E51 E50 E56 ELECTRIC RANGE AND COOK TOP
MANUFACTURED BY Moffat Limited P O Box 10-001 Christchurch New Zealand Ph: (03) 3891-007 Fax: (03) 3891-276 WORLD-WIDE BRANCHES UNITED KINGDOM Blue Seal Units 6-7, Mount Street Business Park Mount Street, Nechells Birmingham B7 5 QU Ph: (121) 327-5575 Fax: (121) 327-9711 UNITED STATES Moffat Inc 3765 Champion Blvd Winston-Salem North Carolina 27115 Ph: (336) 661 0257 Fax: (336) 661 9546 CANADA Lessard Agencies Ltd P O Box 97 Stn D Toronto Ontario M6P3J5 Ph: (416) 766-2764 Fax: (416) 760-0394 NEW ZEALAND Chr
BLUE SEAL ELECTRIC HOBS & RANGES - E51 - E50 - E56 ELECTRIC BOILING TABLES ELECTRIC RANGES ELECTRIC CONVECTION RANGES CONTENTS PAGE SPECIFICATION 1 INSTALLATION 2 OPERATING INSTRUCTIONS 4 CLEANING 6 SERVICING INSTRUCTIONS 7 PROBLEM SOLVING 9 WIRING SCHEMATICS 12 SPARE PARTS 16 Date Purchased..................................................... Serial No......................................… Dealer...........................................................................................
SPECIFICATION RANGES INCLUDED IN THIS SPECIFICATION: E51-4D E51-4C E51-4B 4 radiant elements, Boiling table 2 radiant elements plus 300mm griddle, Boiling Table 600mm griddle, Boiling Table' E51-6D E51-6C E51-6B E51-6A 6 radiant elements, Boiling table 4 radiant elements plus 300mm griddle, Boiling Table 2 radiant elements plus 600mm griddle, Boiling Table 900mm griddle, Boiling table E50-D E50-C E50-B E50-A 6 radiant elements plus static oven 4 radiant elements plus 300mm griddle plus static oven 2 ra
INSTALLATION It is most important that the unit is installed correctly and that the operation is correct before use. Installation must comply with national electrical installation codes and local Health and Safety regulations. IMPORTANT - FIXED WIRING INSTALLATIONS MUST INCORPORATE AN ALL-POLE DISCONNECTION SWITCH. A. BEFORE CONNECTION TO POWER SUPPLY Unpack and check unit for damage and report any damage to the carrier and supplier. Report any deficiencies to your supplier.
INSTALLATION Using the V P I triangle, total the loads on the one circuit (P) and divide by the supply voltage () to determine the current (I) drawn. Look up the current drawn and install the corresponding wire. Example: One Line: 3300W + (2 x 40W) + 180W + 5W = 3645 Watts Elements 2 lights Motor Buzzer 3645 = 15.19 Amps 240V Therefore sizing up, use 1.5mm² wire. D. CONNECTION Connection to power supply must be carried out by a Registered Electrician.
OPERATING INSTRUCTIONS A. RADIANT HOTPLATES The controls for the radiant hotplates may be set at any position between high and low to provide the desire level of heating. An individual pilot light for each element will glow when the element cycles on and extinguish when the element cycles off. Start cooking at the highest setting, and change to a lower setting when the desired temperature is reached.
OPERATING INSTRUCTIONS D. CONVECTION OVEN (E56 SERIES) The oven is fitted with a fan, top and bottom elements. maintains the oven temperature by controlling both element. The thermostat Place oven racks in the desired position. 1. PREHEAT the oven by selecting the desired temperature. desired temperature is reached, the pilot light will go out. When the 2. COOKING - When the desired temperature has been reached, proceed cooking.
CLEANING CAUTION: ALWAYS TURN THE POWER SUPPLY OFF AT THE WALL SWITCH BEFORE CLEANING THIS UNIT IS NOT WATER PROOF. DO NOT USE WATER JET SPRAY TO CLEAN INTERIOR OR EXTERIOR OF THIS UNIT. A. RADIANT HOTPLATES Wipe the surface while still warm to remove spill-overs, grease etc. before they harden. As soon as hotplates have cooled, wipe all over with a damp cloth. Raise the side of the hotplate module and withdraw, clean and dry the spill-over dish. B.
SERVICING INSTRUCTIONS ENSURE POWER SUPPLY IS SWITCHED OFF BEFORE SERVICING. All servicing should be carried out by a competent electrical appliance serviceman with experience of commercial cooking equipment. A. CONTROL PANEL Undo the screw(s) at the top of the control panel and swing the panel down. FUSES are now accessible. E50, E56 Series Undo the screw at the right hand side of the control panel cover and swing the cover to the left.
SERVICING INSTRUCTIONS E. RADIANT AND SOLID ELEMENTS Tilt element sideways and remove spillage tray. Lift front of element, pull forward approximately 30mm and turn on edge. Remove terminal cover plate and disconnect wiring. Radiant Element 2.4kW at 240V = 10A 24 ohms Solid Elements 2.0kW at 240V = 8.3A 29 ohms F. ENERGY REGULATORS These should be checked for positive OFF and MAXIMUM positions and for correct cycling throughout the control range. G.
PROBLEM SOLVING A. FAILURE OF INDIVIDUAL ITEMS, e.g one element Note: Switch off power supply or remove wall fuses for these tests. Check individual fuses located behind control panel. Check for an electrical short by checking there is NO continuity between any "phase in" line and the metal appliance body itself. Check for the item failing (element, control etc) by using a multimeter as shown on following pages. Ensure correct size supply wire as described on Page 2. B.
RESISTANCE TEST To check if an element is still functioning correctly, disconnect appliance from the mains supply, disconnect wires from the element and check the resistance (ohms) across the element when cold. Follow Steps 1, 2, 3 below to calculate the correct resistance (OHMS LAW).
CONTINUITY TEST To check if an Energy Regulator, Thermostat or Switch is functioning correctly, disconnect appliance from the mains supply, disconnect wires from the control and check for continuity.
CIRCUIT SCHEMATICS -12-
CIRCUIT SCHEMATICS -13-
CIRCUIT SCHEMATICS -14-
CIRCUIT SCHEMATICS -15-
SPARE PARTS BLUE SEAL E50/51/56 SERIES Part No Description 011654 010419 015710 010137 013600 010422 015533K 011987 015966 015500 013528 010909 019479 010866 010856 004094 017928 Oven Top Element 1.75kW (E56) Oven Top Element 3kW (E50) Oven Bottom Element 4.5kW Radiant Surface Element 2.4kW Cast Surface Element 2.0kW Griddle Element 3.
