startup. Use the arrow keys to select the Security menu. Select Configuration and press Enter to access the sub-menu. Press Enter to access the Security Device Support menu and select Enable to display the full TPM configuration menu. Select TPM State, press Enter and select Enabled to change the TPM state to enabled.
Modules & Options 8. Select Pending operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership). You will then need to press F4 to save the changes and restart the computer. Figure 7 - 18 Pending operation (Enable Take Ownership) 7 9. You can now install the TPM driver (see “Trusted Platform Module (TPM) Driver Installation” on page 7 - 24) and then initialize the TPM.
Modules & Options Trusted Platform Module (TPM) Driver Installation 1. Make sure you have enabled and activated the TPM in the BIOS before installing the driver. 2. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 3. Click/tap Option Drivers (button). 4. Click/tap 3.Install TPM Driver > Yes. 5. Click/tap Next. 6. Click/tap the button to accept the license and click/tap Next. 7. Click/tap Next > Next > Install. 8. Click/tap Finish > Yes to restart the computer.
Modules & Options Initializing TPM 1. 2. 3. 4. 5. Switch to the Desktop app and click the TPM icon right-click the icon in the notification area of the taskbar, and select Security Platform Initialization (or click the Security Platform State taskbar bubble). Click User Settings (tab) and click Yes, or right-click the icon in the notification area of the taskbar, and select Security Platform Initialization (or click the Security Platform State taskbar bubble).
Modules & Options 6. Help 7. Choose the Security Platform Features you want to use by clicking the appropriate tickbox. Enter a Basic User Password (and re-type to confirm it) and click Next. Right-click the icon in the notification area of the taskbar to bring up the menu to select Help or How to use the Security Platform Features. 7 You can also click the Help button in any of the Infineon Security Platform Settings Tool tabs to bring up specific help topics on each tab.
Modules & Options Infineon Security Platform Settings Tool The Infineon Security Platform Settings Tool allows you to manage and check the TPM state, manage your password information, and to backup and restore the TPM data. As TPM is usually administered within large enterprises and organizations, your system administrator will need to assist you in managing the information here. Menus Note that not all the menus pictured here will be available for access.
Modules & Options User Settings This page allows the settings to be configured for the currently logged in Infineon Security Platform user including the ability to change the password, configure secure e-mail, file and folder encryption and Enhanced Authentication. You can also import or delete certificates protected by the security platform.
Modules & Options Backup Here you can configure backup and restore operations. Backup files contain the computer identification and user identification information which is used to match the machine name and user name with the current machine and user during restoration.
Modules & Options Migration The Migration tab is used to help securely transfer keys and certificates from one platform to another.
Modules & Options Password Reset Use Password Reset to reset basic user passwords when required.
Modules & Options BitLocker BitLocker Drive Encryption can be used in conjunction with the TPM to encrypt data on the disk and is done via the Microsoft BitLocker Control Panel Applet. Click Configure and select a drive to be encrypted and then follow the Wizard to begin the encryption process.
Modules & Options Access the Microsoft BitLocker Drive Encryption control panel applet from the Windows control panel (System and Security).
Modules & Options Advanced Configure all the Security Platform owner and policy settings from the Advanced tab. The settings that can be changed are for the local computer only.
Modules & Options Wireless Display Wireless Display uses your Wireless LAN module/WLAN Bluetooth Combo module (you need to make sure that your video adapter/display device is compatible with your particular WLAN/Combo module) in conjunction with a compatible video adapter/display device (purchased separately) to allow you to display the contents of the notebook display on another display (e.g. HDTV), without the need to have cables stretching across a room.
Modules & Options Wireless Display Configuration 1. 2. 3. 4. 7 Figure 7 - 29 Add a Wireless Display 7 - 36 Wireless Display Note that no driver or application is required for wireless display in Windows 8.1. Go the Charms Bar, select Devices. Click Project. Click Add a wireless display.
Modules & Options 5. The system will then search for compatible display devices (this may take up to 60 seconds so allow time for this to complete). Figure 7 - 30 Searching For Devices 7 6. 7. 8. Double-click any detected display device in the list. You may then need to input a pin number for the device to which you are connecting. Click Next.
Modules & Options 9. The display will then connect (for specific settings for your display see the documentation supplied with your compatible adapter/display for full details). 10. To disconnect from the display you can select it in PC and Devices > Devices and click Remove Device > Yes; or go to the Project menu (Charms Bar > Devices) and click Disconnect.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “Buttons & LED Indicators” on page 1 - 10) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems & Possible Solutions Problem Possible Cause - Solution The Battery LED power indicator , is blinking orange. Low Battery. Plug in the AC power source. If the computer doesn’t start up immediately, turn it off then on again. You are losing battery power too quickly. The system is using too much power. If your OS has a Power Options scheme (see “Power Plans” on page 3 - 4) check its settings.
Troubleshooting Problem Nothing screen. appears Possible Cause - Solution on The system is in a power saving mode. Press the power button or any configured sleep/resume key combination. The screen controls need to be adjusted. Press the brightness buttons to adjust the settings. If you’re connected to an external monitor, make sure it’s plugged in and turned on. You should also check any attached monitor’s own brightness and contrast controls. The screen saver is activated. Press any key on the keyboard.
Troubleshooting Problem Possible Cause - Solution The Optical Disk Drive tray will not open when there is a disc in the tray. The compact disc is not correctly placed in the tray. Gently try to remove the disc using the eject hole (see “Loading Discs” on page 2 - 3). The DVD regional codes can no longer be changed. The code has been changed the maximum 5 times. See “DVD Regional Codes” on page 2 - 5. The DVD will not play. The computer is tilted beyond 50 degrees.
Troubleshooting Problem Possible Cause - Solution The Wireless LAN/ Bluetooth/PC Camera modules cannot be configured. The driver(s) for the module(s) have not been installed. Make sure you have installed the driver for the appropriate module (see the instructions in Chapter 7 “Modules & Options” for the appropriate module). A file cannot be copied to/from a connected Bluetooth device.
Troubleshooting Problem Possible Cause - Solution I have used Update Driver in Device Manager (Unknown device > Other Devices) to try and install the Airplane Mode driver. Windows encountered a problem in attempting to update the driver, and a yellow exclamation mark appears in Device Manager against the Unknown device. It is very important that the drivers are installed in the order indicated in Chapter 4 (which is the numbered installation order on the Device Drivers & Utilities + User’s Manual disc).
Troubleshooting Problem Possible Cause - Solution I have connected a Bluetooth Mouse but it loses the Bluetooth connection and no longer responds after a short period of inactivity. This is an issue with this mouse model and the Intel Wireless 7260 WLAN and Bluetooth combo module series. To resolve this issue do the following: 1. 2. 3. 4. 5. 6. Go to the Device Manager control panel in Windows. Click the arrow alongside Bluetooth to expand the menu if required.
Troubleshooting Problem Possible Cause - Solution When using a Bluetooth headset the audio appears to be mono and not stereo. This is a common issue with Bluetooth headsets. To resolve this issue do the following (you will need to repeat this procedure after every boot up, restart, or when the system resumes from hibernation): 1. 2. 3. Go to the Devices & Printers control panel in Windows. Double-click the Bluetooth headset. Click Connect to complete the stereo connection. OR 1. 2. 3.
Troubleshooting 8 8 - 14
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Computer Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
Interface (Ports & Jacks) Item Description Headphone-Out Jack Headphones or speakers may be connected through this jack. Note: Set your system’s volume to a reduced level before connecting to this jack. Microphone-In Jack PS/2 Type Keyboard & Mouse Ports Plug an external microphone in to this jack to record on your computer. Connect an external PS/2 type mouse or keyboard to these ports. Port Warning The computer can only accept one keyboard at a time.
Interface (Ports & Jacks) Item Description RS-232 COM/Serial Ports The RS-232 COM/serial is a communication interface for data transfer, through which information transfers in or out one bit at a time. This port can be used to connect the computer to devices such as terminals and peripherals. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. USB 2.0/1.1 Ports These USB (Universal Serial Bus) 2.
Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 35. DVMT Notes Intel Video Driver Installation Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - 4. Video 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click/tap 2.Install VGA Driver > Yes. 3. Click/tap Next > Yes > Next > Next. 4.
Intel Video Driver Controls HDMI-In Port This computer features an HDMI (High-Definition Multimedia Interface) input port that allows you to display external sources such as Blu-ray players, DVDs, set top boxes and games consoles etc. on your computer screen. B Intel® HD Graphics Control Panel Advanced video configuration options are provided by the Intel® HD Graphics Control Panel. To access the control panel see below and overleaf: 1.
Intel Video Driver Controls OR 2. Right-click the Desktop and select Graphics Properties from the menu. OR 3. 4. 5. Click Advanced settings in the Screen Resolution control panel in Windows. Click the Intel(R) HD Graphics Control Panel tab and click Graphics Properties (button). Double-click the Intel(R) HD Graphics control panel in the Windows Control Panel.
Intel Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu panel and adjusting the settings on the right.
Intel Video Driver Controls Sub-Menus Some of the menu panels will also have sub-menus (in the top left corner of the menu alongside the icon ) to display further configuration options.
Intel Video Driver Controls Multiple Display Display Click either Display Settings or Color to make display adjustments, including configuration for any attached external displays. At least one other display must be attached in order to view multiple display selection options.
Intel Video Driver Controls Click the Display menu at the top of the screen to display the sub-menus. The Multiple Displays menu allows you to configure the display mode of any attached displays (see “Attaching Other Displays” on page B - 16). Multiple Display At least one other display must be attached in order to view multiple display selection options.
Intel Video Driver Controls The Audio sub-menu allows you to configure the capability mode of any attached displays if applicable (i.e. the attached display supports audio).
Intel Video Driver Controls 3D This menu allows you to choose how 3D images are displayed. Quality displays the most detail, Balanced provides better computer performance with good quality and Custom allows you to configure the Anisotropic Filtering, Vertical Sync and Anti-Aliasing features to your preferences. Click Apply to save changes.
Intel Video Driver Controls Options Options allows you to Customize Hot Keys (for opening the application, rotating the display, scaling etc.,) to your preferences. Click Apply to save changes.
Intel Video Driver Controls Click the Options menu at the top of the screen to display the sub-menus. The Information Center provides details on System Information, the Built-In Display and any attached displays. Preferences Go to the Preferences sub-menu in Options to configure the preferences for the Intel® HD Graphics Control Panel. Make sure you turn Tray Icon On to display the Intel® HD Graphics Control Panel icon in the notification area of the taskbar (as below).
Intel Video Driver Controls Video The Video Profiles menu allows you to brighten or darken movies, or to switch to vivid colors. Click Basic or Advanced to adjust the video settings. The Preview image will display a sample image using the current settings. You can Save Profile and name the Profile to recall the settings at any time. Click Apply to save changes.
Intel Video Driver Controls Click the Video menu at the top of the screen to display the sub-menus.The Image Enhancement menu allows you to adjust the Sharpness and Skin Tone Enhancement. Click Apply to save changes.
Intel Video Driver Controls The Image Scaling and Gamut Mapping menus allow you to adjust these items.
Intel Video Driver Controls Display Devices & Options Besides the built-in LCD you can also use external monitors/flat panel displays/TVs connected to the HDMI-Out port (High-Definition Multimedia Interface) and/or external monitor port as your display device. Attaching Displays When you first attach an external display you may find that the desktop does not occupy the full screen area.
Intel Video Driver Controls Multiple Display At least one other display must be attached in order to view Multiple Display selection options. Attaching Other Displays To Clone Displays: 1. 2. 3. 4. 5. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Clone from the Select Multiple Display Mode menu. Click Apply, and OK to confirm the settings change.
Intel Video Driver Controls To Enable Extended Mode: 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Extended from the Select Multiple Display Mode menu. Click Apply, and OK to confirm the settings change. Click the appropriate monitor icon and drag it to match the physical arrangement you wish to use (e.g.
Intel Video Driver Controls To Enable Collage Mode: 1. Collage Mode 2. Collage mode is used to combine a number of displays into a single unified higher resolution for larger screen sizes,. 3. 4. 5. 6. Attach your external displays to the external monitor port and HDMI-Out port, and turn them on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Collage from the Select Multiple Display Mode menu. Click Enable Collage and click On.
Intel Video Driver Controls Attaching Other Displays - Devices (Charms Bar) You can configure attached displays from Devices (in the Charms Bar). 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go the Charms Bar, select Devices. Click Project (you may need to click Second Screen). Click on any one of the options from the menu to select PC screen only, Duplicate, Extend or Second screen only.
Intel Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: Configuring an External Display In Windows 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Screen resolution control panel (see page 1 - 33) in the Desktop app. Click the Detect button. The computer will then detect any attached displays.
Intel Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure B - 19 Screen Resolution Multiple Display Options B • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
Intel Video Driver Controls Volume Adjustment The sound volume level can be set using the volume control in the Settings menu in the Charms Bar. HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below. 1. 2. 3. 4. Go to the Control Panel.
Intel Video Driver Controls 5. 6. Adjust the HDMI settings from the control panel tabs. Click OK to close the Sound control panel.
Intel Video Driver Controls Other Applications If you are using a third party application to play DVDs etc. from any attached DVD device, you will need to consult the application’s documentation to see the appropriate audio configuration (the application must support digital to analog translation). HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device.
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Specifications Processor Intel® Core i7-4702MQ (2.2GHz) Mobile Processor 6M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 37W Intel® Core i7-4600M (2.9GHz) Mobile Processor 4M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 37W Intel® Core i5-4330M (2.8GHz) Mobile Processor 3M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 37W Intel® Core i5-4300M (2.6GHz) Mobile Processor 3M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 37W Intel® Core i5-4200M (2.
Specifications Storage One Changeable 2.5" 9.5 mm (h) / 7mm (h) SATA (Serial) Hard Disk Drives One Changeable 3.5" 25 mm (h) SATA (Serial) Hard Disk Drives One 12.
Specifications Power Environmental Spec Full Range AC/DC Adapter – AC in 100 240V, 50 - 60Hz DC Output 19V, 4.74A (90 Watts) Removable 6 Cell Smart Lithium-Ion Battery Pack, 62.16WH (Factory Option) Temperature Operating: 5°C - 35°C Non-Operating: -20°C - 60°C Relative Humidity Operating: 20% - 80% Non-Operating: 10% - 90% Security Physical Dimensions & Weight Security (Kensington® Type) Lock Slot BIOS Password Trusted Platform Module 1.2 525mm (w) * 49mm (d) * 418mm (h) Operating System Windows® 8.
