SportLift™ III OPERATOR, PARTS AND INSTALLATION MANUAL ’s built to t i w o n k u o y o S . x O It’s from Blue ugh. SC4200 292-2880 Rev. B SportLift III Capacities LIFTING CAPACITY - ......................... 1000 LBS. FLAT-TOWING CAPACITY - ................ 5000 LBS. CARGO HAULING LENGTH - ...... 102 INCHES OR LESS THANK YOU for purchasing a SportLift III from Blue Ox. We’ve organized this manual to make your installation simple and as trouble-free as possible. Ensure it is read.
SC4200 SportLift III Installation Instructions 34 28 29 32 12 27 31 30 26 18 14 15 25 24 23 22 21 1 20 2 3 19 4 18 5 6 33 12 10 9 8 7 292-2880 Rev.
SC4200 SportLift III Installation Instructions Parts List Ref. No. Qty. Part # Description 1 SC9000 Receiver Hitch (Optional-Recommended) 2 1 202-0090 3/8”-16 Hex NYL. INS.
SC4200 SportLift III Installation Instructions DO NOT INSTALL OR USE THIS EQUIPMENT UNTIL THE FOLLOWING OPERATING AND INSTALLATION INSTRUCTIONS HAVE BEEN READ AND UNDERSTOOD. IMPORTANT NOTES BEFORE INSTALLATION INSTALLING HITCH RECEIVER • Be sure to read the “Lift & Carrier Initial Information Sheets” to figure out if the SportLift III can be applied to the motorhome chassis and to figure out how much weight will be added to the rear axle of the motorhome. 1.
SC4200 SportLift III Installation Instructions 5. Using two (2) 3/4” x 4” pins with clips, attach the pickup tube to the arm assemblies on both sides. Step 2 Step 5A After securing the arm assembly to the receiver hitch, secure the arm assembly in the upright position with a 3/4” x 4” pin with clip. 3. Step 5B Step 3 4. Repeat steps 2 & 3 for the passenger side arm assembly. 6.
SC4200 SportLift III Installation Instructions Step 6B Using four (4) 7/16”-14 x 3” hex bolts, four (4) 7/16” flat washers and four (4) 7/16”-14 lock nuts, bolt down towing receiver weldment to the top of the driver side and passenger side base weldments. Then insert two (2) 7/16”-14 x 1-1/4” hex bolts and two (2) 7/16” lock washers into the inside of the towing receiver weldment on both sides. 9.
SC4200 SportLift III Installation Instructions 10. Position winch assembly on the winch mount weldment toward the end on the drivers side. Bolt in place with two (2) 3/8”-16 x 1 1/4” hex bolts, two (2) 3/8” lock washers, two (2) 3/8” flat washers and a 3/8”-16 hex nylon lock nut. Put the nut on the very outside bolt, on the inside of the tube. Step 11 Step 10 11. Once the winch is secure, the wiring should be routed from the winch to the existing battery on the coach.
SC4200 SportLift III Installation Instructions 15. For installation of the round tail lights, please refer to the installation instructions for the SC9005 included with the SC4200. FLAT-TOWING WITH THE SPORTLIFT™ III 1. Using winch, raise arm assemblies up to release pressure from the 3/4” x 4” pins with clips. Pull pins from arm assemblies and lower deck to the ground and load cargo onto the deck of SportLift III. Once the cargo is postioned correctly on the deck, use tiedowns to fasten cargo securely.
SC4200 SportLift III Installation Instructions MAINTENANCE LOADING THE SPORTLIFT™ III Wiping SportLift III down periodically will help keep dust and dirt from building up. • Before a vehicle can be flat-towed, the deck needs to be pinned into place on the arm assemblies. • Make sure the deck of the SportLift III is perfectly level once installed. • SportLift III can flat-tow a vehicle behind it that weighs no more then 5,000 lbs.
SportLift™ III One Year Warranty Automatic Equipment Manufacturing Company (“Automatic”) warrants to the first retail purchaser that each base plate, tow bar, hitch and accessory manufactured by Automatic shall be free from defect in material and workmanship under normal use and service for as long as the original retail purchaser owns the item.
SC4200 SportLift III Installation Instructions To find the Blue Ox dealer nearest you, visit www.blueox.com or call 402-385-3051. Serial Number Customer Service Commitment Blue Ox is committed to providing you with exceptional customer care throughout your lifetime with our products. Our team is here to assist you with any questions you may have regarding the performance of your product. Simply call (402) 385-3051 and you can speak with our customer care team.